HIK VISION DS-k2210 Manuel utilisateur
Title:
Elevator control wiring and simple
configuration （Button mode）
Version:
v1.0
Date:
5/12/2017
Product:
Access Control Device
Page:
1 of 7
Elevator control wiring and simple configuration
（Button mode）
Preparation：
Prepare the following equipment for the test, complete the test and then install
DS-k2210 DS-k2m0016 DS-k1106
Step 1: DIP Switch
The DIP switch of the card reader should be decimal 1 or 2.
The DIP switch of Ds-2100 should be decimal 1or 2.
The DIP switch of distributed elevator controller (DS-K2M0016A) is decimal 3-10
The device uses binary dialing codes
If you want to get dialing 3, Dial 1 and 2,if you want to get 4, Dial 3
Step2:Wring
Title:
Elevator control wiring and simple
configuration （Button mode）
Version:
v1.0
Date:
5/12/2017
Product:
Access Control Device
Page:
2 of 7
Step 3:Installation
Installation of elevator controller and Elevator button connection
controller installation diagram
Principle:
Button（The DIP switch of distributed elevator controller (DS-K2M0016A) is decimal 3-10）： We
control the buttons in the elevator, just put the NC and COM into the button circuit, if the
permission is verifiable，the relay will action and you can press the corresponding button. This part
we need use NC and COM, because the NC and COM is disconnected when the controller with
power supply，and it will be the opposite without power supply in button mode. The advantage
of this mechanism is the controller will release control without power supply，which can avoid
hidden dangers.
Connect the relay string to the corresponding button
Title:
Elevator control wiring and simple
configuration （Button mode）
Version:
v1.0
Date:
5/12/2017
Product:
Access Control Device
Page:
4 of 7
To activate the password, you must check “Export to Group”
5.Determine the controller to display online
6.Configuring the correspondence between floor and relay
Note:Drag the right relay to the corresponding floor
Click on the upper right corner after the configuration is completed.
The first number of the right relay is based on the Numerical Value of the dip switch
7.Set the delay time for each floor by default to 120s, which can be set to 15s
Title:
Elevator control wiring and simple
configuration （Button mode）
Version:
v1.0
Date:
5/12/2017
Product:
Access Control Device
Page:
5 of 7
8.add the staff permission
9.Add a person's card
10.Add permissions, check permissions and click on the right direction to click ok
11.When you click ok, you will be prompted to send it, and you can click directly.
Title:
Elevator control wiring and simple
configuration （Button mode）
Version:
v1.0
Date:
5/12/2017
Product:
Access Control Device
Page:
6 of 7
12.Can also be selected permissions set after clicking all issued (delete permission first,
then issued all permissions, generally after adding new equipment use) or move issued
(group permission to use when there is new change).
Step4 :Validate
I give this card the permission of the first three floors，after swiping card，We can see
the corresponding relay acted by these pictures。
Title:
Elevator control wiring and simple
configuration （Button mode）
Version:
v1.0
Date:
5/12/2017
Product:
Access Control Device
Page:
7 of 7
First Choice for Security Professionals
HIKVISION Technical Support
Autres manuels pour DS-k2210
2
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels HIK VISION Contrôleurs
HIK VISION
HIK VISION DS-K2M0016A Manuel utilisateur
HIK VISION
HIK VISION DS-C12L Series Manuel utilisateur
HIK VISION
HIK VISION C30 Series Manuel utilisateur
HIK VISION
HIK VISION DS-K4H250S Manuel utilisateur
HIK VISION
HIK VISION DS-K1T502 Series Manuel utilisateur
HIK VISION
HIK VISION DS-K2M0016A Manuel utilisateur
HIK VISION
HIK VISION DS-k2210 Manuel utilisateur
HIK VISION
HIK VISION DS-C30S-S23 Manuel utilisateur
HIK VISION
HIK VISION DS-MDH005-B Manuel utilisateur
HIK VISION
HIK VISION DS-k2210 Manuel utilisateur
