Herschel HS220UD Guide de configuration

Select Under desk heater

Select under desk heater

Smart infrared panel heaters

Select Under desk heater

HS220UD HS220UD-EU

Models

Setup and operating guide

The product complies with European Safety Standards Low Voltage Directive 2014/35/EC, EMC Directive 2014/30/EC, RoHS 2011/65/EC & Ecodesign

requirements for local space heaters 2009/125/EC.

Original instructions covering Select under desk heaters produced from 08/2020 onwards

Notice to the purchaser

Before using this product, you should determine its suitability for its intended use. Herschel Infrared Ltd cannot

accept responsibility for damage, loss or injury caused by ingress of water or moisture, accidental damage,

mishandling, external impact, adjustment by unauthorised personnel or failure to follow the correct maintenance

and safety precautions as stated in this manual. Refer to Herschel Infrared Ltd’s warranty policy for full details. See

https://www.herschel-infrared.com.

Select under desk heater

IMPORTANT SAFETY PRECAUTIONS

Failure to observe these instructions will invalidate the warranty.

Do not disassemble. No user-serviceable parts inside.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY

This appliance must be disconnected from its power source during setup or service activities and when replacing.

The heater is equipped with a sensor providing temperature control of the unit and the surrounding area.

Nevertheless the panel surface can rise to 90°C / 194°F (depending upon input voltage) and must not be operated in

locations where people can fall or become immobile next to the heater.

DO NOT touch the heater when in use. Prolonged contact with the heater will cause burns and injury.

The heater has internal safety thermal cut out sensors. However, in order to avoid overheating and potential fire

hazard, DO NOT cover the heater under any circumstances. DO NOT locate the heater within 300mm of any

flammable materials (eg. Furniture, curtains).

DO NOT operate the heater if the cord or plug is damaged or after the heater malfunctions, or if it has been

dropped or damaged in any manner. Make sure that the heater itself, the plug and the cable are free of any visible

signs of damage. If the cord is damaged the appliance must be sent for repair to an authorised Herschel Dealer.

This heater must only be used for the heating of people or buildings. The heater is not to be used by children or

persons with reduced physical, sensory or mental capabilities, or lack of experience or knowledge. Children should be

kept away and should not be left unsupervised around the unit. DO NOT use outdoors.

All operators should only switch on/off the appliance provided that it has been placed or installed in its intended

operating position in accordance with these instructions. Children must not plug in, switch on or regulate the

appliance or perform user maintenance including cleaning.

The heater must be mounted on a non-flammable surface. To avoid the heater tipping over the surface must be

horizontal, even and un-broken.

DO NOT place this heater directly underneath mains sockets.

Herschel panels are designed for use with an AC voltage between 220-240 volts, 50 Hz AC.If your supply voltage

exceeds 240 Volts do not use the heater and refer to your local dealer. Failure to adhere to this will void the

warranty.

This heater is a Class 1 appliance and must be earthed. The electrical supply to each heater should be protected by a

fuse or residual current device with overcurrent protection (RCBO) or Ground Fault circuit interrupter (GFCI ) suitable

for the electrical rating of the appliance.

For certain public buildings like schools and care homes the heaters must be operated according to the specific

legislation for these types of buildings. Please check before use.

Select under desk heater

CAUTION

Any fixed mains wiring outside the heater coming into contact with the heater must be protected by sleeving with

a temperature rating of at least 90°c.

Ensure that the power cable is not coiled. DO NOT attach excess mains cable to any part of the heater.

DO NOT drill through the heater as this will cause irreparable damage and is also dangerous.

DO NOT connect a heater that is damaged in any manner to the power network.

For mounting the Herschel heater use the supplied feet only and install in accordance with this installation

guide.

WATER INGRESS PROTECTION IP44

Herschel Select under desk heater panels are rated to a standard (minimum IP44). DO NOT place within the

immediate surroundings of a bath, shower. It must not be possible for the switches on the heater to be operable by

anyone in a bath or shower. NEVER operate the foot switch with wet feet. It must not be possible for the heater

to be moved or knocked so as to fall into a bathtub, shower, swimming pool or other water container. DO NOT

allow the mains cable or foot switch to rest in water.

Herschel Infrared Ltd shall not be liable for any loss, damage or injury caused or resulting from inadequate fitting or

incorrect placement of heaters close to water sources.

SAVE THESE INSTRUCTIONS.

service/warranty-registration/ or via theQR code.

Within five years from date of purchase Herschel will repair or replace the heater

where the fault is due to defects in materials or workmanship. This warranty is for

standard domestic use only and excludes commercial uses. In the event of a

warranty claim please visit the Customer Service area of the Herschel Website and

follow the Warranty Claim process. You will need proof of purchase and

photographs of the heater.

A prerequisite for validity of the warranty is use at the specified supply voltage of

the heater and use in accordance with the conditions specified in this manual. Any

further warranty or claims are excluded.

5 YEAR WARRANTY

The warranty covers the repair or replacement of the defective product only and Herschel shall have no liability for

installation costs or consequential loses however incurred. The decision to repair or replace will rest solely with

Herschel and any replacement will be as close as possible in specification to the failed heater.

Removing the serial number will void the warranty. The warranty will also be void if the heater has been tampered

with or opened in any way.

The product power label must be left on the panel.

Herschel Infrared Ltd will assume no responsibility for scratches on the surface after first use.

Note your serial number for future reference

Select under desk heater

Thankyou for purchasing a Herschel Select under desk heater infrared heater. Incorporating the very latest in control

with Herschel’s SMART-R system and slimline frameless design, you will enjoy many years of low energy, smart and

comfortable heating.

We’ve tried to make setting up and using your heater as easy as possible. Please read these instructions fully and

retain for future reference. If you have any questions our website also has many FAQs or you can call, message or

online chat with us, we are always happy to help ensure that you get the most from your new Herschel heating

system.

This is a low energy use infrared panel heater. It is

designed to provide a gentle warmth for your legs and

feet under a desk or in close proximity to you.

It is intended as a supplementary heater, not as the

main heat source for a room.

Place the heater where it will not be immediately

obstructed by objects (like bags or folders under a

desk) or where it cannot effectively radiate out, such

as at the edge or in the corners of a room. Large

objects placed in front of the heater will heat up and

can prevent effective heat dispersion.

The heater must be placed on horizontal, even and

unbroken surface.

The feet supplied with the heater must be used and

provide the correct distance for the heater from the

floor and any rear surface (like a wall or the back of a

desk). The heater must be at least 300mm from

objects placed in front.

Positioning your Under desk heater

300mm minimum distance from objects

Your new Herschel Heater

Select under desk heater

The Select under desk heater comes with a

factory fitted plug and can be plugged into

an available socket under the desk.

Setup

1. Find the two feet supplied in the

package.

2. Fit to the long lower side of the heater.

The SMART-R power box at the back of

the panel should be at the bottom edge

of the heater.

3. Use a screw driver to tighten the friction

screws against the rear surface of the

heater. (Note: tightening the screws

against the front will damage the front

surface of the heater).

The SMART-R receiver allows your under desk

heater to operate in two different ways

according to preference:

•It can act in a simple “on /off” mode using

the foot control;

•It can connect to wifi and be managed via

the SmartLife App.

Controls on the SMART-R receiver are as

follows:

1. LED display showing setpoint

temperature

2. Wifi indicator

3. Timer On/Off indicator

4. On / Off button

5. Manual pairing button

6. Manual Temperature Increase

7. Manual Temperature Decrease

8. Built-in Thermostat. Pull gently

downwards to sense the temperature

around the heater.

9. Power Switch (I = On, O = Off)

10. Mains cable

11. Foot Switch.

Select under desk heater

Operation

Simple On /Off operation using Foot Switch

The heater can be simply operated using the foot switch.

ECODESIGN Notice:

When used in this simple operating mode, the Select under desk heater should only be used in well insulated

spaces for occasional use and should not be left operating permanently switched on.

Operation

To use the heater with the foot switch:

Pull the thermostat (8) gently out from the bottom of the SMART-R box until it stops.

Switch the mains socket ON.

Switch the Power Switch (9) on (‘I’ position on rocker switch).

Click the foot switch until the Power Switch (9) illuminates RED.

The heater will warm up until it senses the local temperature of 37°Cis reached at which point it will switch off.

You can lower the set temperature using the –button on the side of the SMART-R receiver. You can only raise the

temperature (using the + button) to 37 °C.

You can switch the heater off and back on immediately using the foot switch.

Heater control using the Smartlife App

The Select under desk heater can be more comprehensively controlled using the SmartLife App. This allows you to

set a heating schedule including an AWAY (Holiday) mode and enables voice control via Alexa or Google Assistant.

You can still also operate the foot switch to turn the heater off and on.

ECODESIGN Notice:

When used with the SmartLife App, the Select Under Desk Heater is fully ECODESIGN compliant and can be

permanently set up and left switched on.

Scan the QR code below to download the Smartlife App from the App Store or Google Play.

Alternatively, search “Smart Life” on Google Play or the App Store & look for this icon.

Downloading & Installing the Smartlife App

After installing and opening the Smartlife App, you must register an account using an email address and password

and accept the terms of use.

Before starting pairing, please ensure:

- Your mobile phone is connected to the 2.4GHz wifi signal from your router. Some routers also issue a 5GHz

signal, so be sure to select the 2.4GHz option.

- Switch off “Wifi Assist” (IoS phones). You can switch it back on after pairing.

-Be sure to be connected to your main router and ensure your heater is within range of your router.

Select under desk heater

Operations available on the SmartLife App

From the main screen of the Smartlife app, you can access the following management features for the heater,

which are described more fully on the following page:

- Power On / Off (turns the heater on and off)

- Temperature override (Orange circle with + and –buttons)

- Manual Operation

-“Smart” Operation (Program Mode)

- Holiday Mode

- Settings

- Timer

Changing Network / disabling Wifi

You can move the heater to a new network if you need to. You will have to re-pair with the SmartLife app.

You can also de-activate and re-activate Wifi and revert to simple foot switch control. Long press the ‘-’button

on the receiver for 10 seconds to de-activate (blue Wifi LED goes out) and re-activate wifi (blue LED comes back

on).

Tap ‘+’ top right of App Select “Small Home Appliances”

and then “Thermostats”

If this is your first

thermostat you are

adding you will be asked

to enter your Wifi

password.

You will not have to do

this when you add

subsequent thermostats

to the App.

Activate the Power

switch on the heater

and then press the foot

switch until the power

signal light is on, the

Wi-Fi pairing indicator

will start to flash

rapidly.

Follow the instructions

on the App to pair.

If you failed to pair, click “Retry” in SmartLife App. Long press the “M” button (5) on the control box to reset the

pairing mode of the heater, following the directions in the SmartLife App.

In situations where several wifi connections are available and the heater fails to find the right router connection, we

recommend you try the Alternative Pairing mode offered by the SmartLife app. This is an option offered by the App

if normal pairing mode fails.

More detailed help is available online via the Help & Support section of your local Herschel Website.

Pairing

Select under desk heater

Override

You can always override the Programmed or Manual set temperatures to be higher or lower by using the + or –keys

on the App main screen to change the temperature. When operating on Smart mode, the heater will maintain the

override temperature until the next programmed period (when the next programmed temperature will be set).

Under Manual mode, the override temperature will remain set until you change it again manually.

Holiday Mode

There is also a Holiday mode which allows you to save energy by setting a lower temperature while you are away.

The Holiday mode has a day-counter feature allowing you to set the number of days you are away and return the

heating to normal operation ahead of your return.

Select Holiday mode by touching the “Holiday” icon on the App main screen. Select Days away using the slider and

set your holiday temperature using the + or –buttons. We recommend ending holiday mode at least one day before

your return to allow your house to warm back up again.

Settings

“Settings” on the App allow you to change the Smart mode program schedules and temperatures.

Timer

A timer function is available in 24 x 1hour increments. This turns the heater on for the specified number of hours.

The heater will only heat to the setpoint temperature.

Device Details

You can alter other details about your under desk heater including enabling Alexa or Google Assistant or sharing

control of your device with other members of your family by tapping the pencil icon at the top right of the App main

screen.

If you begin to use Smartlife to control other Home Automation devices, then you can also integrate your heater

control with other home automation tasks that you set up in SmartLife from the Device Details screen.

NOTE:

When restarting the heater after it has been switched off for any length of time, please give the heater time to re-

connect with your router before operating via the app. This can sometimes take afew minutes.

Smart mode

Your Herschel Select under desk heater heater works most efficiently when it is set up to run against a program

controlled by the SmartLife App. This program will always ensure your heater reaches the temperature you want at

the time you want it, each day of the week. This is represented by the “Smart” function on the App. So usually you

will want to set up and run the heater in Smart mode. To enable Smart mode touch the “Smart” icon on the App

main screen and alter the program settings in “Settings”.

Manual mode

Selecting Manual mode allows you to set and maintain a constant temperature that does not vary with the time of

day. Once you set a temperature using Manual mode, the under desk heater will maintain this temperature until

you give it another command. Select Manual mode by touching the “Manual” icon on the App main screen and alter

the temperature up or down using the + and –buttons.

Explanation of operating modes

Select under desk heater

General

Please note it is possible the heater may discolour with use –this is caused by airborne pollution and is

not a fault.

The heater is designed to last many years and incorporates several safety features, but if the heater has

not been used or installed in adherence to these instructions, emits any noise, smell, or shows rapid

discolouration of the surface, discontinue using the heater and refer to Herschel Customer Service or

your local Herschel dealer.

The Herschel panel must be installed, uninstalled, cleaned or transported only when cold.

Painting

The Select Under desk heater can be painted to match décor using a suitable heat resistant paint.

However, Herschel will not be responsible if the paint deteriorates or discolours. Any rights to return

the heater for a refund within statutory periods will be voided where the heater has been painted.

Painting the panel will not affect your warranty for repair or replacement.

Cleaning and maintenance

Cleaning

Before attempting to clean the panel, unplug the heater, isolate the unit from the electrical supply and

allow it to completely cool down.

DO NOT immerse the Herschel panel heater in water or splash water onto it.

Clean the heater with a damp cloth. For glass models glass cleaner can be used. Never use a wet cloth.

When clean, dry the surfaces with a dry cloth.

DO NOT apply abrasive materials, solvents or solvent wipes to the surface as this can cause irreparable

damage. Wait until the unit is completely dry before use.

Repair

DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit, doing so will void

your warranty. Repairs must only be carried out by Herschel or an authorised Herschel service partner.

Disposal

The heater is an electrical product and must not be disposed of in household waste. A high percentage

of the heater can be recycled. Please treat as electrical waste and recycle in accordance with local

regulations.

Autres manuels pour HS220UD

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Herschel Chauffage

Herschel

Herschel SUMMIT 2600 Manuel

Herschel

Herschel Inspire HB-750 Manuel

Herschel

Herschel HS500PR Manuel

Herschel

Herschel SUMMIT 2600 Manuel

Herschel

Herschel Select XLS Round XLS400RDW Manuel

Herschel

Herschel Krystal-600-B Manuel

Herschel

Herschel Select Series Manuel

Herschel

Herschel COLORADO 2500R Manuel

Herschel

Herschel HAWAII WAVE 2000 Manuel utilisateur

Herschel

Herschel MIAMI 2000 Manuel

Herschel

Herschel Select XLS500TB Manuel

Herschel

Herschel Select XLS300W Manuel

Herschel

Herschel CALIFORNIA 2000 Manuel

Herschel

Herschel HS220UD Manuel

Herschel

Herschel Inspire IP54 Manuel

Herschel

Herschel XLS500TW-INT Manuel utilisateur

Herschel

Herschel ASPECT XL2 Manuel

Herschel

Herschel MANHATTAN 3000 Manuel

Herschel

Herschel CALIFORNIA 2000R Manuel

Herschel

Herschel HS500PR Guide de configuration

Herschel

Herschel Vulcan 6S Manuel

Herschel

Herschel HAWAII WAVE Manuel utilisateur

Herschel

Herschel IR360 Manuel

Herschel

Herschel Inspire CL-200 Manuel

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur