hernest H200025 Manuel utilisateur
USER MANUAL
1
Caution
Please consu lt the professionals before installation or repairing. The company takes no liabilities for any damage or
injuries that occur during the installation of the pipes, floor, wall and tub.
Thank you for shopping with Hernest, please read this user manual thoroughly for your full under-
standing, installing, and application of the product. Please have this user manual well-reserved
for future reference.
Before Installation
Check the package and ensure that all parts are included. If any part is missing or damaged, please contact us.
Do not disassemble the main body, as it has been installed & commissioned correctly & precisely before leaving
the factory.
Shut off the main water supply before the installation.
Do flush the water supply lines to remove any dirt and debris before installation(IMPORTANT).
Make sure to connect the hot/cold inlet pipe correctly. If standing in front, usually the hot water pipe connects to
the left and the cold water pipe to the right.
Check for leaks and make sure every joint is safely sealed after the installation,
Turn on the water supply and flush the water pipes for 3 minutes to make sure it works well before putting it
into use.
SKU:H200025
Deck Mount Single Hole Faucet
General Info
In-put hosesC
Out-put hoseD
Pull-out hoseE
Weight locatorF
O-ringG
Plastic seat
Rubber gasketH
Steel gasketI
Fitting nutJ
Hot&cold water hosesK
2
ShankB
SpoutA
HandleL
HC
Hot Cold
Hot
Wall under sink
Cold
3
3Screw the fitting nut(J) on the shank(B)
under the deck tight, (you will still need
help or do it by yourself to keep the
faucet steady in this step).
You may need to screw the fitting nut(J)
many rounds in this step.
Please be patient and make sure the
handle(L) facing the direction you prefer
and fitting nut(J) locking tight, this
concerns the firmness of the faucet and
deck to be leak-proof;
4Turn off your kitchen hot&cold water
main valve;
Installation steps
Tools you will need
1Put O-ring, rubber gasket and deck plate(G,
H and I)in this order through the shank(B)
and four out-coming hoses(D, two of C and
E) from the shank.
2Install the shank(B) and put the four
out-coming hoses(D, two of C and E)
from the shank through the hole
reserved on your kitchen deck, hold the
faucet steadily(with help or by yourself)
for following steps.
G
B
J
J
E
Kitchen Deck
HC
Hot Cold
Hot
Wall under sink
Cold
HC
Hot Cold
Hot
Wall under sink
Cold
4
7Insert the tail of pull-out hose(E) into the
out-put hose(D) and maker sure the auto
lock is locked and you will hear a click if
it does.
8Install the weight locator(F) around the
upper side of the pull-out hose(E) (as
shown on page1). Make sure it pulls back
when you pull down the spout. This
component is to make sure the spout
goes back better when being pulled out.
But please also NOTE that if you install
the weight locator(F) too close to the
fitting nut(J), the reach will decrease;
9Turn the main valve on slowly to check if
any connecting part is not fastened to
avoid leaking. Then turn the handle(L)
on to check the waterways. If everything
goes well. the whole installation is
completed.
5Screw the connection nuts(the female side)
of cold&hot water hoses(K) to your kitchen
water source, fasten with an adjustable
wrench(not included in the package),
usually red for hot water on the left side,
and blue for cold water on the right;
6Screw the male heads of cold&hot water
hoses(K) to input hoses(C). there are
signs of cold and hot water entrance,
fasten with an adjustable wrench(not
included in the package). Please make
sure that the hot water way goes to the
hot signed input(C), and the cold goes to
the cold signed one;
For more detail information, please check out www.hernest.com
It will be our pleasure to have your visit.
After-Sale Service
If you have any issues with the product, please feel free to contact us online or by phone for customer service.
Phone No.: (909) 430-1666
5
www.hernest.com
Trouble Shooting
Leaking from faucet water
way(C and D)
Quick connect on output
hoses(D) may have been faulti-
ly installed.
Remove pull-out hose(C) from
output hose(D) and re-install.
make sure you hear a click
when you install it on the
output hose(D)
Hose does not retract Weight locator(F) may be
installed incorrectly
Readjust weight locator(F) on
the hose(E). Make sure it is
installed on the designated
mark on the hose(E)
Can't change water type or
changes incompletely
Spout switch may have some
malfunctions
Contact us to have a new spout
for replacement.
Low flow Sprout(A) may be clogged with
water dregs
Remove spout(A) from hoses.
Soak in 50/50 solution of warm
water and vinegar for 5
minutes then re-install it.
Issue Possible Causes Solutions
Table des matières
Autres manuels hernest Produits de plomberie
hernest
hernest H200228 Manuel utilisateur
hernest
hernest H200045 Manuel utilisateur
hernest
hernest H200202 Manuel utilisateur
hernest
hernest H200056 Manuel utilisateur
hernest
hernest H200020 Manuel utilisateur
hernest
hernest H200124 Manuel utilisateur
hernest
hernest H200037 Manuel utilisateur
hernest
hernest H200016 Manuel utilisateur
