Henny Penny 691 Mode d'emploi

Model 691

Power switch ON but fryer

completely inoperative

Pressure not exhausting at

end of cook cycle

Operating pressure too high

4-1. TROUBLESHOOTING GUIDE

Problem Cause Correction

•Open circuit

•Solenoid or exhaust line clogged

•Deadweight assembly clogged

•Plug fryer in

•Check breaker or fuse at wall

•Turn OFF and allow fryer to cool to

release the pressure in frypot; have

all lines, solenoid, and exhaust tank

cleaned

•Turn OFF and allow fryer to cool to

release the pressure in frypot; clean

deadweight per Section 3-15

DO NOT OPERATE UNIT IF PRESSURE GAUGE SHOWS HIGH-PRESSURE CONDITIONS.

SEVERE INJURIES AND BURNS WILL RESULT. PLACE THE POWER/PUMPSWITCH IN

THE OFF POSITION IMMEDIATELY. RELEASE THE PRESSURE BYALLOWINGUNIT

TO COOL. THE PRESSURE THEN DROPS. DO NOT RESUME USE OF UNIT UNTIL CAUSE

OF HIGH PRESSURE HAS BEEN FOUND AND CORRECTED.

Pressure does not build

Shortening not heating

Foaming or boiling over

Shortening not draining

Filter motor won’t run

•Not enough product in frypot

•Metal shipping spacer not

removed from deadweight

•Pressure not programmed

•Lid gasket leaking

•Gas valve knob turned to the

OFF position

•Drain valve open

•High temperature limit tripped

•See Boil-Over label on fryer

and information in this manual

•Drain valve clogged

•Motor overheated

•Place full capacity product in frypot

when using fresh shortening

•Remove shipping spacer; see

Section 2-2

•Check programming

•Reverse or replace lid gasket

•Make sure gas control valve knob is

turned to the ON position

•Close drain valve

•Reset high temperature limit

•Follow Boil-Over procedures

•Push cleaning rod through open

drain valve

•Reset motor

More detailed troubleshooting information is available in the Technical Manual, available at www.hennypenny.com,

or 1-800-417-8405 or 1-937-456-8405.

803 4-1

SECTION 4. TROUBLESHOOTING

Model 691

4-2. ERROR CODES In the event of a control system failure, the digital display will show

an error message which are coded: “E-4”, “E-5”, “E-6”, “E-10”,

“E-15”, “E-20A-D”, “E-41”, “E-46”, “E-47”, “E-48”, “E-70B”,

and “E-92”. A constant tone is heard when an error code is

displayed; and to silence this tone, press any of the product buttons.

DISPLAYCAUSE PANEL BOARD CORRECTION

“E-4” Control board Turn switch to OFF position, then turn switch back to ON;

overheating if display still shows “E-4”, the board is getting too hot; check

for signs of overheating behind the control panel; once panel

cools down, the controls should return to normal; if “E-4”

persists, replace the control

“E-5” Shortening Turn switch to OFF position, then back to ON; if display

overheating shows “E-5”, the heating circuits and temperature probe should

be checked; once the unit cools down, the controls should

return to normal; if “E-5” persists, replace the control

“E-6A” Temperature Turn switch to OFF position, then turn switch back to ON;

probe open if display shows “E-6”, have the temperature probe checked

“E-6B” Temperature Turn switch to OFF position, then turn switch back to ON;

probe shorted if display shows “E-6”, have the temperature probe checked

“E-10” High limit Reset the high limit by manually pushing up on the red reset

button; if the high limit does not reset, the high limit must be

replaced; call Henny Penny’s Service Department

“E-15” Drain switch Close the drain using the drain valve handle; if display still

shows “E-15”, call Henny Penny’s Service Department

“E-20A” Air pressure switch Press the timer button to try the ignition process again; and if

failure (stuck closed) “E-20A” persists, call Henny Penny’s Service Department

“E-20B” Draft fan or Press the Timer button to try the ignition process again; and if

air pressure “E-20B” persists, call Henny Penny’s Service Department

switch failure

(stuck open)

“E-20C” Ignition module Press the Timer button to try the ignition process again; and if

failure “E-20C” persists, call Henny Penny’s Service Department

“E-20D” Modules working Press the Timer button to try the ignition process again; and if

but no ignition “E-20D” persists, call Henny Penny’s Service Department

4-2 803

Model 691

803 4-3

4-2. ERROR CODES (Continued)

DISPLAYCAUSE PANEL BOARD CORRECTION

“E-41” Programming Turn switch to OFF position, then back to ON; if display

failure shows “E-41”, the control should be re-initialized (see Pro-

gramming section); if the error code persists, replace the

control panel

“E-46” Eeprom memory Turn switch to OFF position, then back to ON; if display

write error shows “E-46”, the control should be re-initialized (see Pro

gramming section); if the error code persists, replace the

control panel

“E-47” A-to-D failure Turn switch to OFF position, then back to ON; if display

(Analog converter shows “E-47”, the control should be re-initialized (see Pro-

chip) gramming section); if the error code persists, replace the

control panel

“E-48” Input system Turn switch to OFF position, then back to ON; if display

error (CPU can’t shows “E-48”, the control should be re-initialized (see Pro-

read buttons graming section); if the error code persists, replace the control

digital inputs) panel

“E-70B” Faulty power Have power switch checked, along with its wiring; have

switch, or switch Input/Output board replaced if necessary

wiring; faulty

I/O board

“E-92” 24-VAC fuse Have components, in 24-volt circuit (I.E., hi limit, drain switch)

on I/O board open checked for shorts

Model 691

4-4 803

THIS

PAGE

INTENTIONALLY

LEFT

BLANK.

Autres manuels Henny Penny Friteuse

Henny Penny

Henny Penny PFG-691 Manuel utilisateur

Henny Penny

Henny Penny EVOLUTION ELITE EEG-141 Manuel utilisateur

Henny Penny

Henny Penny F5 Manuel utilisateur

Henny Penny

Henny Penny 500 Manuel utilisateur

Henny Penny

Henny Penny 680 KFC Manuel utilisateur

Henny Penny

Henny Penny 500 Mode d'emploi

Henny Penny

Henny Penny CFE-415 Manuel utilisateur

Henny Penny

Henny Penny 690 Mode d'emploi

Henny Penny

Henny Penny Frontier UHC 600 Guide de référence

Henny Penny

Henny Penny F5 Manuel utilisateur

Henny Penny

Henny Penny 680 Manuel utilisateur

Henny Penny

Henny Penny 520 Manuel utilisateur

Henny Penny

Henny Penny LOV LVE-200 Series Manuel utilisateur

Henny Penny

Henny Penny 581 Manuel de programmation

Henny Penny

Henny Penny 8000 Computron Manuel utilisateur

Henny Penny

Henny Penny EVOLUTION ELITE Series Manuel utilisateur

Henny Penny

Henny Penny OFE-290 Manuel utilisateur

Henny Penny

Henny Penny OFE-322 Manuel utilisateur

Henny Penny

Henny Penny OFE-341 Mode d'emploi

Henny Penny

Henny Penny Evolution Elite EEE-141 Manuel utilisateur

Henny Penny

Henny Penny PFE-591 Manuel utilisateur

Henny Penny

Henny Penny LVE-202 Manuel utilisateur

Henny Penny

Henny Penny Evolution Elite Manuel utilisateur

Henny Penny

Henny Penny LVE-202 Manuel utilisateur

Manuels Friteuse populaires d'autres marques

Innsky

Innsky 55SA1US Manuel utilisateur

Falcon

Falcon G350/11 Guide de l'utilisateur

GoWISE USA

GoWISE USA GW22612 Manuel utilisateur

Wolf

Wolf IF15/S Manuel utilisateur

Electrolux

Electrolux Thermetic 9CHG583284 Guide rapide

Gourmia

Gourmia GAF799 Manuel utilisateur

DeLonghi

DeLonghi D677UX Manuel utilisateur

SEVERIN

SEVERIN DEEP FRYER - Guide de l'utilisateur

Toastmaster

Toastmaster TMFG18-NAT Manuel utilisateur

Domo

Domo DO465FR Manuel utilisateur

Farberware

Farberware FBW FT 43721 B Manuel utilisateur

GERMANICA

GERMANICA GEAF5L3LD Manuel utilisateur

Roller Grill

Roller Grill MF 120 R Manuel d'utilisation

Philips

Philips HD9211 Manuel utilisateur

Linea 2000

Linea 2000 Domo DO536FR Manuel utilisateur

Lakeland

Lakeland 31796 Manuel utilisateur

Dash

Dash Tasti-Crisp DFAF755 Manuel utilisateur

Fagor

Fagor F-200 Manuel utilisateur