5
Skew represents the dierence in propagation delay between the fastest and slowest set of wire pairs. A lower skew will mean
a longer video transmitting distance.
♦e maximum distance that supports cascading function for 720p & 1080i resolution is at 70 m. e maximum distance
without cascading function for 1080p resolution is at 30 m. However, with the use of Cat 6 HBT Cable, the max distance
for 1080p resolution can reach up to 60 m.
♦e FTP type of Cat5/5e/6 cable is recommended for some installations that might have the potential interference. e
RJ-45 terminations to the Cat5/5e/6 cable must be made to the EIA 568B specications. (See gure below)
♦Plug one end of the cable to the Transmitter’s “LINK IN/OUT” port and the other end to the Transceiver’s RJ-45 “LINK
IN/OUT” port. e monitor connected to the Transceiver should now display and the “LINK” LED should turn green to
indicate the DVI signal activation. Adjust the “EQ”control for best quality DVI display.
4. Extend Audio Signal:
e DAS-102T Transmitter and DAS-102TR Transceiver are not able to extend audio signals. Use a pair of DAS-AR Audio
Extenders with 4-wire phone cable and RJ-11 connectors to extend the audio.
5. Cascading additional Transceivers and Displays:
♦Cascading additional Transceivers to remote DVI-D displays is possible by using additional DAS-102TR Transceivers
and Cat5/5e/6 cable. Proper power grounding is a must for large group system cascading in order to prevent unpredicted
interferences
♦A DVI-D splitter or distribution amplier may be applied at each DVI-D output to broadcast additional local DVI-D
displays.
Installation and Operation
1. Install DAS-102T Transmitter :
♦First Time Set-up: Turn o the DVI output device (PC or DVD Player) and monitors.
♦Device Connection: Connect local DVI monitor (M1) to the “DVI/M1 OUT” of the transmitter and take the DVI-
HDMI cable, plug HDMI end to “INPUT” port of transmitter and the other end of the cable to PC/Player’s DVI-D video
port.
♦Connect the power adaptor to the “5VDC” and plug into the power outlet.
♦System Turn On: Turn on your DVI output device and monitor to conrm the functionality of the display. e “M1 LINK”
LED of the Transmitter should display orange to conrm the connection of a local DVI monitor.
♦Remote monitors: Make sure the remote monitor(s) to be connected to the DAS-102TR Transceiver can display the
broadcast video resolution.
♦EQ Adjustment: In most of the cases, you can adjust the EQ control to Auto mode by rotating the EQ control anti-
clockwise. e “EQ” and ”Auto”LEDs will display blue. If noise or an unstable image is seen on the local DVI monitor it
indicates the DVI signal received by the Transmitter needs to be adjusted. Adjust the EQ control for best image display
quality. e “EQ”and ”Auto” LEDs will turn o to indicate manual EQ mode.
♦EDID Simulation: e transmitter has built in an EDID simulator. When a local DVI monitor is connected to transmit-
ter it will automatically record the EDID data from the DVI monitor.When a local DVI monitor is not connected the
transmitter, it will simulate the EDID data and activate the DVI signal at the PC/player.
2. Install DAS-102TR Transceiver :
♦Connect DVI cable of DVI monitor to the receiver and turn on the monitor.
♦Plug power adaptor to DAS-102TR. At this time the “PWR” LED and “M1 LINK” should be on and the other “LINK”
LED should be o since there is no video signal input from “LINK IN” port.
♦If you see some dots or unclear image on the DVI monitor, the DVI signal received by Transmitter need to be adjusted. To
adjust image display to Auto mode, rotate the EQ to the left side.e “EQ” and “Auto” LEDs will display blue. Or you can
adjust the EQ control using the manual mode, the “EQ” and “Auto”LED will turn o to indicate the manual EQ mode.
3. Cat5/5e/6 Cable Connection:
♦Most makes and versions of current Cat5/5e/6 cables will work with the DAS-102T Transmitter and DAS-102TR Trans-
ceivers. However since the quality and characteristics of Cat5/5e/6 cable varies it has been found that some perform better
than others, even if they cost lower.e major factor inuencing the transmitting distance is the skew property of the cables.
DVI-D Transmitter
DVI to HDMI Cable
PDP LCD / TV Projector
DVI Projector and Monitor
PDP LCD / TV Projector
DVI Projector and Monitor
DVI-D Transceiver
DVI-D Transceiver DVI-D Transmitter
Cat-x Cable DVI to HDMI Cable
HDMI Player
HDMI Player
DVI-D Transceiver
DVI-D Transceiver DVI-D Transmitter
HDMI Player
Cat-x CableCat-x CableCat-x Cable DVI to HDMI Cable
1 2 3 4 5 6 7 8
JACK POSITION
PAIR 1PAIR 2 PAIR 4
PAIR 3
The EIA/TIA definition of 568B in the pin assignment
1. Orange White 2. Orange 3. Green White 4. Blue
5. Blue White 6. Green 7. Brown White 8. Brown
PDP LCD / TV Projector
DVI Projector and Monitor
PDP LCD / TV Projector
DVI Projector and Monitor
PDP LCD / TV Projector
DVI Projector and Monitor
PDP LCD / TV Projector
DVI Projector and Monitor
PDP LCD / TV Projector
DVI Projector and Monitor
