Heatstore HSDI330 Mode d’emploi

These instructions should be read carefully and

retained for future use. Note also the information

presented on the appliance.

Dynamic Intelirad Aluminium Radiator

Models: HSDI330 / HSDI500 / HSDI750 / HSDI1000

HSDI1500 / HSDI2000

OPERATING

INSTRUCTION MANUAL

08/53191/0 ISSUE 5

IMPORTANT

These instructions should be read carefully and retained for future use.

Note also the information presented on the appliance.

IMPORTANT SAFETY ADVICE

When using electrical appliances, basic precautions should always be followed to reduce

the risk of ﬁre, electrical shock, and injury to persons, including the following:

IMPORTANT – The wall bracket supplied with the appliance must be used.

WARNING - DO NOT USE THIS HEATER IN THE IMMEDIATE SURROUNDINGS OF

A BATH, A SHOWER OR A SWIMMING POOL.

IMPORTANT - If the heater is installed in a room containing a bath or shower, it must be

so installed that switches and other controls cannot be touched by a person using a bath

or shower.

Do not use outdoors.

Do not locate the heater immediately below a ﬁxed socket outlet or connection box.

CAUTION - Some parts of this product can become very hot and cause burns. Particular

attention has to be given where children and vulnerable people are present.This appliance

can be used by children aged from 8 years and above and by persons with reduced

physical, sensory or mental capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play with the appliance. Cleaning and

user maintenance shall not be made by children without supervision. Children of less

than 3 years should be kept away unless continuously supervised. Children aged from 3

years and less than 8 years shall only switch on/off the appliance provided that it has been

placed or installed in its intended normal operating position and they have been given

supervision or instruction concerning use of the appliance in a safe way and understand

the hazards involved. Children aged from 3 years and less than 8 years shall not plug in,

regulate and clean the appliance or perform user maintenance.

Note that due care and consideration must be taken when using this heater in series

with a thermal control, a program controller, a timer or any other device that switches

on the heat automatically, since a ﬁre risk exists when the heater is accidentally covered

or displaced. If the supply cord is damaged it must be replaced by the manufacturer or

service agent or a similarly qualiﬁed person in order to avoid a hazard.

WARNING - Servicing and product repairs should only be undertaken by the

manufacturers approved service agent or a similarly qualiﬁed person, using only exact

manufacturer approved spare parts.

WARNING - In order to avoid overheating, do not cover the heater. Do not place material

or garments on the heater, or obstruct the air circulation around the heater, for instance

by curtains or furniture, as this could cause overheating and a ﬁre risk. NEVER cover or

obstruct in any way the heat outlet slots at the top of the heater or the air inlet slots in the

base of the heater.

The heater carries a warning ‘DO NOT COVER’ to alert the user to the risk of ﬁre that

exists if the heater is accidentally covered.

WARNING - THIS APPLIANCE MUST BE EARTHED

The electrical installation must be carried out by a competent electrician, and be in strict

accordance with the current I.E.E. Regulations for Electrical Equipment in Buildings.The

wires in this mains lead are coloured in accordance with the following code:

GREEN AND YELLOW: EARTH

BLUE: NEUTRAL

BROWN: LIVE

The heater is ﬁtted with a length of ﬂexible cable type H05VV-F size 3 x 1.0mm2for

connection to the ﬁxed wiring of the premises through a suitable connection box

positioned adjacent to the heater. A means for disconnection must be incorporated in

the ﬁxed wiring of the premises in accordance with the wiring rules. The supply circuit to

the heater must incorporate a double pole isolating switch having a contact separation

of at least 3mm.

Supplementary Earth Bonding

Should Equipotential Earth Bonding be required the earthing conductor in the supply

cord is deemed to provide the supplementary bonding connection (see Regulation

544.2.5, 17th Edition I.E.E. Wiring Regulations).

Please note that lit cigarettes, candles and oil burners, combined with the convection

effect of electric heaters can cause soot deposits to build up on the surface directly

above and to the sides of the heater. This is not a fault of the heater. Extensive burning

of candles or smoking in the operating environment of this product can produce heavy

discolouration within a few months of use.

This heater is ﬁlled with a precise quantity of special oil. Repairs requiring opening of the

oil container are only to be made by the manufacturer or his service agent who should be

contacted if there is an oil leakage.

Regulations concerning the disposal of oil when scrapping the appliance have to be

followed.

Safety - Overheat protection

For your safety this appliance is ﬁtted with a thermal cut-out. In the event that the

product overheats for some reason, the cut-out prevents excessive temperatures on the

product by cutting the power to the heater. Once the heater has cooled down, it will

reset automatically, it will continue to cycle on and off automatically until the reason for

overheating is removed. The display screen may ﬂash red to indicate the product has

overheated.To reset the display, remove the obstruction and hold Enter for 10 seconds.

Contents

Wall Mounting

Operation

Control Functions

Setting the Date and Time

Energy Saving Tips

Main Screen

Modes of Operation

Important

General

8Quick Start Guide

Choosing and Setting a Mode

14 Advance

Boost

Options

Child Lock

User Information

User introduction

Thank you for choosing the Heatstore Dynamic Intelirad Aluminium Radiator.We manufacture

the highest quality heating products for use in a wide variety of environments. This product

has been designed to incorporate the latest, most advanced technologies to give you

maximum control over your heating. The product allows for the simple setting of required

time and temperature, and includes many energy-saving features which work automatically

to help keep you warm for less.

Please read the instructions closely before ﬁrst using the product, there is also quick-start

guide on the next page if you need a reminder of how to use the basic functions in the

future.

Inteli - Energy saving features

The Intelirad Aluminium Radiator has many features which are designed to save you

money. It has a self-learning capacity, constantly monitoring the effect that its actions have

on the room temperature. This means that your heater knows how long it will take to get

to a certain temperature, or when to turn off as it approaches a comfortable temperature.

This minimises the energy that it uses whilst maximising comfort, keeping you warm for

the lowest possible cost.

Inteli - Aluminium n technology

The Intelirad Aluminium Radiator incorporates ﬁn technology that optimises the heat

distribution and reduces the warm up time.

Inteli - Open window technology

Should a window or door be accidentally left open, your heater will detect the change in

temperature and go into a standby mode, returning to normal operation when the window

or door has been closed. This stops the heater from trying to warm the room while heat is

escaping from it, saving you money.

Inteli - EcoStart (anticipatory control)

Having learnt how quickly it can heat up your room, the Intelirad Aluminium Radiator is able

to turn on at just the right time in order to get the room up to a comfortable temperature

when you want it. For example, if you get up at 7am, you would normally have to guess

when to turn the heating on in order for it to pre-heat the room in time. Depending on how

cold it is outside, this could mean the room is still cold when you have to get out of bed, or

mean that its been warm for half an hour before it needed to be. Inteli EcoStart means that

if you select 21 degrees celsius at 7am, the heater will turn on exactly when it needs to to

meet this target, running for shorter periods of time when the weather is mild, and ensuring

the room is nice and warm in the winter.

These functions are explained in more detail later, and can be disabled if the environment that the

heater is installed into means that they are not needed.

The heater is designed for wall mounting using the wall bracket supplied. It should only be

operated when in the upright position as shown - see Fig. 1 and Fig. 2. All models are splash

proof to IP24 standard and may be used in bathrooms, however not in the immediate vicinity

of baths, showers, water connections, wash basins or swimming pools. Before connecting

the heater check that the supply voltage is the same as that stated on the heater.

IMPORTANT - The wall bracket supplied with the appliance must be used.The heater should

be positioned observing the minimum clearances stated around the heater - see Fig. 1 and

Fig. 2.

DO NOT locate the heater immediately below a ﬁxed socket outlet or connection box.

1. Remove wall mounting brackets from the protective packaging and locate the wall

mounting template.

2. Using the template, drill and plug the mounting holes speciﬁc to your particular model

- see Fig. 3.

3. Fix the top wall mounting brackets securely to the wall using the screws provided.

4. The bottom wall mounting brackets should be clipped onto the product prior to

mounting the product to the wall.

5. The product can now be hung on the top wall mounting bracket then ﬁxed in place by

securing the bottom wall bracket(s) in place.

General

Wall Mounting

Dimensions

Model(s) Watt (kW) A (mm)

HSDI330 0.33 kW 348

HSDI500 0.50 kW 508

HSDI750 0.75 kW 588

HSDI1000 1.0 kW 668

HSDI1500 1.5 kW 908

HSDI2000 2.0 kW 1068

Fig. 2Fig. 1

150 mm (Min)

150 mm

(Min)

570 mm

A mm

115 mm

Shelf

300 mm

Fig. 3

Template

Timer Modes

Your Heatstore Intelirad

Aluminium Radiator comes

pre-programmed with four timer

modes. These modes deﬁne the

periods when the heater will

operate in Comfort On mode.

The four modes are:

This guide is for quick reference only.

Please refer to the operating section for further information.

How Does the Heater Control Work?

The control allows you to choose when you want heat and at what temperature.

When using a timer mode (see below), Comfort On will display on the home screen to tell

you when the heater is maintaining the temperature displayed. Comfort O will display

when the heater is outside of a timed heating period. When Manual, Eco or Frost modes

are being used the heater will always maintain the temperature shown on the home screen.

Set the Time

To set the date and time on the heater, press Menu, then press the Enter with Time / Date

highlighted. Press or until the correct value is shown, then press Enter to conﬁrm and

move on to the next value. Repeat until all details are correct, and Set displays, then press

Back.

The time is automatically adjusted in spring and autumn between Greenwich Mean Time

(GMT) and British Summer Time (BST).

Set the Temperature

The temperature shown on the display is the room temperature set point. This is the

temperature that the heater will maintain during the heating periods. If the room temperature

is above this temperature then the heater will not operate.The heater leaves the factory with

this temperature set at 21°C which represents a typical, comfortable room temperature. If

you require a different room temperature then press either or until the display shows

the temperature you require.

Quick Start Guide

Child Lock

If you need to lock the controls so that the settings

cannot be changed then activate the Child Lock.

To lock the controls press and hold both the Back

button and Enter for three seconds. Child Lock

will appear at the bottom of the screen.To unlock

the control repeat the action by pressing both the

Back button and Enter for three seconds.

Timer Mode Description

Out All Day 6 hours heating per day in two

periods

Home All Day 13 hours heating per day in one

period

Holiday Set the temperature and number of

days for which you are on holiday

User timer Customise times in four periods

Child Lock

Comfort o

12:00

Which Timer Mode is Best for Me?

The heater leaves the factory set in Out All Day mode. If you are out during the day and only

require heat in the mornings and evenings then this mode will suit your lifestyle and you

won’t need to alter anything. If you are in during the day then you should select the Home

All Day mode which is a single heating period. The User Timer mode will give you four

periods of heating split throughout the day. If you are away for an extended period then you

can use the Holiday mode. This allows you to reduce the heating during the period that you

are away, reverting to the previously selected mode on the day you return.

Advance

Sometimes you may be at home when you

had not planned to be, or need to leave

when you had planned to have the heating

on. You can change the way you use your

heating temporarily, this temporary change

is achieved by using the Advance function.

When a timer has been selected, the Advance

function allows you to begin the next period

early. If the heater is in a Comfort O period

and you want heat - press the Advance

button. If the heater is in Comfort On and

you don’t want heat, press the Advance

button and it will go off until the beginning

of the next Comfort On period.

Advance Boost

The Advance button is also used to enter

the boost mode which provides temporary

heating for one, two, three or four hours.

Press the Advance button twice to begin

a one hour boost. Continue pressing the

Advance button to enter the longer boost

periods.

Main Menu

Date / Time

Options

Mode

Timer Mode

Eco Mode

Standby

Frost Protect

Manual

Timer Mode

Out All Day

Holiday

User Timer

Home All Day

Out All Day

Preview

Select

Modify

Out All Day

Select

Comfort o

12:00

To choose a timer mode press Menu followed

by Enter to select Timer Mode. Select the

mode required by pressing or and then

Enter. For options Out All Day, Home All Day

and User Timer, three choices are available

Select, Preview and Modify.

Select - Choose this timer option

Preview - View the times currently set

Modify - Change the times currently set

Please refer to page 14‘Choosing and Setting

a Mode’ in these operating instructions

for information on how to modify the

programmed times.

The controls are located on the top right of the heater.The heater is ﬁtted with an adjustable

electronic controller consisting of a display screen and six touch buttons.

The heater is ﬁtted with a highly accurate

electronic thermostat incorporating

Dynamic Efﬁciency + technology. With an

accuracy of just 0.2°C enabling the room

temperature to be controlled. The minimum

room temperature is 7°C. The maximum

temperature is set to 26°C by default

however this can be increased to 32°C if

required. A temperature of 21ºC represents

a normal room temperature.

1Display Screen

2‘Menu’ Button

3‘Back’ Button

4‘Up and Down’ Arrows

5‘Enter’ Button

6Heating Status

7‘Advance’ Button

Operation

NOTE:

Should the heater not operate, this may be

due to the room temperature being higher

than the thermostat setting.

Comfort O

12:00

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Heatstore Chauffage

Heatstore

Heatstore HSCF3000E Manuel d'utilisation et d'entretien

Heatstore

Heatstore HSQH3000 Manuel utilisateur

Heatstore

Heatstore HSDS Manuel utilisateur

Heatstore

Heatstore HSCEH7115N Manuel

Heatstore

Heatstore HSACW9000 Manuel

Heatstore

Heatstore HSAC6000X Manuel

Heatstore

Heatstore Frost Guard HSMP05 Manuel utilisateur

Heatstore

Heatstore HSCPF3000 Manuel

Heatstore

Heatstore HSAC3000X Manuel

Heatstore

Heatstore HS2000X Manuel utilisateur

Heatstore

Heatstore HSRCH4500RF Manuel utilisateur

Heatstore

Heatstore HSCVDURF Manuel d'utilisation et d'entretien

Heatstore

Heatstore DYNAMIC HSDR500T Mode d'emploi

Heatstore

Heatstore HSCFH60WX Manuel utilisateur

Heatstore

Heatstore HSPBRF Manuel utilisateur

Heatstore

Heatstore HSAC9000X Manuel

Heatstore

Heatstore HS2000T Manuel utilisateur

Heatstore

Heatstore HSXCA12X Manuel utilisateur

Heatstore

Heatstore Dynamic InteliPlinth HSDBU24 Manuel utilisateur

Heatstore

Heatstore HS2000X Manuel utilisateur

Heatstore

Heatstore HSACR X Series Manuel utilisateur

Heatstore

Heatstore HSP500WRF Manuel d'utilisation et d'entretien

Heatstore

Heatstore HSDHHR070 Manuel utilisateur

Heatstore

Heatstore HS2020XCN Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur