2
intelliGen Field Mount (iFM) Kits for
Unit Coolers
The intelliGen™Field Mount Kit is designed to install in the
field for new unit coolers without factory mounted controls
or retrofit of existing unit coolers with mechanical control
to upgrade to electronic control. The intelliGen control can
be remote mounted up to 40 feet from the unit cooler at a
convenient location for easy access. The intelliGen control is
pre-assembled in a IP65 rated housing for both indoor and
Components Needed for Installation
The iFM kit comes with the intelliGen controller, 3 tempera-
ture sensors, 1 pressure transducer with cable, 1 terminal
board and mounting accessories. The temperature sensors
and pressure transducer cable are 25 feet in length. Other
wire lengths are available as optional kit in separate part
numbers. See Components Included section for details.
There are individual system dependent components are
not included but required for each installation. These
components include the 24VAC control power transformer,
the electronic expansion valve (EXV), the power wires for
control power, fan motors, defrost heaters and solenoid
outdoor applications. It supports Heatcraft’s major unit cooler
product lines such as the Low Profile, Center Mount and
Low Velocity Center Mount, Medium Profile, High Profile
Large Unit Coolers and others. It is universal fit for field
mount and retrofit for all air and electric defrost unit coolers
for refrigeration.
valve. Not all applications require defrost heaters and solenoid
valve, check the system requirement for wiring needs.
See Components NOT Included section for details and avail-
ability options.
Field wire runs between the intelliGen controller and the unit
cooler should be in conduits and have to meet local building
and electric code requirements. Conduit fittings are needed
for the conduit runs. Please conduct a site survey and review
your local codes for detailed requirements prior to installation.
Low voltage and communication wires need to run in separate
conduit from the high voltage wires to minimize interference.
Field Mount Kit Includes
Pre-Assembled, Wall-Mount
Controller Assembly
- intelliGen™ main control board and
display board inside water resistant
plastic housing with connection cable
3X Temperature Sensors (with 25ft leads)
Pressure Transducer with Harness (25ft)
Terminal Board with Screws
and Accessories
Easy-to-Follow Wiring Diagram
User Manual
intelliGen™ controllers are the simple,
intuitive alternative for refrigeration control.
Easy-to-read 3-color LED status bar
Text message display
Easy setup and no more service codes to look up
Simple turn & press navigation knob
Optional webserver and integration cards
One per system, supports up to 8 unit-coolers
Free remote monitoring with webserver upgrade*
Energy-saving Smart Defrost
* Requires optional intelliGen Webserver card or BMS integration card. FPO FOR FINAL LEGAL Lorem ipsum dolor sit amet, consectetuer adipiscing elit,
tincidunt ut laoreet dolore magna aliquam erat volutpat. Ut wisi enim ad minim veniam, quis nostrud exerci tation ullamcorper suscipit lobortis nisl ut
aliquip ex ea commodo consequat. Duis autem vel eum iriure dolor in hendrerit in vulputate velit esse molestie consequat, vel illum dolore eu feugiat
nulla facilisis at vero eros et accumsan et iusto odio dignissim qui blandit praesent luptatum zzril delenit augue duis dolore.
Universal Field-Mount
Refrigeration Controller
with temperature sensors and pressure transducer kit
Simple setup
with intelliGen™
Quick Start
Intuitive and
easy to use
user interface
On board
USB port for
data logging and
software update
Remote
monitoring
with optional
webserver card*
Support up to
8 unit coolers in a
single system
Connect. Control. Diagnose. Relax.
Scan the QR Code
or visit
intelliGenControls.com
User-friendly
interface for easy
install and service.
Quick Start system
configuration allows for
setup in minutes, not hours.
Light Bar Alerts
Color coded LED immediately
shows the status of your system.
Full-Text Display
Guided text instruction
for setup and service.
Quick Menu Buttons
Establish preferred settings
and quickly make changes.
Turn & Press Knob
Quickly navigate system
configuration and servicing.
Ready-to-Mount
Plastic Housing
Waterproof seal for indoor &
outdoor applications.
All electronics pre-installed.
Reduce diagnosis, service
and downtime with intuitive
user interface, data logging
and optional remote monitoring.
The intelliGen™ Field Mount kit
is the simple, easy-to-install
solution for remote refrigeration
monitoring and control.
HARNESS
Sensor Harnesses (X3)
Pressure Transducer
Harness (X1)
ACCESSORIES
Screws and
Installation
Accessories
CONTROLLER
intelliGen™ Controller
Pre-Installed in IP64
Water-Resistant Case
ICON
TO
COME
IMPORTANT!
Additional components are required for
proper iFM installation. Be sure you have
compatible version of the following parts.
Recommended Tools for Installation
Scan QR Code for details and
to view our installation video
or visit
intelliGenControls.com
24VAC Transformer
EEV Kit with Cable
High Voltage Control Harness
Uni-bit
Power drill & drill bits
5/16” nut driver
7/16” & 5/8” wrenches
Phillips screwdriver
Precision slotted screwdriver
Wire Stripper/Crimper
Multimeter
intelliGen Field Mount (iFM) Kits
