Health Master HM-U6200 Manuel utilisateur

OWNER’S

MANUAL

Exercise can present a health risk. Consult a physician before beginning any exercise program

with this equipment.

If you feel faint or dizzy, immediately discontinue use of this equipment. Serious bodily injury

can occur if this equipment is not assembled and used correctly. Serious bodily injury can also

occur if all instructions are not followed.

Keep children and pets away from equipment when in use. Always make sure all bolts and nuts

are tightened prior to each use. Follow all safety instructions in this manual.

CAUTION: WEIGHT ON THIS PRODUCT SHOULD NOT EXCEED 136KG / 300LBS.

VERSION: V. III

Product May Vary Slightly From Picture

MADE IN TAIWAN

“SAFETY INSTRUCTION”

WARNING: To reduce the risk of serious injury, read the following safety instructions before using the

URIGHT BIKE

1. Read all warnings posted on the equipment

2. Read this Owner's Manual and follow it carefully before using the equipment. Make sure that it is properly assembled and tightened

before use

3. We recommend that two people be available for assembly of this product

4. Keep children and pets awayfrom the equipment. Do not allow children and pets to use or play on the equipment .Always keep children

and pets away from the equipment when it is in use

5. It is recommended that you place this exercise equipment on an equipment mat

6. Set up and operate the equipment on a solid level surface. Do not position the equipment on loose rugs or uneven surfaces

7. Inspect the equipment for worn or loose components prior to each use

8. Tighten / replace any loose or worn components prior to using the equipment

9. Consult a physician prior to commencing an exercise program. If, at any time during exercise, you feel faint, dizzy, or experience pain,

stop and consult your physician

10. Follow your physician's recommendations in developing your own personal fitness program

11. Always choose the workout which best fits your physical strength and flexibility level. Know your limits and train within them. Always use

common sense when exercising

12. Before using this product, please consult your personal physician for a complete physical examination.

13. Do not wear loose or dangling clothing while using the equipment

14. Never exercise in bare feet or socks; always wear correct footwear, such as running, walking, or cross-training shoes

15. Be careful to maintain your balance while using, mounting, dismounting, or assembling the equipment loss of balance may result in a fall

and serious bodily injury

16. Keep both feet firmly and securely on the Foot Pedals while exercising

17. The equipment should not be used by persons weighing over 300 pounds /136 kgs

18. The equipment should be used by only one person at a time

19. The equipment is for semi-commercial, light-commercial and home usage

20. Maintenance: Replace the defective components immediately and / or keep the equipment out of use until repair the equipment

completely.

21. Make sure that adequate space is available for access to and passage around the equipment; keep at least a distance of 1 meter from

any obstruction object while using the machine

WARNING: Before starting any exercise or conditioning program you should consult with your personal physician to see if you require a

complete physical exam. This is especially important if you are over the age of35, have never exercised before, are pregnant, or suffer from

any illness

READ AND FOLLOW THE SAFETY PRECAUTIONS. FAILURE TO FOLLOW THESE

INSTRUCTIONS CAN RESULT IN SERIOUS BODILY INJURY

“ASSEMBLY PARTS”

Unpack the box in a clear area. Follow the List of Assembly Parts below to check and make sure all assembly parts are

present and in good condition. Do not dispose of the packing material until the assembly process is completed. Assembly

tools and hardware kit have included for you to use when assembling the product

Console Upper Cover Console Bottom

Cover Console Sleeve Upright Post Assembly

Front Handlebar Upright Sleeve Main Frame Assembly

Front Stabilizer Rear Stabilizer Pedal

“HARDWARE IDENTIFICATION CHART”

Unpack the box in a clear area. Follow the List of Hardware Kit below. This chart is provided to help identify the hardware

used in the assembly process. Place the washers, the end of bolts, or screws on the circles to check for the correct

diameter. User the small scale to check the length of the bolts and screws. Do not dispose of the packing material until the

assembly process is completed

NOTICE: The length of all bolts and screws except those with flat heads is

Measured from below the head to the end of the bolt or screw. Flat head

bolts and screws are measured from the top of the head to the end of the

bolt or screw

After unpacking the unit, open the hardware bag and make sure that you have all the following items. Note: Some small

parts may have been pre-attached for shipping. If a part is not in the hardware bag, check to see if it has been

pre-assembled

Part No. and Description Q’TY

65 Lock Washer (M8) 9 pcs

66 Washer (8x16x2.0t) 9 pcs

72 Screw, Pan Head (M5xp0.8x25mm) 4 pcs

73 Screw, Round Head (M5xp0.8x15mm) 4 pcs

81 Bolt, Socket Head (M6xp1.0x15mm)

82 Bolt, Socket Head (M8xp1.25x16mm)

83 Bolt, Socket Head (M8xp1.25x45mm)

84 Bolt, Socket Head (M8xp1.25x90mm)

4 pcs

1 pcs

4 pcs

THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY:

MULTI WRENCH TOOL W/

PHILLIPS SCREWDRIVER

(13 & 15mm)

ALLEN WRENCH

(5 & 6 mm)

“BEFORE YOU BEGIN”

Thank you for choosing the UPRIGHT BIKE. We

take great pride in producing this quality product and

hope it will provide many hours of quality exercise to

make you feel better, look better and enjoy life to its

fullest.

Yes, it's a proven fact that a regular exercise

program can improve your physical and mental health.

Too often, our busy lifestyles limit our time and

opportunity to exercise. The equipment provides a

convenient and simple method to begin your assault

on getting your body in shape and achieving a

happier and healthier lifestyle.

Before reading further, please review the drawing

below and familiarize yourself with the parts that are

labeled. Read this manual carefully before using the

equipment.

Console

Front Handlebar

Console Sleeve

Upright Post

Upright Sleeve

Seat Post Adjusting

Handle

Front Stabilizer

Pedal

Adjustable Rear Stabilizer EndCap

Seat Cushion

Seat Cap

Rear Stabilizer

Main Frame

Hand Pulse

Sensor

“ASSEMBLE INSTRUCTIONS”

STEP 1– Stabilizer Assembly

a. Identify the correct direction of the Front Stabilizer (2), there is an “R” decal on the right side of the Front Stabilizer

(2)

b. Attach the Front Stabilizer (2) to the Main Frame (1) and secure with two Lock Washers (M8)(65), two Washers

(8x16x2.0t)(66) and two Bolts, Socket Head (M8xp1.25x90mm)(84)

c. Fully secure two Lock Washers (M8)(65), two Washers (8x16x2.0t)(66) and two Bolts, Socket Head

(M8xp1.25x90mm)(84) that attach to the Front Stabilizer (2) to the Main Frame (1)

d. Follow the above STEP b. to attach the Rear Stabilizer (3) to the Main Frame (1) with two Lock Washers (M8)(65),

two Washers (8x16x2.0t)(66) and two Bolts, Socket Head (M8xp1.25x90mm)(84).

NOTE: “Small Tip: Attach screws and bolts to the assembly parts first before secure”

To assemble the Front Stabilizer (2) to the Main Frame (1) with more efficient and easy way, it is suggested to

attach two Lock Washers (M8)(65), two Washers (8x16x2.0t)(66) and two Bolts, Socket Head

(M8xp1.25x90mm)(84) to the Front Stabilizer (2) and the Main Frame (1) first before fully secure. **Please do

not secure the bolts unless you make sure Bolts all go into screw holes of Front Stabilizer and Main

Frame**

“ASSEMBLE INSTRUCTIONS” STEP 2– Upright Post Assembly

a. Slide the Upright Sleeve (26) onto the Upright Post

Assembly (5) Be care not to pinch the wires

b. Attach the Upright Post Assembly (5) to the Main

Frame (1) with four Washers (8x16x2.0t)(66), four

Lock Washers (M8)(65), four Bolts, Socket Head

(M8xp1.25x16mm)(82)

c. Fully secure four Washers (8x16x2.0t)(66),

four Lock Washers (M8)(65), and four Bolts,

Socket Head (M8xp1.25x16mm)(82) that

attach to the Upright Post Assembly (5) and

the Main Frame (1).

d. Connect the Rear Connection Wire (95A) to the

Motor Wire (98). Be care not to pinch the wires.

e. Connect the Rear Connection Wire (95B) to the

Adaptor Connection Wire (96). Be care not to

pinch the wires

f. Connect the Rear Connection Wire (95C) to the

Sensor Wire (99). Be care not to pinch the wires

g. Slide the Upright Sleeve (26) down until it meets the

Main Frame (1).

STEP 3– Front Handlebar Assembly

a. Remove four Washers (8x16x2.0t)(66), four Lock Washers (M8)(65) and four Bolts, Button Head

(M8xp1.25x16mm)(79) from the side of the Front Handlebar (6)

b. Position the Front Handlebar (6) in place through the Upright Post Assembly (5) and secure with five Washers

(8x16x2.0t)(66), five Lock Washers (M8)(65), four Bolts, Button Head (M8xp1.25x16mm)(79) and one Bolt, Socket

Head (M8xp1.25x45mm)(83) NOTE: One Washer (8x16x2.0t)(66), one Lock Washer (M8)(65), one Bolt, Socket

Head (M8xp1.25x45mm)(83) will be packed into the hardware bag

c. Fully secure five Washers (8x16x2.0t)(66), five Lock Washers (M8)(65), four Bolts, Button Head

(M8xp1.25x16mm)(79) and one Bolt, Socket Head (M8xp1.25x45mm)(83) that attach to the Front Handlebar(6) and

the Main Frame (1).

NOTE: “Small Tip: Attach screws and bolts to the

assembly parts first before secure” **Please do not

secure the bolts unless you make sure 4pcs

Washers, Lock Washers and Bolts all go into screw

holes of Upright Post Assembly and Main Frame**

NOTE: “Small Tip: Attach screws and bolts to the assembly parts first before secure”

**Please do not secure the bolts unless you make sure Bolts all go into screw holes of Front Handlebar and

Upright Post Assembly**

NOTE: After connecting the wires, slightly and gently pull

two sides of wires to test and make sure whether the wires

are fully connected.

“ASSEMBLE INSTRUCTIONS”

STEP 4– Console Assembly

a. Follow FIG.1 to attach the Console Bottom Cover (33) to the Console Upper Cover (32) and secure with four

Screws, Pan Head (M5xp0.8x25mm)(72)

b. Place and secure the Console Assembly (32, 33) onto the iron plate of the Upright Post Assembly (5) using four

Bolts, Socket Head (M6xp1.0x15mm)(81).

c. Fully secure four Bolts, Socket Head (M6xp1.0x15mm)(81) that attach to the Console(32,33) and the Upright Post

Assembly(5).

d. Connect the Front Connection Wire (94) to the Rear Connection Wire (95). Be care not to pinch the wires

e. Connect the Front Pulse Sensor Wire (100) to the Rear Pulse Sensor Wire (101). Be care not to pinch the wires

NOTE: After connecting the wires, slightly and gently pull two sides of wires to test and make sure whether the

wires are fully connected.

NOTE: “Small Tip: Attach screws and bolts to the assembly parts first before secure”

**Please do not secure the bolts unless you make sure Bolts all go into screw holes of Console and Upright

Post Assembly**

“ASSEMBLE INSTRUCTIONS”

STEP 5– Console Sleeve Assembly

a. Attach the Right Console Sleeve (35) to the right side of the Upright

Post Assembly (5) NOTE: Make sure that the Right Console

Sleeve (35) would cover the right side of the Upright Post

Assembly (5) , lowest layer of

the Console Button Cover

(33) and the right side of the

Front Handlebar (6) as the

illustrator shown on the left

b. Then secure the Right Console Sleeve (35) to the Upright Post Assembly (5)

with two Screws, Round Head (M5xp0.8x15mm)(73)

c. Repeat the above process on the left side to attach the Left Console Sleeve

(34) to the left side of the Upright Post Assembly (5) NOTE: Make sure that

the Left Console Sleeve (34) would cover the left side of the Upright Post

Assembly (5), lowest layer of the Console Button Cover (33) and the left side

of the Front Handlebar (6) as the illustrator shown on the left

“ASSEMBLE INSTRUCTIONS”

STEP 6– Pedal Assembly

a. Thread the Right Pedal (11) into the right crank area of the Main Frame (1). Firmly tighten the Right Pedal (11)

clockwise into the right crank. Tighten the Pedal as firmly as possible

b. Thread the Left Pedal (10) into the left crank area of the Main Frame (1). Firmly tighten the Left Pedal (10)

counter-clockwise into the left crank. Tighten the Pedal as firmly as possible

c. Finish the assembly, make sure that all parts are tightened before you use the equipment

Table des matières

Manuels vélo d'appartement populaires d'autres marques

Weslo

Weslo Vector 302 Guide de démarrage rapide

TOORX

TOORX BRX85 Manuel utilisateur

Matrix

Matrix KranKcycle Manuel utilisateur

Matrix

Matrix IC3 Manuel utilisateur

Sunny Health & Fitness

Sunny Health & Fitness SF-B121021 Manuel utilisateur

Monark

Monark 827E Manuel utilisateur

Stamina

Stamina 1310 Manuel utilisateur

American Fitness

American Fitness SPR-BK1072A Manuel utilisateur

Cateye

Cateye CS-1000 (CYCLO SIMULATOR) Manuel utilisateur

BH FITNESS

BH FITNESS H9158H Manuel de l'opérateur

Body Sculpture

Body Sculpture BC-7220G Manuel utilisateur

Cateye

Cateye EC-2300 Manuel utilisateur

FYTTER

FYTTER RACER RC MSR Manuel utilisateur

Kikos

Kikos HM-9090M Manuel utilisateur

Pro-Form

Pro-Form 345 Zlx Bike Guide de l'utilisateur

Fuel Fitness

Fuel Fitness SU135-40 Manuel utilisateur

NordicTrack

NordicTrack Gxr 4.2 Bike Manuel utilisateur

Vision Fitness

Vision Fitness U70 Manuel utilisateur