Heads Up Technologies XMR100 Manuel utilisateur

H E A D S U P T E C H N O L O G I E S

XM RADIO SYSTEM

COMPONENT INSTALLATION MANUAL

Model Numbers: XMR100, XMR200, XMR400, XMR800, XMC100, XMRANT

Revision Level: C

Revision Date: 04/05/06

Document Control No.: XMR-3

Approvals:

Author:

J. Header, Engineering

Checked:

M. Wootton, Engineering

Approved:

D. Groos, Marketing

Heads Up Technologies, Inc.

2033 Chenault Dr., Suite 100

Carrollton, Texas 75006

XM Radio

Installation Manual

XMR-3

Rev. C, 04/05/06 Page 2 of 31

H E A D S U P T E C H N O L O G I E S

REVISION HISTORY

Revision Change Date Description of Change

- 06/04/03 Initial Release

A 06/09/03 PG 12: Changed warranty period from 1 to 2 years.

B 01/08/04 Added reprogramming jack installation information.

Added XMC-3A drawing to applicable documents

section.

C 04/05/06 Added description and use information for the

discrete inputs of the XMRX00 per ECN 894.

Removed “max” current ratings since they are not

needed for the aircraft load analysis. Corrected audio

output level and added volume adjust range spec.

Added SAT RF specs.

Reworded several sections for clarity and

compatibility with Ver 1.13 or later software. Added

multi-receiver information to Section 3.2.

Added disable announcements description, audio

wiring details, antenna installation considerations.

Added Maintenance section including

troubleshooting matrix, system info, etc.

Replaced all information related to ‘40-ft max or

11dB max cable antenna loss’ to specifying ‘22dB

(+/-2dB)’ gain to the receiver input and added some

common cable type reference information.

Added pre-activation note. Changed listed part

numbers on title page to specific model nos.

XM Radio

Installation Manual

XMR-3

Rev. C, 04/05/06 Page 3 of 31

H E A D S U P T E C H N O L O G I E S

TABLE OF CONTENTS

1.0 INTRODUCTION ........................................................................................................................... 5

1.1 SCOPE ................................................................................................................................................ 5

1.2 APPLICABLE DOCUMENTS.................................................................................................................. 5

1.3 PRODUCT SUPPORT SERVICES ............................................................................................................ 5

1.4 DEFINITIONS ...................................................................................................................................... 6

2.0 PRODUCT DESCRIPTION........................................................................................................... 7

2.1 SYSTEM OVERVIEW ........................................................................................................................... 7

2.2 ANTENNA........................................................................................................................................... 7

2.3 RECEIVER........................................................................................................................................... 8

2.4 USER INTERFACE................................................................................................................................ 9

2.4.1 Control Head ............................................................................................................................ 9

2.4.2 Cabin Entertainment Management System (CEMS) Options ................................................... 9

2.4.3 Discrete Control Inputs ............................................................................................................ 9

2.5 SYSTEM ELECTRICAL SPECIFICATIONS............................................................................................. 10

2.5.1 Power and Load Analysis Information ................................................................................... 10

2.5.2 Audio Output Information....................................................................................................... 10

2.5.3 Satellite RF Input/Output Information.................................................................................... 10

3.0 INSTALLATION .......................................................................................................................... 11

3.1 OVERVIEW ....................................................................................................................................... 11

3.2 DETERMINING THE SYSTEM OPTIONS............................................................................................... 11

3.2.1 Quantity of Audio Sources ...................................................................................................... 11

3.2.2 User Interface ......................................................................................................................... 11

3.2.3 System Examples..................................................................................................................... 12

3.3 SYSTEM LIMITATIONS ...................................................................................................................... 14

3.3.1 Environmental Limits.............................................................................................................. 14

3.3.2 Functional Limits.................................................................................................................... 14

3.4 ANTENNA INSTALLATION CONSIDERATIONS.................................................................................... 15

3.4.1 Antenna Coaxial Cable Installation ....................................................................................... 15

3.4.2 Interference from VHF and SATCOM Transmitters............................................................... 16

3.5 AUDIO DISTRIBUTION ...................................................................................................................... 17

3.5.1 Audio Playback Interruption .................................................................................................. 17

3.5.2 Default Audio Playback Configuration .................................................................................. 17

3.6 SYSTEM MOUNTING ......................................................................................................................... 18

3.6.1 Antenna................................................................................................................................... 18

XM Radio

Installation Manual

XMR-3

Rev. C, 04/05/06 Page 4 of 31

H E A D S U P T E C H N O L O G I E S

3.6.2 Receiver .................................................................................................................................. 18

3.6.3 XMC Control Head................................................................................................................. 19

3.7 WIRING ............................................................................................................................................ 20

3.7.1 Wiring Notes ........................................................................................................................... 20

3.7.2 Grounding and Shielding........................................................................................................ 21

3.7.3 Aircraft Load Analysis Support .............................................................................................. 21

3.8 SERVICE ACTIVATION ...................................................................................................................... 22

4.0 SYSTEM CHECK......................................................................................................................... 23

4.1 POWER-UP CHECK............................................................................................................................ 23

4.2 SYSTEM TEST................................................................................................................................... 23

4.2.1 Power System and Initial Test ................................................................................................ 23

4.2.2 Audio Distribution .................................................................................................................. 23

4.2.3 Volume Mute and Configuration ............................................................................................ 24

4.2.4 Remote Control Test ............................................................................................................... 24

MAINTENANCE ....................................................................................................................................... 25

XM SIGNAL QUALITY CHECK .................................................................................................................. 25

5.1.1 Enable Maintenance Access ................................................................................................... 25

5.1.2 Signal Quality Monitor........................................................................................................... 26

5.2 SYSTEM COMMUNICATION CHECK................................................................................................... 26

5.3 SYSTEM SETUP INFORMATION.......................................................................................................... 27

5.3.1 System Firmware Version Identification ................................................................................ 27

5.3.2 Volume Config ........................................................................................................................ 28

5.4 SYSTEM TROUBLESHOOTING............................................................................................................ 29

5.5 REPROGRAMMING ............................................................................................................................ 30

LIMITED WARRANTY ........................................................................................................................... 31

XM Radio

Installation Manual

XMR-3

Rev. C, 04/05/06 Page 5 of 31

H E A D S U P T E C H N O L O G I E S

1.0 INTRODUCTION

1.1 Scope

To provide product description and installation reference information for the XM Radio

entertainment system, manufactured by Heads Up Technologies, Inc. of Carrollton,

Texas.

1.2 Applicable Documents

The following documents are included with the installation package and provide required

installation reference information:

HUT XMR-3A Wiring Reference Diagram with XM

Control Head

HUT XMR-3B Wiring Reference Diagram using 3rd

Party Cabin Audio System

HUT XMC-3A Remote Sensor Install Detail

HUT XMRANT-01-ICD Interface drawing, standard antenna

HUT XMR800-01-ICD Interface drawing, XMR800

HUT XMR400-01-ICD Interface drawing, XMR400

HUT XMR200-01-ICD Interface drawing, XMR200

HUT XMR100-01-ICD Interface drawing, XMR100

HUT XMC100-01-ICD Interface drawing, XMC100

HUT XMC-4 Operation Manual, XM Control Head

1.3 Product Support Services

Customer Service Dept.

Heads Up Technologies, Inc.

2033 Chenault Dr. Ste. #100

Carrollton, Texas 75006 USA

Tel: 972-980-4890 FAX: 972-980-4843

EMAIL: se[email protected]

For subscription activation go to XM Radio’s web site at xmradio.com or call 1-800-985-

9200.

XM Radio

Installation Manual

XMR-3

Rev. C, 04/05/06 Page 6 of 31

H E A D S U P T E C H N O L O G I E S

1.4 Definitions

Below is a list of definitions and acronyms for the purpose of this manual.

ICD – Interface Control Drawing

HUT – Heads Up Technologies, Inc.

CEMS – Cabin Entertainment Management System

XM – XM Satellite Radio, Inc.

XMWX – XM Weather

PA – Passenger Address

SDAR – Satellite Digital Audio Receiver

XMR – HUT XM Radio Receiver

Channel – 1) “receiver channel” - A single XMR module with an integrated XM

radio tuner, stereo audio output, discrete control inputs, and XM programming

selection. 2) “XM channel” - A station on the XM broadcast, such as “XM 40 -

Deep Tracks”.

Category – Group of XM channels of a specific genre.

XMR100 – 1-channel XMR

XMR200 – 2-channel XMR

XMR400 – 4-channel XMR

XMR800 – 8-channel XMR

XMC – HUT XM Radio Controller

XMRANT – Standard HUT Antenna for use with HUT XMR devices.

EMI – Electro-magnetic Interference

RFI – Radio Frequency Interference

LRU – Line Replaceable Unit

XM Radio

Installation Manual

XMR-3

Rev. C, 04/05/06 Page 7 of 31

H E A D S U P T E C H N O L O G I E S

2.0 PRODUCT DESCRIPTION

The XMR System is a Satellite Digital Audio Receiver (SDAR) entertainment device

intended for use in aircraft passenger cabins. The system receives user selectable

satellite transmitted digital audio programming providing music, news, live sports and

talk shows.

2.1 System Overview

The XMR system consists of multiple component types. Depending on the configuration

of the system, the component types can vary, however all system configurations will

have the minimum components of at least: 1) an antenna, 2) one or more receivers, and

3) a user interface.

The system design is network based to provide single point control of the entire system.

Figure 1 below, illustrates a simple block diagram of the system communications.

Figure 1 – XMR System Networking and Satellite Diagram

2.2 Antenna

The antenna receives the transmission from one or both geo-synchronous orbiting

satellites, which are pointed at the contiguous 48 states of the USA. The antenna is

similar to GPS type antennas, in that it is receive only, low profile in size with a

hemispherical receive pattern, and includes a low noise amplifier (LNA) to boost the

signal through several feet of cable to the receiver. Refer to Section 3.4 for antenna and

cable installation information.

XM Radio

Installation Manual

XMR-3

Rev. C, 04/05/06 Page 8 of 31

H E A D S U P T E C H N O L O G I E S

2.3 Receiver

This component is manufactured in 4 types, having 1, 2, 4 or 8 individual SDAR modules

or “receiver channels”. It is a multiple micro-processor based electronic device which

decodes the digital satellite signal and provides an analog stereo audio output(s) to the

listener(s).

The receiver, depending on the number of tuner modules, distributes the single antenna

input feed with an internal RF splitter to each module. On the XMR400, XMR800 and

Heads Up XM WX data receivers, an internal RF splitter incorporates an output to “daisy

chain” additional Heads Up receiver components. Please refer to the Section 3.0 for

more information.

The receiver is intended as a remote mounted device and requires a user interface to

control the functions such as channel selection, volume settings, etc. Figure 2 below

provides an illustration of the 4-channel receiver (XMR400).

Figure 2 - XMR Interface Layout (XMR400 shown)

XM Radio

Installation Manual

XMR-3

Rev. C, 04/05/06 Page 9 of 31

H E A D S U P T E C H N O L O G I E S

2.4 User Interface

The user interface can consist of different types depending on the users requirements.

Three main interface types are supported by the receiver(s): 1) the HUT XMC Control

Head, 2) data interface to a Cabin Entertainment Management System (CEMS) and 3) a

custom built device that utilizes the receivers discrete control inputs.

2.4.1 Control Head

The Heads Up XMC series control head is a microprocessor based device which

incorporates a touch-screen Liquid Crystal Display (LCD) with full color graphics. The

XMC and receiver(s) communicate through a multi-node data bus (RS-485) to transmit

and receive commands, XM channel information and other status data.

User control of the XM system receivers is provided by this device through the use the

touch-screen display. In addition, the XMC also includes an optical LED remote control

sensor (interface to an external sensor is also provided) for use with the HUT XMR100-

Remote Control Devices.

2.4.2 Cabin Entertainment Management System (CEMS) 1 Options

The receiver incorporates several communication interconnects to interface with a

CEMS to send channel change commands and receive channel information. Standard

HUT CEMS command protocol interfaces have been developed for general use. 3rd

party proprietary protocols are also implemented for interface to those parties CEMS

equipment only.

For more information on interfacing a CEMS to a XMR system, contact Heads Up

Technologies customer support via email at info@heads-up.com.

2.4.3 Discrete Control Inputs

Two types of discrete control inputs are available:

Main Interface Inputs

The J1 interface of the XMR includes a PA-key input to mute the system and

configuration-strap type inputs that allows the installer to configure the operation of the

XMR at power-up. Refer to Section 3.5.2 for more information.

Receiver Channel Interface Inputs

Discrete inputs (active ground) are included on each receiver channel for user XM

programming control to scroll (Up or Down) through each channel, category and channel

preset. These inputs are intended to be used in conjunction with a XMC since these

inputs only provide limited functionality. Please note, presets can not be set with these

inputs.

These inputs would typically be connected to an installer fabricated switch panel

mounted near a passenger seating area. An example is illustrated in Figure 3 below.

1Data protocol definition required, contact product support services.

XM Radio

Installation Manual

XMR-3

Rev. C, 04/05/06 Page 10 of 31

H E A D S U P T E C H N O L O G I E S

Figure 3 - In-Seat Control Panel Example

2.5 System Electrical Specifications

2.5.1 Power and Load Analysis Information

Power Input, Voltage 28VDC(per DO-1060D, Cat. Z)

Power Input, Current, XMR800 2.0A(nominal)

Power Input, Current, XMR400 1.0A(nominal)

Power Input, Current, XMR200 0.6A(nominal)

Power Input, Current, XMR100 0.4A(nominal)

Power Input, Current, XMC100 0.4A(nominal)

2.5.2 Audio Output Information

Output Impedance 600Ω

Output Level (Nominal) 0dBV (0.775VRMS)

Volume Adjustment Range -30 - +12dBV

2.5.3 Satellite RF Input/Output Information

Input/Output Center Freq. 2.339 GHz

Input Impedance 50-ohms

Input Expected Antenna Gain 22dB (+/- 2dB)

Output Impedance 50-ohms

Output Gain 0dB (+/- 1dB) Nominal

Connector Type SMA

Ce manuel convient aux modèles suivants

Table des matières

Manuels Récepteur populaires d'autres marques

Garmin

Garmin GA 23 Manuel utilisateur

Aiphone

Aiphone PS-12F Manuel utilisateur

IMES

IMES TCS-01CA-PMI Manuel utilisateur

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuel

AMIMON

AMIMON AMN12310 WHDI Manuel utilisateur

Dual

Dual DMCPA79BT Mode d'emploi

Sound Associates

Sound Associates SA652P Manuel utilisateur

Sherwood

Sherwood NewCastle R-772 Manuel utilisateur

Audio

Audio A10-RX Series Manuel utilisateur

AllSee

AllSee PushShare PSRV1.1 Manuel utilisateur

DEMAG

DEMAG DRC-DR D2 Manuel utilisateur

Teleco

Teleco TVRCL868A02 Manuel utilisateur

Bosch

Bosch RF3222E Manuel utilisateur

Kramer

Kramer 631R Manuel utilisateur

Xpress

Xpress xmc10 Manuel utilisateur

JVC

JVC KD-MR1BTS Manuel utilisateur

Omega Engineering

Omega Engineering UWTC-REC3 Manuel utilisateur

e-survey

e-survey E300 Pro Manuel utilisateur