HC Telecom DS815 Manuel utilisateur

1/ 16

Contents

Features

Getting Started

Step 1: Checking the packing contents

Step 2: Setting up the Base Unit

Step 3: Preparing the battery pack

Registration

Options

Adjusting the ringer and earpiece volume

Basics

MakingaCall

Calltransfer

Receiving a Call

Redialing a Call

Travelingout-of-range

Key lock/unlock

Telephone Features

Memory dialing

Storing phone numbers and names

Making calls with memory dialing

Chain dialing

Editing a stored name and/or phone number

Erasing a stored name and phone number

Paging

Handset to Handset communication

Caller ID Features

Caller ID

When the telephone rings

Viewing the Caller ID Message list

Name tagging

Deleting information from the Caller ID list

Using the Caller ID list

Additional Information

Beltclipinstallation

Headset installation

Note on power sources

Maintenance

2/ 16

Features

. 900MHz Digital Spread Spectrum Technology

. Multi-Handset operation

. Call ID Function

. 60 Number Caller ID Memories

. Lighted Keypad

. 3-Line, 16 Character Backlit Handset Display

. 29 Enhanced Memory Dial Locations

. 32 Digit Redial

. 3 Redial Memories

. Flash

. Pause

. 10 Days Standby Battery Life

. 4.5 Hours Talk Time

. Handset Earpiece and Ringer Volume Control

. Hearing Aid Compatible

3/ 16

Checking the Package Contents

Make sure you have received the following items in the package.

lBase unit

lHandset

lRechargeable battery

lAC/DC adapter

lBeltclip

lTelephone line cord and plug

lOwner’smanual

Setting up the Base Unit

Do the following steps.

lChoose the best location

lConnect thebaseunit

Choose the best location

lAfter installing the battery pack in the handset, charge your handset at least12 hours before using the

phone. Once the handset battery pack is fully charged, connect the telephone line cord to the base and

telephone walloutlet.

lThe location should be close to both a phone jack and a continuous power outlet, which is not switchable.

lKeep the base and handset away from sources of electrical noise such as motors and fluorescent

lighting.

lBe sure there is sufficient space to raise the base antenna to a vertical position.

Connect the base unit

1. Connect the telephone line cord to theTEL LINE jack and to a telephone outlet.

2. Connect the AC adapter to the DC IN 9V jack and to a standard 240V AC wall outlet.

3. Set the base unit on a desk or tabletop and place the handset on the base unit as shown. Then raise the

antenna to a vertical position.

Note Use only the supplied ??? AC adapter. Do not use any other AC adapter.

Note Connect the AC adapter to a continuous power supply.

Note Place the base unit close to the AC outlet so that you can unplug the AC adapter easily.

Preparing the Battery Pack

Charge the battery pack for at least 12 hours before you start using your phone.

1. Press in the battery cover release and slide the cover down until it comes off.

2. Connect the battery pack connector with the correct polarity (black and red wires), then correct polarity

(black and red wires), then insert the battery pack into the battery compartment.

4/ 16

3. Securely close the battery compartment cover by sliding it up until it snaps into place.

4. Place the handset on the base as shown.

5. Make sure that the status LED lights. If the LED doesn’t light, check to see that the AC adapter is

plugged in and that the handset makes good contact with the base charging contacts.

Note Use only the Uniden Battery (???) supplied with your phone. Replacement batteries are also available

through the Uniden Parts Department.

Battery use time (per charge)

From fully charged

lFour and half hours continuous use.

lTen days when the handset is in the standby mode.

When the battery charge becomes low

When the battery pack is very low and needs to be charged, the phone is programmed to eliminate functions

in other to save power. If the phone is not in use,“Low Battery”flashes and none of the keys will operate. If

the phone is in use,“Low Battery”flashes and the handset beeps. Complete your conversation as quickly as

possible and return the handset to the base unit for charging.

Note The built-in memory backup can hold numbers and names stored in the memory even if the battery

pack is completely discharged.

Cleaning the battery contacts

To maintain a good charge, it is important to clean the battery contacts on the handset and base unit with a

dry cloth or a pencil eraser about once a month.

Do net use any liquids or solvents.

Registration

The digital security code is an identification code used to connect the handset and the base unit.

In the rare situation that you suspect another cordless telephone is using the same security code, you can

change the code.

1. Remove the handset from the base unit.

2. Press and [flash] + handset No.(1~7).

3. Place the handset on the base unit.

When registration is completed, confirm tone will sound.

Handset #

Low Battery

5/ 16

Note If user want to change the ID as handset No. is 1, then other handsets

have to register again.

Options

1. Press [options]. The following screen appears.

2. When you wish to enter dial prefix, Then press [select] key and enter Dial

Prefix(1 digit) by using the numeric key(0~9).

4. After entering the Dial prefix, press [select] key.

5. After you have made your selections, press [options] and return the handset to the base.

Dial prefix : If caller’s phone is connected to PSTN via a Private Branch Exchange(PBX), Caller have to dial

one digit(Dial Prefix) to connect to PSTN. When the phone is connected to PSTN the phone sound the DIAL

TONE and caller can dialing.

Adjusting the Ringer and Earpiece Volume

Ringer tone and volume

The phone has four ringer tone and volume combinations.

In the standby mode, press []or []on the handset repeatedly.

The display shows the setting.

Earpiece volume

Pressing []or []during a call will change the earpiece volume of the handset. This setting will remain in

effect after the telephone call has ended.

When you press []in Loud mode or press []in Low mode, the error tone sounds.

Making a Call

Dialing from standby

1. Enter the phone number. (Up to 32 digits.)

Example: Enter 95979035

2. Press [talk].

“Talk”and Volume level and Handset No.appears on the display.

Example: Volume level Mid, handset No. 1

3. To hang up, press [talk] or place thehandset on the base.

Other Operations

To Do this

To adjust the earpiece volume Press []or []during a call.

To enter a pause within the dialing sequence Press [redial/p]. “P”appears in the display

which represents a pause.

Talk Mid 1

95979035

Handset #

Reg others next

Dial prefix:

95979035

6/ 16

Dialing from talk mode

1. Press [talk].

“Talk”and Volume level and Handset No.appears on the display.

Example: Volume level Mid and Handset No. 1

2. Dial the phone number.

Example: Enter 95979035

3. To hang up, press [talk] or place the handset on the base.

Call transfer

When the phone is talk mode, you can transfer the call to another handset.

1. Press [delete/page] + handset No. + [talk] key continuously.

2. Calledhandsetrings.

3. Press [talk] key on called handset then call transfer is completed.

(Auto talk and Any key answer are available)

Note If called handset is not answer during 20 seconds, the call will back to original handset.

Receiving a Call

From the handset

1. The phone rings. “Incoming call”appears on the display.

2. Press [talk].

“Talk”and Volume level and Handset No.appears on the display.

3. Talk with the caller.

4. To hang up, press[talk] or place the handset on the base.

AutoTalk when ringing

When the phone is ringing and the handset is on the base unit, simply lift the handset from the base unit to

answer the phone.

AutoTalk: Allows you to answer the phone without pressing [talk]. If the phone rings, simply remove the

handset from the base and the phone automatically answers the call. Or, if the handset is not on the base,

press any key to answer the call.

Any key answer when ringing

When the phone is ringing and the handset is off the base, press numeric keys(0~9) or [*],[#] key or [talk] key

of handset to answer the incoming call.

Redialing a Call

The last three phone numbers dialed can be quickly redialed.

Talk Mid 1

95979035_

Incoming Call

Talk Mid 1

Transfer to

Hand 

7/ 16

Redial from standby

1. Press [redial/p].

The phone number that waslast dialed appears on the display.

2. Press [redial/p] will display one of the last three numbers dialed.

Most recent

[redial/p]

Standby mode

3. Press [talk]. The number will be dialed.

Redial from talk mode

1. Press [talk].

“Talk”and Volume level and Handset No.appears on the display.

2. Press [redial/p].

The last number dialed will be displayed and redialed.

3. To hang up, press [talk] or place the handset on the base.

Note Only the last number dialed can be accessed after talk has been pressed.

Traveling Out-of-Range

During a call, as you begin to move your handset too far from your base unit, noise increases. If you pass the

range limits of the base unit, your call will terminate within 30 seconds.

Key lock/unlock

When the handset is in the ST/BY mode, press and hold [flash] key,

then sound confirm beep and display "Key Locked".

During Key Locked condition, all keys do not operate until incoming

call or press and hold [flash] keyagain and display “Key Unlocked”.

95979035_

96348578_

0293953360_

Talk Mid 1

95979035_

Key Locked

Key Unlocked

8/ 16

Storing Phone Numbers and Names

Memory Dialing allows you to dial a number using just a few key strokes. You can store up to 29 phone

numbers in the memory.

1. Press and hold [memory] until“Memory Store”is displayed.

2. Press []/ []or enter a two-digit number (01-29) to select the memory

location where you would like to store the number.

3. Press [select].

The following screen appears and a cursor flashes indicating that the display is

ready for the name to be entered. If this screen appears, the selected memory

location is already stored, Then you must either change the entry in this location,

clear the location, or select “Go Back”to choose another location.

4. Use numeric key and [*],[#] key, or [delete/page] to enter the name.

The name cannot exceed 13 characters.

lUse [#] and [*] to move the cursor to the desired location.

lUse [delete/page] to delete characters as needed.

5. Press [select]

“Store Number”is displayed. The cursor flashes indicating that the display is

ready for the number to be entered.

6. Use the number keypad to enter the phone number. The phone number

cannot exceed 24 digits.

lUse [redial/p] to enter a pause in the display shows a “P”. Each pause

counts as one digit and represents one and half second delay in time between digits.

Note The pause feature is useful for long distance calling, credit card dialing, or sequences that require a

pause between digits.

lUse [delete/page] to delete digits as needed.

7. Press [select].

The handset beeps and displays the confirmation screen.

Memory storage is complete.

For example, if you store a name and number into memory location

number 07, the display shows “Memory07 Stored”

After about 2 seconds,“Memory Store”is displayed.

8. Press [memory] to return to standby mode.

Making Calls with Memory Dialing

Memory dialing from standby

1. Press [memory].

The handset displays your programmed memory locations.

2. Press []and []or enter a two-digit number (01-29) to select the memory

location you would like to dial.

Memory Store

01>

Store Name



>Edit Memory01

Delete Memory01

Go Back

Store Number



Store Number

95979035

Memory01 Stored

01 ALEX SONG

02 MURRY WILD

03>MOM AND DAD

Memory Store

01>ALEX SONG

02 MURRY WILD

9/ 16

3. Press [talk].“Talk”and Volume level and Handset No.appears on the display.

Then the displayed number is dialed.

Display a Programmed Number

Use [#] and [*] to toggle between the names display and the numbers display.

Program name Program number

[#]

[*]

Note When the stored phone number has 14 or more digits,“+’is displayed

next to the 12th digit. ress [#] to see the extra digits and [*] to return.

Memory dialing from talk mode

1. Press [talk].

“Talk”and Volume level and Handset No.appears on the display.

2. Press [memory].

3. Enter a two-digit number (01-29) to select the memory location of the desired

phone number. The selected phone number is displayed.

Then the number is dialed.

Chain Dialing

On certain occasions after dialing a number, you may be requested to enter an access code, such as your

account number. You can enter this number into a memory location for later use by doing the following:

1. Store the access code into one of the memory locations (01-29) following the steps STORING PHONE

NUMBERS AND NAMES

2. Dial the party or service main number.

3. When you need to enter the special number, p ress [memory] followed by the memory location (01-29)

Editing a Stored Name and/or Phone Number

1. Press and hold [memory] until“Memory Store”is displayed.

2. Press []and []or enter a two-digit number (01-29) to select the memory

location you would like to edit.

3. Press [select].

The following screen appears with the memory location number that you have

selected in the display.

4. Press []or []to select“Edit Memory”, then press [select].

The following screen appears.

01 ALEX SONG

02>MURRY WILD

03 MOM AND DAD

04 Empty

05 96348587

06>001823266344

Talk Mid 1

00182326634488_

Memory Store

01>ALEX SONG

02 MURRY WILD

>Edit Memory01

Delete Memory01

Go Back

01 95979035

02>97538642

03 0123456789

Talk Mid 1

0123456789_

10/ 16

The cursor flashes indicating that the display is ready for the name to be edited.

When a name has not been stored, the cursor appears at the beginning of the

second line.

5. Press [], [], [#], [*], or [delete/page] to edit the name.

To edit only the phone number, skip this step.

6. Press [select]. The following screen appears.

The cursor flashes indicating that the display is ready for the number to be edited.

7. Use the number keypad, [redial/p] or [delete/page] to edit the phone number.

The phone number cannot exceed 24 digits. If you don’t want to change the phone number, skip this step.

8. Press [select].

The handset beeps and displays the confirmation screen. The memory storage

is complete. For example, if you store a name and number into memory

location number 01, the display shows“Memory01 Stored”.

After about 2 seconds,“Memory Store”is displayed.

9. Press [memory] to return to standby mode.

Display a Programmed Number

Use [#] and [#] to toggle between the names display and the numbers display.

Program name Program number

[#]

[*]

lWhen the stored phone number has 14 or more digits,“+”is displayed next to the 12th digit. Press [#] to

see the extra digits and [*] to return,

[#]

[*]

Erasing a Stored Name and Phone Number

1. Press and hold [memory] until“Memory Store”is displayed.

2. Press []and []or enter a two-digit number(01~29) to select the memory

location you would like to edit.

3. Press [select].

The following screen appears with the memory location number that you have

selected in the display

4. Press []to move the pointer down to the“Delete Memory”command line.

5. Press [select]. The following confirmation screen appears.

Store Name

ALEX SONG

Store Number

95979035

Memory01 Stored

Memory Store

01>ALEX SONG

02 MURRY WILD

Memory Store

01>ALEX SONG

02 MURRY WILD

Memory Store

01 95979035

02>97538642

Memory Store

05 96348587

06>001823266344

Memory Store

05 96348587

06>+88

Memory Store

01 ALEX SONG

02>MURRY WILD

>Edit Memory02

Delete Memory02

Go Back

Edit Memory02

>Delete Memory02

Go Back

Table des matières

Autres manuels HC Telecom Téléphone

HC Telecom

HC Telecom AU27018GE2-A Manuel utilisateur

Manuels Téléphone populaires d'autres marques

GE 2-9480 Manuel utilisateur

Geemarc

Geemarc PHOTOPHONE 155 Manuel utilisateur

D-Link

D-Link DWR-720/PW Manuel utilisateur

Interquartz

Interquartz Gemini IQ333 Manuel utilisateur

SSS Siedle

SSS Siedle HT 840-0 Manuel utilisateur

Motorola

Motorola TITANIUM Manuel utilisateur

Panasonic

Panasonic ICX Manuel utilisateur

LG H870DS Manuel utilisateur

Samsung

Samsung GT-I9500 Manuel utilisateur

AT&T

AT&T Trimline 205 Manuel utilisateur

Selta

Selta zenyth 600 Manuel utilisateur

Doro

Doro AFTI 20 Manuel utilisateur

UNIQCELL

UNIQCELL A1 Manuel utilisateur

Panasonic

Panasonic KX Series Manuel utilisateur

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Manuel utilisateur

BT Decor 425 Manuel utilisateur

NEC

NEC SV8500 Manuel utilisateur

Teledex

Teledex PEARL Manuel utilisateur