Hawk HB001-3S Manuel utilisateur
The Air Mover - Model HB001-3S
Hawk Enterprises of Elkhart, Inc.
Specifications:
• 1/2 HP, 120 volt ac, 60Hz, 3 speed ball bearing
(BB) motor
• 4.5, 5.0 & 6.25 Amps., 750, 1000 & 1100 rpms
• 25 Amp, 1.25 hp rated switch
• 25 ft. (7.62 m), 16-3 SJT, black power cord
with molded-on plug
• fan wheel - 11in. (46.2 cm) od, 10.75 in
(27.3 cm) long metal, .50 in (1.27 cm) bore hub
• rated 2000, 2500, & 2950 CFM air flow
• height: 18.2 in. (46.2 cm)
• width: 14.5 in. (36.8 cm)
• length: 19.5 in. (49.7 cm)
• weight: 37 lbs. (16.7 kg)
Features:
• 3 speed ac ball bearing (BB) motor
• Metal carrying handle
• Top mounted cord wrap
• Heavy duty 3-speed switch
• Durable heavy duty black roto-molded polyethylene
housing
• Heavy duty power cord with molded-on plug
• Rubber feet for non-slip positioning
• Metal guards on inlet and outlet for maximum safety
• Stackable with locating lugs
• 3 position air stream - parallel, 45°, and 90° to floor
• Compact design with exceptional performance
• UL/CUL Approved
HAWK ENTERPRISES OF ELKHART, INC.
52744 Park Six Court
Elkhart, Indiana 46514 USA
Phone: (574) 294-1910
Toll Free: (888) 289-4295
Fax: (574) 970-0289
SAFETY INSTRUCTIONS
READ AND SAVE ALL INSTRUCTIONS.
READ BEFORE USING!
When using an electrical appliance, basic
precautions should always be followed, includ-
ing the following:
WARNING
Failure to follow these safety instructions could result
in damage to the machine, damage to property, or bodily
injury.
• Do not use machine while placed in standing water.
• To reduce the risk of fire or electric shock, do not
use this fan with any solid-state speed control
device.
• To reduce the risk of electric shock, do not expose to
water or rain.
• Use machine only as described in this manual. Do
not use in ways it was not intended.
• Turn off all switches and unplug the electrical cord
when not in use and before servicing.
• Do not allow to be used by untrained personnel.
Close attention is necessary when used near children.
• Use only on GFCI protected receptacles.
• If the machine is not working as it should, has been
dropped, damaged, or left outdoors, return it to a
service center before using.
• Avoid electrical shock; do not handle the plug or
machine wet hands. To unplug the cord, grasp the
plug. Do not pull on the cord.
• Do not use an extension cord with this fan. Do not
use on outlets with a damaged cord or plug. Connect
the machine only to a properly grounded outlet (refer
to GROUNDING INSTRUCTIONS). Avoid damaging
cord (closing doors on cord, pulling around sharp
edges or corners, hot surfaces, or running machine
over cord).
• This machine creates suction and contains a revolving
fan. Keep hair, loose clothing, fingers, and all other
parts of the body away from openings and moving
parts. Do not insert an object into any of the openings
in the machine.
• Do not use in areas where flammable and/or explosive
vapor or dust is present to avoid the possibility or fire
or explosion. Some cleaning fluids can produce such
vapors.
• Do not allow air inlet openings on either side of the
machine to be obstructed; this could cause the motor
to overheat.
• Do not allow debris near front air exhaust opening
which could be thrown by the air stream.
GROUNDING INSTRUCTIONS
BEFORE YOU PLUG IN YOUR MACHINE:
Check the rating plate to see if the voltage agrees
within 10% of the voltage available.
This machine must be grounded. If it should
malfunction or break down, grounding provides a path of
least resistance for electric current to reduce the risk of
electric shock. This machine is equipped with a cord
having a equipment grounding conductor and grounding
plug. The plug must be plugged into an appropriate GFCI
outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
DANGER
Improper connection of an equipment grounding
conductor can result in risk of electric shock. Check with a
qualified electrician or service person if you are in doubt as
to whether the outlet is properly grounded. Do not modify
the plug provided with the appliance. If it will not fit the
outlet, have a proper outlet installed by a qualified
electrician (Figure 1).
USE ONLY ON GFCI PROTECTED RECEPTACLES.
UNPACKING AND SETUP
Carefully inspect all components to insure that there is
no concealed freight damage. If such damage is
discovered, file a Damage Report immediately with the
delivering carrier.
OPERATION
Place and position machine. To direct airstream as
desired, this unit can be positioned flat on floor, at a 45
degree angle upward, or 90 degrees upward. Plug power
cord into a properly grounded outlet and turn power switch
to selected speed.
CLEAN UP AND STORAGE
For compact storage, this machine can be stacked with
another. Wind the extension cord in a circle on the blower
carrying handle. Be sure not to wind the cord tighter than
necessary.
Store the machine in a cool dry place. Avoid prolonged
exposure of machine to freezing temperatures during
storage.
Det. Part Description Qty.
No. No. per unit
1 E0052A Knob - Switch 1
2 H0046-1 Nut - 3/8 - 24 Hex. 1
3 E0052 Switch - Rotary, 4 pos., 25 a, 1.25 HP 1
4 H0086 Plug - Square, Handle, Black 2
5 L0018A Label, Switch 1
6 B0015BB Motor, 1/2 HP, 3-speed, 115 vac 1
7 S0033P Grill - Air Intake, 12 in. 2
8 H0084 Screw, 1/4 - 20 x 3/4 Rd. Hd. Phil. 4
9 H0085 Washer, 1/4 ID x 1.25 OD, Fender 4
10 H0079-1 Nut, 1/4 - 20, Flex Lock 4
11 H0087 Foot, Rubber - 3/4 in. dia. 7
12 H0002 Screw 7
13 S0031P Grill, Exhaust 1
14 E0031-2 Power Cord, 16-3 SJT x 25 ft. 1
15 H0021-2 Strain Relief - Power Cord 1
15A H0022 Conduit Nut 1/2” 1
Det. Part Description Qty.
No. No. per unit
17 S0030P Handle Bar - 13.5 x 1.0 x 1.0 Black 1
18 M0004 Spacer, 5/16 x 1.0 x 1.18, Black 2
19 B0001 Blower Wheel, 11.0 x 10.75 L 1
20 S0037P Motor Brace 1
21 H0056-4 Bolt, 1/4 - 20 x 2.0, Hex Head 2
22 L0018 Label - Air Mover 1
23 C0025 Housing, Blower, Black, Poly 1
25 H0059-1 Screw, Plastic - 10 -16 x 5/8 8
26 H0097 Nut, 10 - 24 2
27 H0088 Screw, 10 - 24 x 5.0 Rd. Hd. 2
29 C0025-1 Retainer, Wire 1
32 S0034 Plate, Switch Mounting 1
33 H0059 Screw, Sheet Metal, #8 4
34 E0053 Cap., Mtr., 7.5 ufd, 370 v. 1
16 H0084-1 1/4 - 20 x 3/4 Round Head Bolt 2
LIMITED WARRANTY
Your HAWK equipment which has been manufactured, tested and inspected in accordance with carefully specified engineering
requirements, is warrantied to be free from defects in material and workmanship. This Limited Warranty is, however, subject to the
following qualifications, conditions and limitations which are set forth to provide you and all users of the HAWK equipment with
information concerning the duration, extent, availability, and applicability of this HAWK Limited Warranty, the procedure to be taken
to obtain its performance, and other information concerning the HAWK Limited Warranty policy.
The HAWK Limited Warranty is extended to the original end user as follows:
Machines: 1 year parts replacement and 1 year service labor warranty.
Replacement parts guaranteed for 90 days from date of installation against defects in material and workmanship.
This Limited Warranty will not cover damage attributable to the following:
(1) Improper, unreasonable or negligent use of abuse of the equipment
(2) Abrasions or punctures of the equipment.
The start date of the Limited Warranty coverage shall be the purchase date of the original end user or six months from the date the
machine was shipped from the Factory, whichever comes first.
Certain parts of equipment require replacement in the ordinary use due to normal wear by reason of their characteristics. Normal
wear items such as cords, switches, bumpers, bearings, etc. are excluded from the Limited Warranty.
PARTS OF EQUIPMENT NOT COVERED BY THE LIMITED WARRANTY
EXCEPTIONS AND EXCLUSIONS FROM THE LIMITED WARRANTY
PROCEDURE TO BE TAKEN TO OBTAIN PERFORMANCE OF LIMITED WARRANTY REPAIR
REPLACEMENT
NO REFUND OF PURCHASE PRICE
LIMITED WARRANTY REGISTRATION CARD FOR YOUR EQUIPMENT AND REQUEST FOR INFORMATION
This equipment is required to be used on electric current as indicated on the data plate. Otherwise damage, defects, malfunctions or
other failure of the equipment arising from use on electric current not as indicated are excepted and excluded from this Limited
Warranty. Defects, malfunctions, failure or damage of the equipment caused by improper, unreasonable or neglect use or abuse while
in possession of the purchaser are likewise excluded from this warranty. If repair is done on your equipment by anyone other than
those designated as authorized to perform such work without first having obtained factory instructions, HAWK ENTERPRISES at its
sole option, my determine that this warranty will not apply and that reimbursement for such repair will not be made because of the
failure to comply with such factory specified instructions.
To secure repair of the equipment or any warranted parts under this Limited Warranty, the following procedure should be taken. The
inoperative equipment or warranted parts, together with satisfactory evidence of the purchase date, must be delivered, with shipping
and delivery charges prepaid, to one of the following:
(1) The dealer from whom purchased;
(2) Any HAWK distributor’s service department in the United States;
(2) Any HAWK authorized service station in the United States.
If you are unable to locate any of the foregoing, you may write or otherwise communicate with HAWK ENTERPRISES before repair
service is performed by anyone else. In such event, HAWK ENTERPRISES will provide either the location or a closely available
HAWK distributor service department, or HAWK authorized service station or other factory instructions. Upon compliance with the
above procedure, all warranted defects will be repaired, at no additional charge or costs to the customer, and the repaired product
returned to the customer, with all shipping and delivery charges pre-paid. In following the procedures set forth, PLEASE MAKE
CERTAIN to state the model, type and serial number as shown on the data plate of the equipment.
In the event of a defect, malfunction or failure of your HAWK equipment or any warranted part to conform with this warranty,
HAWK may, at its sole option and own expense, replace the equipment or any warranted part with another new, identical or
reasonably equivalent model or part in lieu or repairing the defect.
HAWK will not, as a matter of it’s Limited Warranty policy, refund the customer’s purchase price.
Your HAWK distributor from whom you purchased your equipment is responsible for the registration of your Limited Warranty with
the factory. Any information or questions you may have concerning your HAWK equipment or this Limited Warranty may likewise
be secured from the factory. This Limited Warranty will give you specific legal rights, and you may also have other rights which vary
from state to state.
HAWK ENTERPRISES OF ELKHART, INC.
(888) 289-4295
(888) BUY HAWK
Autres manuels Hawk Ventilateur
