Kabeldurchführung mit Anarbeitungsflansch
HSI150 K(2) AF/X / HSI150 1x4 K(2) AF/X
6 Art. Nr.: 5090033149 Rev.: 04/2021-10-26
Entsorgung
Sofern keine Rücknahme- oder Entsorgungsvereinbarung getroffen wurde, zer-
legte Bestandteile nach sachgerechter Demontage der Wiederverwertung zufüh-
ren:
•Metallische Materialreste nach den geltenden Umweltvorschriften verschrotten.
•Elastomere nach den geltenden Umweltvorschriften entsorgen.
•Kunststoffe nach den geltenden Umweltvorschriften entsorgen.
•Verpackungsmaterial nach den geltenden Umweltvorschriften entsorgen.
EN Safety Instructions and Information
Target Group
The installation may only be carried out by technical experts.
Qualified and trained individuals carrying out installation must have
•knowledge of general safety and accident prevention regulations as amended,
•knowledge of how to use safety equipment,
•knowledge of how to use hand tools and electric tools,
•knowledge of the relevant standards and guidelines for laying pipes/cables and
for backfilling utility trenches as amended,
•knowledge of the regulations and installation guidelines of the supply company
as amended,
•knowledge of the waterproof concrete directive and building waterproofing
standards as amended.
General information and intended use
In line with their intended use, our products have been developed solely for instal-
lation in buildings made of state-of-the-art materials. Insofar as no express written
confirmation has been provided by us, we do not accept any liability for any other
purposes or purposes going beyond the above.
For warranty conditions, please see our current General Terms and Delivery Condi-
tions. We explicitly draw your attention to the fact that no warranty whatsoever
applies for any subsequent damage occurring as a result of failure to follow the
installation instructions or if our products are used incorrectly or combined with
third-party products.
Cable entries with integrated sealing flangeHSI150 K(2) AF/X
/ HSI150 1x4
K(2) AF/Xare tested by FHRK according to current test guidelines and bear the
seal "FHRK Quality".
The cable entries with integrated sealing flange HSI150 K(2) AF/X / HSI150 1x4
K(2) AF/X with integrated sealing flange are used for cable entries or for the con-
nection of cable ducts in buildings with waterproof membranes or approved poly-
mer-modified bitumen coatings (PMBC).
Safety
This section provides an overview of all the main safety aspects for optimum pro-
tection of personnel and a safe installation process.
A failure to observe the instructions and safety information set out here may re-
sult in significant hazards.
During installation of the Cable entry with integrated sealing flange it is impera-
tive to observe the relevant professional association rules, the VDE provisions, the
relevant national safety and accident prevention regulations and your company’s
guidelines (work and procedure instructions).
The fitter must wear the relevant protective clothing.
Only intact components may be installed.
The following instructions are to be observed prior to installa-
tion of the Cable entry with integrated sealing flange HSI150
K(2) AF/X / HSI150 1x4 K(2) AF/X:
Risk of injury in the event of improper installation!
Improper installation can result in significant bodily harm and
property dam-
•Observe the nationally applicable laying and filling regulations for pipes and ca-
bles.
•Seal the underground and cable substructure well prior to laying pipes or cables
so that the latter cannot subside.
No sealing due to incorrect installation!
Improper installation can result in damage.
•The incorrect laying of cables or ducts and improper filling of the cable trench
causes settlement, which can lead to damage and leaks.
•The current building waterproofing standard DIN 18533 for underground struc-
tural components is to be observed.
•The application of the component in conjunction with pre-applied fully-bonded
membrane (FBM) is not covered by DIN 18533. Suitable installation always de-
pends on the sealing sheet system manufacturer and local circumstances, and
only possible after consultation.
•Only open cable entries just before fitting with cables to avoid accidental dam-
age during foundation works.
•Do not knock the blind cover in with a hammer or sharp object!
•The Cable entry with integrated sealing flange should not be supposed to me-
chanical load through cables or pipes.
•Any cable entries with integrated sealing flange that are not required may be
used as pressure-tight back-up entries if there is an undamaged Hauff quality
seal on the closing cover.
•Do not knock the blind cover in with a hammer or sharp object!
•Open cable entries with integrated sealing flange, which are used as back-up
entries or closing cover which have been opened accidentally, should be fitted
with new HSI 150 DT/DTS respectively HSI90 D blind covers.
•Do not reuse uninstalled or damaged closing covers.
•When tapping in the safety cover (second sealing cover), the bayonet mounting
and the seal seat for the O-ring of the seal packing must not be damaged.
•Do not use cleaning agents containing solvents to clean the Cable entry with
integrated sealing flange. We recommend using the cable cleaner KRMTX.
•For details of other accessories and further information, see www.hauff-tech-
nik.de and the technical data sheets as well as the safety data sheet.
Personnel requirements
Qualifications
Risk of injury in case of inadequate qualification!
Improper handling can result in significant bodily harm and property dam-
age.
•Installation may only be carried out by qualified and trained individuals who
have read and understood these instructions.
Skilled experts
Based on their specialist training, skills, experience and familiarity with the rele-
vant provisions, standards and regulations, skilled experts are able to carry out the
work assigned, independently identifying and avoiding potential hazards.
Transport, packaging, scope of delivery and storage
Safety instructions in connection with transport
Damage in the event of improper transport!
Significant damage can occur in the event of improper transport.
•When unloading packaging items on delivery and in the course of in-house
transport, proceed with care and observe the symbols on the packaging.
Transport inspection
Inspect the delivery immediately on receipt for completeness and transport dam-
age. In the event of transport damage being visible from the outside, proceed as
follows:
•Do not accept the delivery or only do so subject to reservations.
•Make a note of the extent of damage in the transport documentation or deliv-
ery note provided by the transporter.
•Submit a claim for every defect as soon as it has been identified.
•
Claims for damages can only be asserted within the applicable claim
Scope of delivery
The scope of delivery of the single wall insert HSI150 K AF/X includes:
•Pre-assembled wall insert HSI150 K AF/X with integrated sealing flange
The scope of delivery of the double wall insert HSI150 K2 AF/X includes:
•Pre-assembled wall insert HSI150 K2 AF/X with integrated sealing flange
The scope of delivery of the wall insert package HSI150- 1x4- K(2)-AF/X includes:
•4 pre-assembled wall inserts HSI150 K(2) AF/X with integrated sealing flange
1x4
Storage
E!
Damage due to improper storage!
Significant damage can occur in the event of improper storage.
•The n.v. is to be protected from damage, damp and soiling prior to installation.
Only intact components may be installed.
•The Cable entry with integrated sealing flange must be stored in such a way
that it is not exposed to low temperatures (< 5 °C), high temperatures (> 30
°C) or direct sunlight.
Disposal
If no return or disposal agreement has been concluded, recycle dismantled com-
ponents after they have been properly dismantled:
