Harol US701 Manuel utilisateur

Assembly instructions

Pivot arm awnings

US701 - US702 - US715

art.nr. 41183

- 2 -V1-02-06

Assembly instructions pivot arm awnings US701 - US702 - US715

Contents

A. Introduction page 2

B. General warnings ! page 2

C. List of tools required page 3

D. Fitting instructions page 4

E. Electrical connections + motor page 11

F. Trouble-shooting page 15

G. Labels page 16

A. Introduction

The Harol - pivot arm awnings US701/US702 are cassette awnings. This means that, in a closed posi-

tion, fabric and roller tube are protected against weather conditions by the top board and the cover

cap. The closed case is a closed, all-protecting cassette.

The type US715 is a pivot arm awning without topboard and is therefore preferably mounted under a

balcony or other overhanging structure.

Pivot arm awnings have at least 2 projection arms. These arms are fitted in or before the opening

regardless of the fitting type of the box.

These assembly instructions explain the fitting of these systems step by step.

With this manual we confine ourselves to the instructions regarding the perfect installation of our sun

proctection. The contractor assumes full responsibility for the installation of the complete sun protec-

tion and all possible components added by this very contractor. Contractor is also held accountable for

the correct CE-labelling of the sun protection installed under his responsibility. This manual is meant

to be used by professionals only. It is not to be used by DIY-enthusiasts or apprentice fitters.

B. General warnings !

For a safe fitting, use and maintenance of this sun protection a number of precautions have to be

taken. For the safety of everyone concerned, please do take notice of the following general warnings !

- This manual is meant to be used by professionals only! It is not to be used bij DIY-enthusiasts or

apprentice fitters.

- Before you start ,please do read these instructions thoroughly.

- Be very careful and make sure of a solid footing whilst operating.

- Provide sufficent light in the fitting area. Dispose of obstacles and dirt. Make sure that, except for

the fitters, no other people are in the fitting area. Unauthorized people might be in the way or at risk

themselves.

- Whilst operating the system, you must be able to overlook the complete area and the whole of the

sun protection. There are a number of places where people might get injured. Especially watch the

following parts where people might risk getting jammed : the folding arms, the extension pole and

the casing.

- Electrical connections have to be made in accordance with the existing local norms and requirements.

The awning has been designed as a sun protection and for that reason it may not be

used as an all-weather protection. In case of heavy rain or wind the awning has to be

closed immediately. Therefore we recommend to use the sun protection in combina-

tion wth an automated wind/sun – control.

- 3 -V1-02-06

Assembly instructions pivot arm awnings US701 - US702 - US715

Guarantee and conditions :

- Harol has endeavered to design and assemble this sun protection in accordance with the ruling and

valid CE-norms. Nevertheless, feel free at any time to countercheck these interpretations with your

local national institute of normation.

- From this manual no rights can be derived. Technical alterations are possible without prior notifica-

tion.

- When dealing with larger projects, we do advise you to implement a full installation of 1 sun protec-

tion before starting with the installation of the rest of the sun protections. This way, an oversight or a

small mistake can be detected in its earliest and least expansive stadium.

- For our general conditions of sale: see pricelist.

Harol NV

Industriepark 3 - 3290 Diest

Belgium

Tel. +32 (0)13 38 01 11

Fax. +32 (0)13 31 48 03

E-mail: [email protected]

Internet: www.harol.com

C. List of tools required

- ladder(s)

- roller meter

- electric drill

- cross-head and flat-head screwdrivers

- set of open-ended or ring spanners

- ruler and pencil

- set of masonry drills Ø8mm – 12mm

- set of metal drills Ø 8mm – 10mm – 16mm

- level, waterhose, plumb line

- cord

- voltmeter or testing lamp 220 V

- test cable and switch

- 4 -V1-02-06

Assembly instructions pivot arm awnings US701 - US702 - US715

D. Assembly instructions US700

D.1. Open the cardboard wrapping

Control the width of the casing and measure the width of the opening and see whether they fully cor-

respond in the context of the fitting situation on hand.

Control the height of the system including the arms and measure the height of the opening. Look

whether they match in the context of the fitting situation.

D.2. Drilling the passage holes for the various operations

Measure the distance of the operational passage at the back of the casing and mark this distance on

the fitting surface.

Drill the hole of the operational passage through the window profile or through the wall:

For motor operation use a drill Ø10mm

For crank handle mono inside operation use a drill Ø16mm

For exterior worm gear operation with eye no hole needs to be drilled.

D.3. Control and division of the accessories

Take the bag with the accessories and divide the screws, plugs and washers equally among the number

of parts delivered. Apply the same rule to side consoles and/or wall brackets.

D.4. Fitting of the casing

Make sure the extension pole is pulled up against the casing. The casing is completely closed.

According to the local fitting situation, the box can be fitted in the following different ways:

1. Fitting of the box with side consoles (US701)

2. Fitting of the box with wall brackets (US702)

3. Fitting of the roller tube with wall consoles (US715)

Take care not to drill into the glass!

US701 US702 US715

- 5 -V1-02-06

Assembly instructions pivot arm awnings US701 - US702 - US715

Situation 1 – US701

Measure the holes to be drilled and do this on the side consoles of the box.

Transfer these marks to the wall or the fitting surface. Make sure these holes

are perfectly in line and use for this purpose waterhose and plumb line.

Do mark, if necessary, the holes for a possible wall bracket to be fitted into

the middle of the box and meant to prevent sagging of the box in the case

of great widths. Beware: the holes of this wall bracket are to be drilled higher

than those of the side consoles! Drill the attachment holes into the wall , use a

masonry drill Ø12mm. Introduce the S12 wall plugs into the holes.

Lift up the box and position the side consoles of the box in front of the holes. Then fix the side consoles

provisionally by means of the washers and the wood screws.

In the case of motor operation the motor cable has to be passed through the passage opening before

doing this.

Use a spirit level to make sure the box position is horizontal. Pull a cord from the two outer consoles in

order to control whether the box is hanging straight. Then tighten the screws firmly.

In case a wall bracket is to be used to support the middle of the box, then screw the wall bracket to the

bottom of the box, using the extra screw included (see fig.)

Make sure the holes are dust-free before pushing in the

plugs

- 6 -V1-02-06

Assembly instructions pivot arm awnings US701 - US702 - US715

Situation 2 – US702

Mark the holes to be drilled on the wall or the fitting surface by using one of the wall

brackets.The outer wall brackets have to be positioned as close as possible to the side

consoles of the box.

Make sure these holes are perfectly in line and use for this purpose waterhose and

plumb line. Do mark, if necessary, the holes for a possible wall bracket to be fitted

into the middle of the box and meant to prevent sagging of the box in the case of

great widths.

Drill the attachment holes into the wall , use a masonry drill Ø12mm.

Introduce the S12 wall plugs into the holes.

Now the wall brackets can be screwed to the wall. If necessary, adjust them to compensate for any

unevenness in the wall. Pull a cord from the two outer consoles in order to control whether the box is

hanging straight. Now tighten the screws firmly.Then lift up the box and attach it to the hooks of the

wall brackets.

In the case of motor operation the motor cable has to be passed through the passage opening before

doing this. Attach the bottom side of the box to the wall brackets, use the screws included (see fig.)

Ensure that the box is perfectly level. Pull a cord from the two outer consoles in order to control

whether the box is hanging straight.

Make sure the holes are dust-free before pushing in the

plugs

- 7 -V1-02-06

Assembly instructions pivot arm awnings US701 - US702 - US715

Situation 3 – US715

Slide the wall consoles, left and right side, including the open bearings, pro-

visionally onto the fabric roller. Measure the attachment holes to be drilled

on the wall consoles(frontal or sideways). Mark these holes on the wall or the

fitting surface. Make sure these holes are in a perfect horizontal line and use

for this purpose waterhose and plumb line.

Drill the attachment holes into the wall , use a masonry drill Ø12mm. Intro-

duce the S12 wall plugs into the holes.

Now the wall consoles can be screwed onto the fitting surface, using the washers and wood screws.

Take the fabric roller (including fabric and extension pole) and slide it with the open bearings into the

wall consoles. Attach the open bearers left and right in the wall consoles (see fig.)

In the case of motor operation the motor cable has to be passed through the passage opening before

doing this. Ensure that the fabric roller is perfectly level.

Beware of the quality of the wall, the fitting surface.

If the walls are made of cellular concrete, of soft or hollow brick, the correct type of

screw must be used, e.g. coach bolts, chemical anchoring, etc.. For this, take com-

prehensive advice from your supplier of attachment materials. The company Harol

accepts no responsibility for any attachment screws that come loose.

Make sure the holes are dust-free before pushing in the

plugs

- 8 -V1-02-06

Assembly instructions pivot arm awnings US701 - US702 - US715

Position elliptic holes in rear arm with VA/SA/WGA/GA

VA L = 300 mm (2 holes)

SA + WGA : L = 765 mm (2 holes)

GA 165 : L = 1600 mm (3 holes)

GA 195 : L = 1900 mm (3 holes)

3rd hole in the middle

101

12,5

22,5

35,5

9,5

- 9 -V1-02-06

Assembly instructions pivot arm awnings US701 - US702 - US715

D.5. Fitting of the arms:

Control the number of arms delivered. There must always be a left arm and a right arm, fitted to the

extremities of the box. The other arms have to be divided proportionally; if dealing with a coupled

awning, one arm must be fitted at the coupling

For the arms of the types VA, SA,WGA and GA: fit the arm assembly brackets for the extension pole to

the extremity of each arm

Take one arm and determine the exact fitting height. But beware! The height of the arms determines

the position of the extension pole. Ensure a correct linear positioning of the arms in correlation with

the extension pole because the extension pole closes the box!

Mark the attachment holes for the arms on the wall, do this for every arm and ensure that they are

perfectly level Use water hose and plumb line to control this.

When using the VAK-arms, the articulation points have to be shifted to the rear or to the front.

TABLE POSITION OF THE ARMS “X” with rod operation with eye “X” with mono-

command

“X” with electr.

or NTK*

SA/WGA 90 95 mm 70 mm 70 mm

VA/SA/WGA 105 95 mm 48 mm 48 mm

VA/SA/WGA 125 95 mm 48 mm 48 mm

VA/SA/WGA 140 95 mm 48 mm 48 mm

GA 165 95 mm 70 mm 70 mm

GA 195 95 mm 70 mm 70 mm

VA/SA/WGA 90 95 mm 48 mm 48 mm

VA/SA/WGA 105 95 mm 48 mm 48 mm

VA/SA/WGA 125 95 mm 48 mm 48 mm

VA/SA/WGA 140 95 mm 48 mm 48 mm

GA 165 95 mm 48 mm 48 mm

GA 195 95 mm 48 mm 48 mm

VAK 90 48 mm 48 mm 48 mm

VAK 105 48 mm 48 mm 48 mm

VAK 125 48 mm 48 mm 48 mm

VAK 140 48 mm 48 mm 48 mm

VA 90 95 mm 48 mm 48 mm

US701

US702

US701

US702

* NTK = opposite side of operation side

- 10 -V1-02-06

Assembly instructions pivot arm awnings US701 - US702 - US715

Fitting the fabric roller to the rear means a shift of 30mm. Fitting the fabric roller to the front means a

shift of 20mm.

Drill the attachment holes into the wall , use a masonry drill Ø8mm. Introduce the S8 wall plugs into

the holes.

Screw the arms tight to the wall (level). Attach the arm assembly brackets (which you have put on the

arms at a former stage) to the assembly strip in the extension pole.

Now the strings holding the arms together can be cut loose. Beware, the arms are now under consider-

able tension.

Now you can start operating the awning ( when dealing with fixed arms with chains, first remov e the

security clamp in the corner bracket of each arm)

D.6. Crank handle operation with eye - outdoors operation

In this case the screen box is supplied with an elongated plastic eye. To operate this system a crank

handle rod with a hook has to be used. Beware: always operate the system standing straight in front of

the rod exit, always use regular and avoid sudden movements. Don’t overstrain the system when you

feel a mechanical resistance.

D.7. Fitting of the cardan joint – indoors operation - For crank handle operation – mono

operation

Slide the included crank handle cardan joint and its 8x8mm square rod into the previously drilled

passage to the interior. Keep sliding until the rod grips into the opening of the gear box. Determine the

necessary length of the rod and saw it off, if necessary. The correct positioning of this bar guide is very

important and lateral contact between the rod and the wall of the cardan passage must be avoided at

all times. Make sure the rod is straightly positioned, not bent or askew. Drill the holes (Ø3.2mm) and

fasten the cardan joint to the fitting surface by means of screws.

Slide the plastified foldable crank handle over the round part of the cardan joint and use the splitpen

to connect the two items. Slide the security over the splitpen. Mark the place of the magnetic clamp

on the window profile or the wall and fix it by drilling . Make sure the metal part of the deployed crank

handle touches the magnetic clamp.

Detachable rod with rod coupling: the detachable folding rod has a funnel-shaped end. A splitpen is

slid on the globular free-hanging part of the cardan joint. A turning movement can attach or detach

the crank handle.

Make sure the holes are dust-free before pushing in the plugs

Watch out not to drill too close to the edge of bricks!

Great care must be taken there. The arms are under great stress. Before having taken

the necessary precautionary measures never remove the straps that keep the arms in

a closed position.

Ce manuel convient aux modèles suivants

Autres manuels Harol Accessoires

Harol

Harol PR210 Manuel utilisateur

Harol

Harol SL400 Manuel utilisateur

Harol

Harol TC110 Manuel utilisateur

Harol

Harol CA430 Manuel utilisateur

Harol

Harol TR850 Manuel utilisateur

Harol

Harol VZ080-ZIP Guide de l'utilisateur

Harol

Harol VZ520 Manuel utilisateur

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur