Harman Kardon LSR4326P Manuel utilisateur

LSR4326P/4328P Speaker Type Setting Procedure:

The LSR4300 “speaker type” parameter is set in the speaker’s firmware to load the

correct instructions for the LSR4328P and LSR4326P speaker models. Incorrect setting

of the speaker type parameter may result in compromised performance. If the speaker

exhibits either of the following symptoms, the speaker type parameter may be incorrectly

set:

Symptoms:

1) During the speaker boot sequence just prior to normal operating display (a

single green LED is illuminated at the left end of the display), every other

LED on the front panel is illuminated.

2) When using LSR4300 Control Center Software, one or more networked

speakers are not recognized by the software.

Following is the procedure that allows a user to reset the speaker type parameter.

Procedure:

1) Unplug all of the cables from your speaker including the power cable.

2) Hold the ‘+’ button on the front panel and apply power to the unit (connect

power cord.) Keep the ‘+’ button pressed until the boot sequence is complete.

The speaker logo and the first green LED segment will illuminate when the

boot sequence is completed.

Enter the Speaker Type menu by pressing the ‘Solo’ button on the front panel

two times.

3) If the speaker model is an LSR4326P 6” speaker, press the ‘+’ or ‘-‘ button so

the SIX green segments on the left of the display are illuminated.

If the speaker model is an LSR4328P 8” speaker, press the ‘+’ or ‘-‘ button so

the EIGHT orange segments on the right of the display are illuminated. Make

sure you choose the correct setting for your speaker model. Incorrect setting

of speaker type may result in performance issues.

4) Once the proper segments are illuminated, press the ‘RMC’ button to exit that

mode.

5) To complete the process, perform the following Factory Reset procedure:

Disconnect the power cord. Set all rear-panel DIP switches to the UP or ON

position. Reconnect power cord and wait about 10 seconds for sequence to

finish. The sequence is complete when all LEDs on the front panel display

are dark and the logo is dimly illuminated.

6) Disconnect the power cord. Reset rear panel DIP switches to desired settings

and re-apply the power to restart the unit. You should no longer see every

other LED lit prior to the normal operating display.

The speaker type has been set.

END

Date: 04/01/07

Ce manuel convient aux modèles suivants

1

Table des matières

Autres manuels Harman Kardon Système de haut-parleurs

Harman Kardon

Harman Kardon SOUNDSTICKS II Manuel utilisateur

Harman Kardon

Harman Kardon HK50 Manuel utilisateur

Harman Kardon

Harman Kardon SB 16 Manuel utilisateur

Harman Kardon

Harman Kardon Kardon Onyx Studio Manuel utilisateur

Harman Kardon

Harman Kardon SoundSticks Wireless Manuel utilisateur

Harman Kardon

Harman Kardon HKTS 10 Manuel utilisateur

Harman Kardon

Harman Kardon HKTS 10 Manuel utilisateur

Harman Kardon

Harman Kardon HKTS 11 Manuel utilisateur

Harman Kardon

Harman Kardon SB 30 Manuel utilisateur

Harman Kardon

Harman Kardon CITATION 5.0 Manuel utilisateur

Harman Kardon

Harman Kardon HK40 Manuel utilisateur

Harman Kardon

Harman Kardon S300P Manuel utilisateur

Harman Kardon

Harman Kardon HKTS 200BQ Manuel utilisateur

Harman Kardon

Harman Kardon FORTY Manuel utilisateur

Harman Kardon

Harman Kardon HKTS-10 Manuel utilisateur

Harman Kardon

Harman Kardon NOVA Manuel utilisateur

Harman Kardon

Harman Kardon Aura Manuel utilisateur

Harman Kardon

Harman Kardon FIFTY Manuel utilisateur

Harman Kardon

Harman Kardon HKTS 5 Manuel utilisateur

Harman Kardon

Harman Kardon SOUNDSTICKS Manuel utilisateur

Harman Kardon

Harman Kardon OMNI 10 Manuel utilisateur

Harman Kardon

Harman Kardon HKTS 15 Manuel utilisateur

Harman Kardon

Harman Kardon Sabre SB35 Manuel utilisateur

Harman Kardon

Harman Kardon HK50 Manuel utilisateur

Manuels Système de haut-parleurs populaires d'autres marques

JVC

JVC CA-MXK5R Manuel utilisateur

LG

LG NB4532B Manuel utilisateur

JVC

JVC CA-FSH100 Manuel utilisateur

5Core

5Core Pro Series Manuel utilisateur

EAW

EAW MQV1394e Manuel utilisateur

Lynx

Lynx GXR-LA10A Manuel utilisateur

iLive

iLive ITB066B Manuel utilisateur

RDX

RDX QuickStation 4 Manuel utilisateur

Electro-Voice

Electro-Voice S-122 Manuel utilisateur

Sven

Sven SPS-619 GOLD Manuel utilisateur

Pioneer

Pioneer CS-7070 Manuel utilisateur

EAW

EAW UB82e Manuel utilisateur

Sondpex

Sondpex Active Speaker System and Digital Music... Manuel utilisateur

JVC

JVC NX-PN7 Manuel utilisateur

Marshall Amplification

Marshall Amplification AR-DM61-BT Manuel utilisateur

Yamaha

Yamaha NX-A01 - Speaker Sys Manuel utilisateur

SE Audiotechnik

SE Audiotechnik I-LINE Manuel utilisateur

Gemini

Gemini WRX-843 Series Manuel utilisateur