HappyJapan HCS2 Manuel utilisateur

SAUC01-27

HCS2

Compact Single-head Embroidery Machine

Original instructions

INSTRUCTION BOOK

Program Ver. *2.23~

-SA -3

INDEX

IMPORTANT SAFETY INSTRUCTIONS... 1-1

WARNING LABELS & THEIR LOCATIONS

..... 1-2

SETTING UP THE MACHINE

Remove the machine from box............... 2-1

Accessories............................................. 2-3

Assemble machine unit........................... 2-4

Machine installation ................................ 2-5

Grounding instruction.............................. 2-7

Disposal of a battery ............................... 2-7

MAIN PARTS............................................. 3-1

THE CONTROL BOX ................................ 3-3

DRIVE MODE............................................ 3-4

Frame change................................... 3-8a

MENU................................................... 3-A

INSERTING A NEEDLE............................. 4-1

SELECT NEEDLES AND THREADS ....... 4-2

BACKING MATERIALS ............................. 4-3

BOBBIN WINDING

Winding the bobbin ................................. 4-4

Removing the bobbin.............................. 4-5

Inserting the bobbin ................................ 4-5

Adjusting bobbin thread tension.............. 4-5

Inserting the bobbin case........................ 4-5

THREADING THE MACHINE

How to thread upper thread .................... 4-6

HOW TO READ THESE INSTRUCTIONS and SCROLLBAR

4-8

DISPLAYING THE PATTERN IN SETTING MODE

... 4-9

TURNING THE MACHINE ON

How to turn on the machine.................... 5-1

How to turn off the machine.................... 5-1c

Calendar and clock setting...................... 5-2

MESSAGE................................................. 5-3

PREPARATION OF PATTERN DATA

Connecting to a PC................................. 5-4

Reading embroidery pattern data from

the PC

.....................................................5-4b

Read embroidery pattern data ............... 5-5

Reading pattern data .............................. 5-6

Selection of folders ................................. 5-9

How to select patterns from memory ...... 5-A

Erasing patterns from memory................ 5-B

NEEDLE BAR SELECTION ......................5-E

SEWING WITH TUBULAR FRAMES

Installing and removing the frame base.. 6-1

How to hoop............................................ 6-2

Putting the hoop on the machine ............ 6-3

Starting to embroider .............................. 6-4

CAP FRAME (OPTION)

Changing the needle plate...................... 7-1

Installing and removing the cap drive frame

.. 7-2

Normal cap frame ................................... 7-5

Wide cap frame....................................... 7-8

Starting to embroider ..............................7-B

ADJUSTING THE THREAD TENSIONS... 8-1

ADJUSTING THE LASER POINTER (OPTION)

.. 8-2

SEWING

What to do if the thread breaks while sewing

9-1

Stopping and resuming sewing............... 9-1

Loss of power while embroidering .......... 9-2

Moving the hoop while embroidering and then returning to

the correct location (Position)

............................. 9-3

Moving back to the starting point (Origin) 9-3

Going back to the beginning of the design (Top)

... 9-4

Placing the design in the center of the selected

embroidery frame

(Center)

........................... 9-4

Rotating and mirroring designs (Convert)

.. 9-5

Starting in the middle of a design (Position) ...

9-6

POSITION ALIGNMENT BY DEFINING 2 POINTS

.. 9-8

POSITION .................................................9-B

Piece number.......................................... 9-C

Bobbin thread alarm..............................9-Ca

Work save .............................................9-Ce

Entry........................................................ 9-E

Return .....................................................9-F

READING

Join ....................................................... 10-1

Pattern Read Settings........................... 10-3

PATTERN

Locking pattern data ..............................11-1

Trace type ..............................................11-2

Export.....................................................11-3

Renaming patterns.................................11-5

Copying pattern data..............................11-6

Moving pattern data ...............................11-7

Renaming folders...................................11-9

Sort ........................................................11-A

Thread break report .............................. 11-B

0_1 UC01

0-1

-SA -4

INDEX

0_2 UC01

0-2

Retrieve built-in data from machine ...... 11-C

Searching pattern data.......................... 11-D

NEEDLE BAR SELECTION .................... 12-1

Auto setting................................................12-2

Thread color...............................................12-4

Color change data registration...................12-6

Color change data read .............................12-7

Repetition of color group setting................12-8

FRAME CONFIRMATION ............................13-1

Frame selection

............................................13-2

Adjusted for embroidery area ....................13-4

User-dened frames (1 ~ 5).......................13-7

User-dened frames (6 ~ 20).................... 13-A

How to change center point of frame (1 ~ 5, 6 ~ 20)

..... 13-H

Non registered .......................................... 13-J

PATTERN SETTINGS ..................................14-1

Scaling .......................................................14-2

Width adjustment .......................................14-3

Angle..........................................................14-4

Repeat sewing ...........................................14-5

Auto origin..................................................14-7

Offset .........................................................14-8

Frame out ................................................. 14-D

MACHINE SETTINGS..................................15-1

LOCK STITCHES.........................................15-5

LETTER........................................................16-1

QUEUE.........................................................17-1

Alter and Execution ...................................17-2

Needle bar selection and Pattern settings

........17-4

Registration of QUEUE setting ..................17-6

Read QUEUE setting.................................17-7

OTHER SETTINGS

Create network ..........................................18-1

Version information ....................................18-3

Language...................................................18-5

Calibrate ....................................................18-6

User maintenance mode............................18-8

Report...........................................................19-1

GUIDE ..........................................................20-1

SCREEN SAVER..........................................21-1

i-CUSTOM............................................... 22-1

LAN connection .........................................22-2b

TASK RESERVATION ............................. 22-2c

Reading................................................. 22-2d

Needle bar selection ............................. 22-2e

Setting................................................... 22-2f

Search................................................... 22-2g

List ........................................................ 22-2h

Letter..................................................... 22-2i

Layout ................................................... 22-2j

USER MANAGEMENT

Registration of administrator......................22-3

Registration of user....................................22-6

Selection of user (Login)............................22-8

Selection of user (Login) at power ON.......22-9

LAYOUT ...................................................... 22-A

THREAD SET...........................................22-J

SPECIFICATIONS • MAINTENANCE

Specications.............................................23-1

Oiling..........................................................23-1

Cleaning of rotary hook

Cleaning of thread cutting knife .................23-2

ERRORS AND WHAT TO DO ......................24-1

INITIALIZING OF MACHINE SETTINGS

Re-Initialization of machine system,

Initialize the PMS .................................. 25-1

Initializing of machine speed......................25-2

HELPFUL HINTS..........................................26-1

EMBROIDERY TERMS................................26-2

BUILT-IN FONT LIST....................................26-3

BUILT-IN PATTERNS LIST...........................26-4

VARIOUS SPECIAL FRAMES (OPTIONS)

.... 27-1

-SJ -5

IMPORTANT SAFETY INSTRUCTIONS

1_1 N401

1-1

This electrical appliance is intended for household use.

When using an electrical appliance, basic safety precautions should always be followed, includ-

ing the following.

Read all instructions before using this appliance.

DANGER - To reduce the risk of electric shock:

1. An appliance should never be left unattended when plugged in. Always unplug this appliance

from the electric outlet immediately after using and before cleaning.

WARNING

To reduce the risk of burns, fire, electric shock, or injury to persons:

1. Do not allow to be used as a toy. Close attention is necessary when this appliance is used

by or near children.

2. Use this appliance only for its intended use as described in this manual. Use only attach-

ments recommended by the manufacturer as contained in this manual.

3. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, if it

has been dropped or damaged, or dropped into water. Return the appliance to the nearest

authorized dealer or service center for examination, repair, electrical or mechanical adjust-

ment.

4. Never operate the appliance with any air openings blocked. Keep ventilation openings of the

sewing machine and foot controller free from the accumulation of lint, dust, and loose cloth.

5. Never drop or insert any object into any opening.

6. Do not use outdoors.

7. Do not operate where aerosol (spray) products are being used or where oxygen is being

administered.

8. To disconnect, turn all controls to the off (“0”) position, then remove plug from outlet.

9. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

10.Keep fingers away from all moving parts. Special care is required around the sewing ma-

chine needle.

11.Always use the proper needle plate. The wrong plate can cause the needle to break.

12.Do not use bent needles.

13.Do not pull or push fabric while stitching. It may deflect the needle causing it to break.

14.Switch the sewing machine off (“0”) when making any adjustments in the needle area, such

as threading needle, changing needle, threading bobbin, or changing presser foot, etc.

15.Always unplug sewing machine from the electrical outlet when removing covers, lubricating,

or when making any other user servicing adjustments mentioned in the instruction manual.

SAVE THESE INSTRUCTIONS

-SA -5

WARNING LABELS & THEIR LOCATIONS

1_2 M201

1-2

Trapping hazard

Shut the cover when starting the machine.

Do not put hands in while the machine is running.

Trapping, Puncture, Cut hazard wherever this

label is found

Shock hazard on all electrical components

Injury risk on moving head(s)

Keep hands away from the moving heads while the

machine is running.

Laser beam (Class 1)

Do not stare into the beam.

ES-HMF-5113-0

WARNING

Shut the cover when starting the

machine. Do not put hands in

while the machine is running.

Fear of serious injury.

ES-HMF-5117-0

CAUTION

Keep hands away from the

moving heads while the

machine is running.

Possibility of injury.

CAUTION: Injury risk on frame and carriage

Keep hands away from the drive

frame while the machine is

running.

Catch a finger in the X-carriage.

WARNING: Injury risk warning

for all needles

Keep fingers away from

the needles while

the machine is running.

Laser beam (Class 1)

CAUTION

Do not stare into the beam.

-SJ -9

SETTING UP THE MACHINE

2_1 UB12

2-1

CAUTION: To prevent accidents.

The machine is quite heavy for one person to carry.

Please use two persons when unpacking or carrying.

CAUTION: To avoid problems.

Make sure to hold bottom of the machine body when

removing from the box.

Do not hold any other place. (bed, moving head, con-

trol box etc.).

We recommend unpacking should be done where it has enough room.

Remove the machine from box

1. Remove 2 straps from the carton.

2. Lift the box (upper) to remove.

3. Take out the accessories.

Refer to the next page.

4. Take out the styrene foam (right) and (left).

5. Take out the styrene foam (lower front), (lower

right), and (lower left).

Be careful not fall down the machine, tilt the ma-

chine slightly when taking out the styrene form

(lower right) and (lower left).

6. Carry the machine to installation location.

Please keep those packing materials in case

of necessary for repair or other reasons.

Packing procedure is the reverse from un-

packing procedure.

Straps

Box (upper)

Styrene foam

Styrene

How to carry machine

The unpacked machine should be carried by 2 person with the hand position at

shown in

photos.

Right side

Left side

The person hold-

ing the machine

from right side

need to hold the

machine arm by

left hand.

Right hand

Left hand

Right side

-SA -9

SETTING UP THE MACHINE

2_1b UC01

2-2

Placement of Accessories

Conrm all the accessories are contained when unpacking.

Frame base

USB ash drive (Instruction manual,

Parts list, Happy Link Software)

Instruction manual

Embroidery frame (Round)

Embroidery frame (Square)

Thread stand

Thread guide bracket

Carriage

Thread stand felt (13 pcs)

Power line cord ass’y

Oiler

Sewing machine oil

Thread guide pillar (2 pcs)

Thread stand pin (13 pcs)

Wave washer (13 pcs)

Front cover

Tool box

Antenn (Option WLAN)

-SA -10

SETTING UP THE MACHINE

Accessories

Please conrm you have received the following.

2_2 TA02

2-3

1. Thread guide bracket

2. Thread guide pillar (2 pcs)

3. Thread stand

4. Thread stand felt (13 pcs)

5. Thread stand pin (13 pcs)

6. Wave washer (13 pcs)

7. Carriage

8. Frame base

9. Embroidery frame (square) PTA-32320-360

10. Embroidery frame (Round)

PTA-15-360

11. Needle (DB X K5) (10 pcs)

12. Oiler

13. Sewing machine oil

14.USBashdrive

(Instruction manual, Parts list. Happy Link Software)

15. Bobbin (1 pc)

16.Instructionbook(USBashdrive)

17. LAN cable

18.Powerlinecordass’y(Ashapewillbechanged

depending on a destination)

19. Fuse (6A)

20. Off set screw driver

21. #2 (+) Screw driver

22. 2 mm (-) Screw driver

23. 3 mm hexagonal driver

24. 2.5 mm hexagonal driver

25. Brush

26.Clamplter

27. Stylus

28. USB cable

Tools

1246

789

11 12 13 14 16

21 22 23 24

30. Antenn (Option WLAN)

-SA -11

Assemble machine unit

1. Insert the thread stand pin with wave washer on the

thread stand by turning clockwise, Then insert thread

stand felt.

2. Put the thread stand on to the machine and insert the

thread guide pillar.

(set nut knob nut into the thread guide pillar and 2

washers)

Turn the thread guide pillar clockwise with a 3 mm hex-

agonal driver until tight.

Turn the knob nut clockwise with a 3 mm hexagonal

driver until tight.

3. Install the thread guide bracket with supplied screws

(pan head screw M6 x 10 2 pcs).

4. Loosen the screw with a offset driver and remove the

red shipping collars that are equipped on the both side

of the guide bar. (Keep the shipping collars. It is neces-

sary when packing.)

5. Put the carriage and carriage arm together with screw

(M4 X 8 2 pcs).

2 pins in the upper carriage arm will t into holes on

the lower carriage.

6. Raise slowly the control box to the front then x it with

2 supplied screws (M4 1 pcs).

7. Connect the cable of carriage to the machine with

xed screw.

8. Install the arm for tubular embroidery. Please refer to

(page 6-1) “Installing and removing the frame base”.

Or, Install the cap frame for the cap embroidery.

Please refer to (page 7-1) “Installing and removing the

cap drive frame”.

9. Insert built-in stylus into the holder (slot) of control

box.

When taking the machine apart in case of packing,

the process is opposite of assembling the machine.

Please do exactly the opposite way of assembling.

When packing the machine up for transportation, be

sure to select the sixth needle and x it with ship-

ping collars on the both side of the guide bar.

2_3 RC01

2-4

SETTING UP THE MACHINE

Table des matières

Autres manuels HappyJapan Machine à coudre

HappyJapan

HappyJapan HCR3E Series Manuel utilisateur

HappyJapan

HappyJapan HCD2-1501-40 Manuel utilisateur

HappyJapan

HappyJapan HCH(Puls) Manuel utilisateur

HappyJapan

HappyJapan HCH-701-30 Manuel utilisateur

HappyJapan

HappyJapan HCR3E Series Manuel utilisateur

HappyJapan

HappyJapan HCH Plus Manuel utilisateur

Manuels Machine à coudre populaires d'autres marques

Riccar

Riccar RL634DE Manuel utilisateur

Singer

Singer 2517 Manuel utilisateur

Pfaff

Pfaff 3307-1 SERIES Manuel utilisateur

Janome

Janome Quilt Maker Pro 18 VERSA Manuel utilisateur

Siruba

Siruba C007JP Manuel utilisateur

Husqvarna Viking

Husqvarna Viking Designer SE Manuel utilisateur

Singer

Singer 148-5 Manuel utilisateur

IKEA

IKEA SY Manuel utilisateur

Pfaff

Pfaff 571 Manuel utilisateur

Singer

Singer 15-91 Manuel utilisateur

Brother

Brother BB370 Manuel utilisateur

Pegasus

Pegasus WT100 Series Manuel utilisateur

Reliable

Reliable 7100DB Manuel utilisateur

Pfaff

Pfaff 937 Manuel utilisateur

Singer

Singer 6038 Manuel utilisateur

Singer

Singer 413K Manuel utilisateur

Pfaff

Pfaff 1471 E1 Manuel utilisateur

Kenmore

Kenmore 16677 - Serger Sewing Machine Manuel utilisateur