Hangar 9 Cap232 Manuel utilisateur

ALMOST READY-TO-FLY

PRE-BUILT

INSTRUCTION MANUAL

WE GET PEOPLE FLYING

Specifications

Wingspan: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73′′

Length:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 1/4′′

Wing Area:. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1031 sq. in.

Weight (Approx.):. . . . . . . . . . . . . . . . . . . 11–12 lbs.

Recommended Engines:1.08 –1.20 2-Stroke

1.20 –1.50 4-Stroke

• 90% pre-built

• Highest quality Du-Bro and Sullivan hardware included

• Pre-covered in genuine UltraCote®featuring Matt Chapman’s

full scale trim scheme

• Pre-finished fiberglass cowl and wheel pants

Table of Contents

Introduction 3

Warning 3

AdditionalEquipment Required 3

Toolsand SuppliesRequired 4

Contentsof Kit 5

Section1: Hingingthe Ailerons 6

Section2: Joiningthe WingHalves 8

Section3: Installingthe AileronServos 12

Section4: Installingthe AileronLinkages 14

Section5: Mountingthe Wingto theFuselage 16

Section6: Installingthe Tail(Vertical andHorizontal Stabilizer) 19

Section7: Hingingthe HorizontalStabilizer andElevator 22

Section8: Hingingthe Rudderand Installingthe TailWheel 23

Section9: Installingthe ControlHorns 25

Section10: Installingthe MainLanding Gear 28

Section11: Assemblingand Mountingthe WheelPants 29

Section12: Installingthe Engine 31

Section13: Assemblingand Installingthe FuelTank 32

Section14: Installingthe Radio 34

Section15: Installingthe ControlLinkages 36

Section16: Attachingthe Cowling 38

Section17: Attachingthe Canopy 40

Section18: Balancingthe CAP 41

Section19: ControlThrow Recommendations 41

Pre-Flightat theField 42

AMASafety Code 43

Introduction

Congratulationson yourpurchase ofone ofthe finestARFs tobe produced!The Hangar9 CAP232 isa high-performanceaircraft best

suitedfor themore experiencedflyer andmodeler. Althoughthis isan ARF(Almost-Ready-to-Fly) kit,it doeshave someconstruction

featuresthat canbe challengingfor anew modeler.If youencounter difficultyin anyconstruction sequence,please feelfree to contact

oneof ourtechnicians—we standready toprovide anyassistance wecan concerningthe constructionof yourCAP. Youcan contact

usat 217-355-9511.

Warning

AnR/C aircraftis nota toy!If misusedit cancause seriousbodily harmand damageto property.Fly onlyin openareas, preferably

AMA(Academy ofModel Aeronautics)approved flyingsites, followingall instructionsincluded withyour radioand engine.

Additional Equipment Required

Radio Equipment

4Channels (minimum)

5Standard Servos

Standard600–1000 mAh Receiver Battery Pack

Y-Harness(if anon-computer radiois used)

Engines

1.08-1.2 2-CycleEngines

1.20-1.50 4-CycleEngines

Recommended 2-Cycle Engines Recommended 4-Cycle Engines

Webra1.20 Saito 1.20- 1.50

Saito1.20GK -1.50GK

Parts

AileronExtension (2)(JRPA114, 12′′silver) Tru–Turn Adaptor(for appropriateengine)

3′′Tru–Turn Spinner(TRU3002) Dubro KwikFueler Valve

Recommended JR Systems

JRXF642

JRXP783

JRXP8103

PCM10SxII

Propeller

FuelFilter

Foamfor CushioningTank

FuelTubing

Tools and Supplies Required

Adhesives

ThinCA (cyanoacrylate)glue

ThickCA (cyanoacrylate)glue

6-minuteepoxy

12-minuteepoxy

30-minuteepoxy

BlueLocktite 242

Canopyglue (R/C56)

Silversolder (StayBrite)

Tools

Drill

Drillbits: 1/16′′,5/32′′, 1/4′′,1/8′′

Solderingiron

SmallPhillips screwdriver

MediumPhillips screwdriver

Z-bendpliers

Pliers

1/16′′hex wrench

Smallround file

Moto-Toolwith sandingdrum

Hobbyknife with#11 blade

Mixingstick

Epoxybrush

90-degreetriangle

Sandingstick (mediumor fine)

Mediumsandpaper

Maskingtape

Straightedge

Measuringdevice (e.g.,ruler, tapemeasure)

Scissors

Papertowels

Waxpaper

Rubbingalcohol

Felttipped pen

Optional Equipment

Radiopacking foam

Antennatube

Contents of Kit

Large Parts

A.Fuselage E. Horizontalstabilizer withelevators

B.Left winghalf withaileron F. Cowl

C.Right winghalf withaileron G. Wheelpants (2)

D.Vertical stabilizerwith rudder

Other Parts

1. Pushrod& accessories 6. Fueltank andhardware

2. 1/8′′plywood die-cutparts 7. Trim sheet

3. Mainlanding gear 8. Metalmotor mounts

4. Hardwarebag 9. Canopy

5. Wheels 10. Tailwheel

Note: Thecontrol surfaces,including theailerons, elevators

andrudder, arepre-hinged withthe hingesinstalled,

butthe hingesare not gluedin place.It isimperative

thatyou properlyadhere thehinges andailerons in

placeper thesteps thatfollow usinga highquality thin

CAglue.

Step 1. Carefully remove the aileron from one of the wing

panels.Note theposition ofthe hinges.The CAPcomes with

highquality CA-typehinges.

Step 2. Remove eachhinge fromthe wingpanel andplace a

t-pinin thecenter ofeach. Slideeach hingeinto thewing panel

untilthe t-pinis snugagainst thewing.

Step 3. Slide theaileron ontothe winguntil thereis onlya

slightgap. Thehinge isnow centeredon thewing paneland

aileron.Remove thet-pin andsnug theaileron againstthe wing

panel.This willensure thatthe hingesare centered.

Step 4. Deflect the aileron and completely saturate the hinge

withthin CAglue. Theaileron’s frontsurface shouldlightly

contactthe wingduring thisprocedure. Ideally,when thehinge

isglued inplace, a1/32′′ gapor lesswill bemaintained

throughoutthe lengthof theaileron. Thehinge isconstructed of

aspecial materialthat allowsthe CAto wickor penetrateand

distributethroughout thehinge, securelybonding itto thewood

structure.

Section 1. Hinging the Ailerons

• Rightwing panelwith aileronand hinges

• Leftwing panelwith aileronand hinges • Instantthin CAglue

• CAremover/debonder

• Papertowels

• T-pin(one foreach hinge)

Parts Needed Tools and Adhesives Needed

Step 5. Turn the wing panel over and deflect the aileron in the

oppositedirection andfrom theopposite side.Apply thinCA

glueto eachaileron hinge,making surethat theCA penetrates

intoboth theaileron andthe wing.

Step 6. Using CA remover/debonder and a paper towel, remove

anyexcess CAglue thatmay haveaccumulated onthe wingor in

theaileron hingearea.

Step 7. Repeat this process with the other wing panel, securely

hingingthe aileronin place.

Step 8. After both ailerons are securely hinged, firmly grasp the

wingand aileronto checkthat thehinges aresecurely gluedand

cannotbe pulledout. Dothis byapplying mediumpressure,

tryingto separatethe aileronfrom thewing. Usecaution thatyou

donot crushthe wingstructure.

Note: Workthe aileronup anddown severaltimes to“work

in”the hingesand checkfor propermovement.

CONTINUED

Section 1. Hinging the Ailerons

Step 1. Locate the dihedral brace (also called the wing joiner).

Usingthe ruler,determine thecenter ofthe braceand markit

witha pencil.

Step 2. Trial fitthe dihedralbrace intoone ofthe wingpanels. It

shouldinsert smoothlyup tothe centerline markedin Step1.

Nowslide theother wingpanel ontothe dihedralbrace untilthe

wingpanels meet.If thefit isoverly tight,it maybe necessaryto

sandthe dihedralbrace.

Step 3. Check for the correct dihedral angle. Place the wing on

alarge, flatsurface withone wingpanel restingon theflat

surface.The oppositewing tipshould beat 3′′in heightfrom the

surface(see illustrationbelow). Ifnecessary, sandthe dihedral

braceuntil thisis achieved.There shouldbe nogaps inthe wing

center.

Step 4. To checkfor adequateclearance ofthe cowlbetween the

wing’sleading edgeand thefuselage, trialfit thewing together

andtemporarily installon thefuselage withthe cowlinstalled. If

theclearance isnot adequate,install theextra plywoodcenter

wingrib toprovide thenecessary clearance(see diagramat left).

• Right/leftwing panels

• Dihedralbrace

• Plywoodwing dowelplate

• Woodendowels

• Wingbolt plates

• Wingtrim tape(white)

• 30-minuteepoxy

• 6-minuteepoxy

• Epoxybrush

• Maskingtape

• Hobbyknife

• Rubbingalcohol

• Papertowels

• Waxpaper

• Ruler

• Pencil

• Mediumsandpaper

• Mixingstick

Parts Needed Tools and Adhesives Needed

Section 2: Joining the Wing Halves

3′′

Clearance Cowl

Wing

Fuselage

Step 5. Mix up approximately 1 ounce of 30-minute epoxy.

Note: Itis extremelyimportant touse plentyof epoxywhen

joiningthe winghalves.

Step 6. Using a scrap piece of wood or an epoxy brush, smear a

generousamount ofepoxy intothe wingdihedral bracecavity in

onewing panel.

Step 7. Coat one half of the dihedral brace with epoxy up to the

pencilline drawnin Step1. Notethe orientationof thewing

brace— the“V” pointsto thetop ofthe wing,or facesup. Install

theepoxy-coated sideof thedihedral braceinto thewing joint

cavityof thewing half,up tothe centerline, makingsure the“V”

sideof thedihedral braceis orientatedcorrectly.

photo4-6B

Step 8. Apply a generous amount of epoxy into the wing brace

cavityof theother wingpanel.

Note: Youwill needto mixup additionalepoxy tocomplete

thejoining process.

Step 9. Now apply epoxy to all sides of the exposed area of the

dihedralbrace anduniformly coatboth wingroots withepoxy.

CONTINUED

Section 2: Joining the Wing Halves

Step 10. Carefully slide the two wing halves together and firmly

pressthem together,allowing theexcess epoxyto runout. There

shouldnot beany gapin thewing halves.Use rubbingalcohol

anda papertowel toclean upany excessepoxy.

Step 11. Apply masking tape at the wing joint to hold the wing

halvestogether securely.Place thewing ona flatsurface. With

onewing panellying flaton thesurface, theopposite wingtip

shouldbe proppedup soit is3′′ fromthe surface.Apply more

maskingtape tothe centerwing jointand recheckthe 3′′

measurement.Allow thewing jointto dryovernight.

Note: Itis helpfulto usewax paperunderneath thewing

centerwhile theepoxy iscuring sothe excessepoxy

doesnot adhereto thework area’ssurface.

Step 12. Allow the wing center joint to completely cure, then

removethe maskingtape.

Step 13. Locate the plywood wing dowel plate and use 6-

minuteepoxy toepoxy itin placeon thefront ofthe wing.When

installingthe plywooddowel plate,care shouldbe givento line

upthe holesin thewing andthe plateas closelyas possible.The

holeswill needto betrimmed outto allowthe dowelsto fit.

Step 14. Using 6-minute epoxy, epoxy the two wood dowels in

placesuch that1/2′′ isexposed.

CONTINUED

Section 2: Joining the Wing Halves

plywoodwing dowelplate

Autres manuels pour Cap232

Table des matières

Autres manuels Hangar 9 Jouet

Hangar 9

Hangar 9 Taylorcraft 20cc ARF Manuel utilisateur

Hangar 9

Hangar 9 Clipped Wing Taylorcraft ARF Manuel utilisateur

Hangar 9

Hangar 9 Pulse XT 60 ARF Manuel utilisateur

Hangar 9

Hangar 9 1/4 PA-18-150 Super Cub Manuel utilisateur

Hangar 9

Hangar 9 toledo special 40 Manuel utilisateur

Hangar 9

Hangar 9 Spitfire Mk.IX ARF Manuel utilisateur

Hangar 9

Hangar 9 FuntanaS .40 Manuel utilisateur

Hangar 9

Hangar 9 F4U Corsair .60 ARF Manuel utilisateur

Hangar 9

Hangar 9 P-51D Mustang 40 ARF Manuel utilisateur

Hangar 9

Hangar 9 FuntanaX 50 Manuel utilisateur

Hangar 9

Hangar 9 P-51D 1.50 ARF Manuel utilisateur

Hangar 9

Hangar 9 Pulse 125 Manuel utilisateur

Hangar 9

Hangar 9 Twist 3D .40 Manuel utilisateur

Hangar 9

Hangar 9 HAN5065 Manuel utilisateur

Hangar 9

Hangar 9 PULSE XT 40 ARF Manuel utilisateur

Hangar 9

Hangar 9 Advance 40 Manuel utilisateur

Hangar 9

Hangar 9 YAK 54 89 Manuel utilisateur

Hangar 9

Hangar 9 showtime 4d 90 Manuel utilisateur

Hangar 9

Hangar 9 ARROW Manuel utilisateur

Hangar 9

Hangar 9 Taylorcraft 26cc Hangar 9 Manuel utilisateur

Hangar 9

Hangar 9 Ultra Stick 40 ARF Manuel utilisateur

Hangar 9

Hangar 9 1/5 Spitfire Mk IXc 30cc Manuel utilisateur

Hangar 9

Hangar 9 RV-8 Manuel utilisateur

Hangar 9

Hangar 9 Hangar 9 P-51 Mustang ARF Manuel utilisateur

Manuels Jouet populaires d'autres marques

marklin

marklin 37321 Manuel utilisateur

Canon

Canon PAPER CRAFT Manuel utilisateur

GREAT PLANES

GREAT PLANES Pitts M-12S Manuel utilisateur

NOCH

NOCH 14261 Manuel utilisateur

Hausler

Hausler 450 SE V2 Manuel utilisateur

Dynaflite

Dynaflite Daydream Manuel utilisateur

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuel

Kenner

Kenner Batman 63651 Manuel utilisateur

LEGO

LEGO 8527 Manuel utilisateur

iKarus

iKarus ECO 8 Manuel utilisateur

Multiplex

Multiplex EasyStar II Mode d’emploi

Walkera

Walkera 38 Mode d’emploi

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuel utilisateur

MD MXION SWD Manuel utilisateur

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuel utilisateur

marklin

marklin 39671 Manuel utilisateur

Meccano

Meccano 15103 Manuel utilisateur

LEGO

LEGO TECHNIC 8735 Manuel utilisateur