handi quilter QT09726 Manuel utilisateur
Page 1
Installation Instructions
for HQ Sit-down Table Extension
Box Contents:
(1) 18” x 30” table extension Leaf
(1) Hinge assembly
(2) Hinge clips (1 left and 1 right)
(2) Plastic snap shims
(12) #10 x 5/8” Phillips Screws
Tools needed:
#2 Phillips screwdriver
Long straight edge
Note:
The HQ Sit-down Table Extension can be installed on either
the left-hand or right-hand side of the table.
Install the Hinge Assembly
1. Fold the table legs up, ip the table over and lay it on the
oor on a soft surface (to avoid damaging the table). Iden-
tify which side will receive the extension and identify the 2
screws that hold the side spacer block to the table
(Figure 1).
2. Using the #2 Phillips screwdriver, remove the 2 screws
and remove the spacer block from the table (Figure 1).
3. Place the hinge assembly (Figure 2) into the table, posi-
tioned with the metal slots down against the top of the table
as shown in Figure 3. Line up the holes and replace the
original screws. Tighten screws rmly. Note: Metal slots
will extend slightly beyond the table edge.
Copyright Handi Quilter, Inc. 2011
Figure 2
Figure 3
02/14/2011
Figure 1
Remove these screws
Page 2
Figure 4
Figure 5
Figure 6
Attach Hardware to Table Extension Leaf
4. Inspect the table extension leaf and orient it so that the
seam in the edge banding is to the rear of the table and the
pre-drilled holes are facing upward. While the table is at
and upsidedown on the oor, position the table extension
leaf at the side of the table (Figure 4).
5. Inspect the 2 hinge clips and orient them with the pins
facing inward towards each other and the bent hook point-
ing up and toward the table. Gently lift the table and slide
the bent hook into the hinge slots (Figure 5).
6. Make sure the leaf is tight against the table top and then
place a straight edge against the front of the table to line up
the front edge of the leaf (Figure 6).
7. Pull the hinge clips away from the table and align holes in
clips with holes in table extension leaf. Avoiding the center
set of holes, place screws in remaining holes as shown in
Figure 7 (three screws per hinge) and tighten the screws
into the pre-drilled holes in the extension leaf.
Figure 7
Page 3
Figure 9
Figure 10
8. Using the remaining screws, attach the plastic snap
shims to the underside of the table extension leaf as shown
in Figure 8 with the lower angled side facing inward.
9. Remove table extension leaf from table, invert table and
extend the legs securely.
Attaching the Table Extension to the Table
10. Insert the table extension leaf hinge clips into the slots
as shown in Figure 9 and raise the leaf to a horizontal posi-
tion (Figure 10).
11. Pivot the 2 hinge braces out until they snap into place in
the plastic snap shims (Figure 11).
Figure 8
Figure 11
Page 4
Lowering the Table Extension Leaf
12. Press the snap button on the plastic snap shim and piv-
ot the hinge braces inward. Once the braces are unlocked,
hold the extension leaf with one hand and pivot the braces
to the closed position (Figure 12).
13. Gently lower the table extension (Figure 13).It is safe
to allow it to hang in this position until needed.
Removing the Table Extension from the Table
14. The table extension may also be removed for storage.
To remove extension, place one hand on each side of table
extension and gently rotate slightly while lifting upward to
release hinge hooks from the hinge slots (Figure 14).
Note: DO NOT lift table by lifting on extension!
Figure 12
Figure 13
Figure 14
Optional Accessory: Open-Toe Hopping Foot
Great for increased visibility for intricate quilting or outlin-
ing applique shapes. Available from your local HQ Rep or
order online at www.HandiQuilter.com.
Table des matières
Autres manuels handi quilter Accessoires pour machines à coudre
handi quilter
handi quilter Sixteen P-Pod Manuel utilisateur
handi quilter
handi quilter HQ Pro-Stitcher Premium Manuel utilisateur
handi quilter
handi quilter TruStitch Manuel utilisateur
handi quilter
handi quilter HQ Simply Sixteen Guide de référence
handi quilter
handi quilter HQ Amara Manuel utilisateur
Manuels Accessoires pour machines à coudre populaires d'autres marques
JUKI
JUKI IP-200 Guide de l'utilisateur
Sullivans
Sullivans Sew & Go Manuel utilisateur
Sailrite
Sailrite ULTRAFEED 120931 Manuel utilisateur
Bernina
Bernina Spanish Hemstitch Equipment 47 Manuel utilisateur
Brother
Brother ScanNCut DX Stamp Starter Kit Manuel utilisateur
ELNA
ELNA 495-526-20 Manuel utilisateur