HAMPTON BAY 134674 Manuel utilisateur

Hampton Bay Lifetime Limited Warranty

The retailer warrants the fan motor to be free from defects in workmanship and material

present at time of shipment from the factory for a lifetime after the date of purchase by the

original purchaser. The retailer also warrants that all other fan parts, excluding any glass or

plexiglass blades, to be free from defects in workmanship and material at the time of

shipment from the factory for a period of one year after the date of purchase by the original

purchaser. We agree to correct such defects without charge or at our option replace with a

comparable or superior model if the product is returned to the retailer. To obtain warranty

service, you must present a copy of the receipt as proof of purchase. All costs of removing

and reinstalling the product are your responsibility. Damage to any part such as by accident

or misuse or improper installation or by affixing any accessories, is not covered by this

warranty. Because of varyingclimatic conditions inthe United States this warranty does not

cover any changesin brass finish, including rusting, pitting, corroding, tarnishing orpeeling.

Brass finishes of this type give their longest useful life when protectedfrom varying weather

conditions. A certain amount of wobble is normal and should not be considered a defect.

Servicing performed by unauthorized persons shallrender the warranty invalid. There is no

other express warranty. The retailer hereby disclaims any and all warranties,

including but not limited to. Those of merchantability and fitness for a particular

purpose to the extent permitted by law. The duration of any implied warranty which

cannot be disclaimedis limited to the time period as specified inthe express warranty. Some

states do not allow limitation on how long an implied warranty lasts, so the above limitation

may not apply to you. The retailer shall not be liable for incidental, consequential, or

special damages arising out of or in connection with product use or performance except

as may otherwise be accorded by law. Some states do not allow theexclusion of incidental

or consequential damages, so the above exclusion or limitation may not apply to you. This

warranty gives specific legal rights, and you may also have other rights which vary from

state to state. This warranty supersedes all priorwarranties.

Lifetime Limited Warranty

Date Purchased

Store Purchased

Model No.

Serial No.

Vendor No.

UPC

181-236

14826

792145350224

Safety Rules.....................................................................................................................................

Unpacking Your Fan ........................................................................................................................

Installing Your Fan ...........................................................................................................................

Installing the Light Kit......................................................................................................................

Care of Your Fan ...........................................................................................................................

Troubleshooting ............................................................................................................................

Specifications ...............................................................................................................................

Operating Your Transmitter...............................................................................................................

10.

11.

12.

13.

Table of Contents

1. To reduce the risk of electric shock, insure electricity has been turned

off at the circuit breakeror fuse boxbefore beginning.

2. All wiring must be in accordance with the National Electrical Code and

local electrical codes. Electrical installation should be performed by a

qualified licensed electrician.

3. WARNING: To reduce the risk of electrical shock and fire, do not use

this fan withany solid-state fanspeed control device.

4. WARNING: To reduce the riskof personal injury, use only the two steel

screws (and lock washers) provided with the fan for mounting to the

outlet box. Most outlet boxes commonly used for the support of lighting

fixtures are not acceptable for fan support and may need to be replaced,

consult a qualifiedelectrician if indoubt.

7. Avoid placing objects in the path of the blades.

8. Reverse thefan while themotor is onany speeds.

9. To avoid personal injury or damage to the fan and other items, be

cautious when workingaround or cleaningthe fan.

10. Do notuse water ordetergents when cleaningthe fan or fan blades. A

dry dust cloth or lightly dampened cloth will be suitable for most

cleaning.

11. After marking electrical connections, spliced conductors should be

turned upward and pushed carefully up into outlet box. The wires

should be spread apart with the grounded conductor and the

equipment-grounding conductor onone side ofthe outlet box.

12. Electrical diagrams are for reference only. Light kit that are not

packed with the fan must be CUL Listed and marked suitable for use

with the model fan you areinstalling. Switches must be CUL General

Use Switches. Refer to the Instructions packaged with the light kits

and switches forproper assembly.

WARNING

TO REDUCETHE RISK OFFIRE, ELECTRIC SHOCKOR PERSONAL

INJURY, MOUNT FAN TO OUTLET BOX MARKEDACCEPTABLE FOR

FAN SUPPORT.

5. The outlet box and support structure must be securely mounted and

capable of reliably supporting a minimum of 50 pounds. Use only CUL

Listed outlet boxesmarked FOR FAN SUPPORT.

6. The fan must be mounted with a minimum of 7 feet clearance from the

trailing edge ofthe blades tothe floor.

WARNING

TO REDUCETHE RISK OFPERSONAL INJURY, DO NOTBEND THE

BLADE BRACKETS (ALSOREFERRED TOAS FLANGES)DURING

ASSEMBLYOR AFTERINSTALLATION. DO NOTINSERT OBJECTS IN

THE PATHOF THE BLADES.

NOTE

READ AND SAVE ALLINSTRUCTIONS!

1. Safety Rules

Unpacking Your Fan 2.

Unpack your fanand check thecontents. You should havethe following items:

2. Canopy assembly

Set of blades(5)

Ball/downrod assembly (1)

& extra downrod(1)

Decorative scroll

5. Fan motorassembly

6. Set ofblade bracket (5 )

7. Switch housing

8. Light kit

(4 )

Receiver+6 wire nuts

11. Transmitter+holder+2 mounting screws

Extra collar cover

Balancing kit

9. Glass shade

10.

12.

13.

LIGHT / DIMMER

LO MED HI

FAN OFF

REVERSE

ONON

WARNING

DO NOT INSTALL ORUSE FAN

IF ANYPARTIS DAMAGED OR MISSING.

CALL TOLLFREE 877-902-5588

NOTE

FOR NON-LIGHT USEPURPOSE, THE

SWITCH HOUSING COVERIS AVAILABLE

BY CALLINGTHE TOLLFREE NUMBER

877-902-5588

14. Loose partsbag containing:

b. Blade attachmenthardware

()

a. Mounting hardware

crews (2 PCs.)

Lock washers (2PCs.)

Metal washers (2PCs.)

Plastic wire connectors(3 PCs.)

16 screws, 16fiber washers

3. Installing Your Fan

Tools Required

Phillips screwdriver, straight slot

screwdriver, adjustablewrench, step ladder,

and wire cutters.

Mounting Options

If there isn't an existing CUL listed

mounting box, then read the following

instructions. Disconnect the power by

removing fuses or turning off circuit

breakers.

Secure the outlet box directly to the

building structure. Use appropriate

fasteners and buildingmaterials. The outlet

box and its support must be able to fully

support the moving weight of the fan (at

least 50 lbs). Do not use plastic outlet

boxes.

Figures 1,2 and 3 are examples of different

ways to mountthe outlet box.

Note: You may need a longer downrod to

maintain proper blade clearance when

installing on asteep, sloped ceiling.

To hang your fan where there is an existing

fixture but no ceiling joist, you may need an

installation hanger bar as shown in Figure 4

(available at yourHampton Bay Retailer).

Outlet box

Provide strong

support

Recessed

outlet box

Mounting bracket

opening must be

toward the top

Outlet box

Figure 1 Figure 3

Figure 2

Figure 4

Angled ceiling

maximum

18 angle

Hanging the Fan

REMEMBER to turn off the power. Follow

the steps belowto hang yourfan properly:

Step 1. Remove the decorative canopy

bottom cover from the canopy by turning the

cover counter clockwise.(Fig.5)

Step 2. Remove the hanger bracket from the

canopy by loosening the two screws on the

bottom of the hanging bracket

from the screw head and turning the canopy

counter clockwise. (Fig,5)

Step 3. Pass the 120-volt supply wires

through the center hole in the ceiling hanger

bracket as shownin Fig. 6.

Step 4. Secure the hanger bracket to the

ceiling outlet box with the screws and

washers provided withyour fan.

Step 5. Remove the hanger pin, lock pin and

set screws from the top of the motor

assembly.

Step 6. Route wires exiting from the top of

the fan motor through the decorative scroll,

canopy cover, canopy and then through the

ball / downrod.(Fig. 7)

Step 7. Align the holes at the bottom of the

downrod with theholes in the collar on top of

the motor housing (Fig.7). Carefully insert

a half turn

WARNING

FAILURETO PROPERLY INSTALL LOCKINGPIN

AS NOTED INSTEP 7 COULD RESULT IN FAN

LOOSENING ANDPOSSIBLYFALLING.

Step 8. Tighten twoset screws ontop of the fan

motor firmly (Figure7)

Step 9. Place the downrod ball into the hanger

bracket socket.

the hanger pin through the holes in the collar

and downrod. Be careful not to jam the pin

against the wiring inside the downrod. Insert

the locking pin through the hole near the end

of the hanger pin until it snaps into its locked

position, as notedin the circleinset of Fig. 7.

Mounting

screws

(supplied with

the fan)

Hook

Ceiling

mounting

plate

CUL Listed

electrial

box

Figure 6 120V Wires

Washers

Figure 5

Ceiling

mounting

plate

Ceiling

canopy

Canopy

cover

CHANGING THE DOWNROD

NOTE: Your fan comes with a 6" downrod

attached to the hanging ball for not to use the

decorative scroll in lower ceiling (See Fig. 7A).

In addition, you have been provided with a 12"

downrod to use with the decorative scroll (See

Fig. 7)

Installing the fan with decorative

scroll (with 12" downrod)

(Recommend min. 9 ft. ceiling height)

1.Remove the hanger ball from the 6"downrod by

loosening the set screw at the top of the

downrod which holds the hanger ball to the

downrod.

2.Slide the hanger ball down the downrod

and remove the support pin.

3.Reinstall the ball to the 12" downrod.

4.Follow the Fig. 7 and continue on section

titled "Hanging the Fan" for installation.

Make the Electric

Connections

WARNING: To avoid possible electrical shock,

be sure electricity is turned off at the main fuse

box before wiring.

NOTE: This remote control unit is equipped

with 16 code combinations to prevent possible

interference from or to other remote units. The

frequency switches on your receiver and

transmitter have been preset at the factory.

Please recheck to make sure the switches on

transmitter and receiver are set to the same

position, any combination of settings will

operate the fan as long as the transmitter and

receiver are set to thesame position.(Figure 9)

Step 1. (Figure 10) Insert the receiver into the

mounting bracket with the flat side of the

receiver facing the ceiling.

Step 2. (Figure 11) Motor to Receiver

Electrical Connections: Connect the black

wire from the fan to black wire marked "TO

MOTOR L". Connect the white wire from

the fan to the white wire marked "TO MOTOR

N" from the receiver. Connect the blue wire

from the fan to the blue wire marked "For

Light" from the receiver. Secure the wire

connections with the plastic wire nuts provided.

Step 3. (Figure 11) Receiver to House Supply

Wires Electrical Connections: Connect the

black (hot) wire from the ceiling to the black

wire marked "AC in L" from the receiver.

Connect the white(neutral) wire from the

ceiling to the white wire marked "AC in N"

from the Receiver. Secure the wire connections

with the plastic wire nuts provided.

Figure 8

Safety Cable

INSTALLATION OF SAFETY SUPPORT

An additional safety support is provided to

prevent the fan from falling. Secure the

safety cable to the ceiling joist with screw

and washer,as illustrated in Figure 8.

Pin in

locked

position

Motor collar

Motor wires

Ball/downrod

assembly

Ceiling

canopy

Tighten

screws

firmly

Figure 7

Hanger pin

Locking pin Decorative scroll

Canopy

cover

Pin in

locked

position

Motor collar

Motor wires

Ball/downrod

assembly

Ceiling

canopy

Tighten

screws

firmly

Figure 7A

Hanger pin

Locking pin Collar cover

Canopy

cover

With 12" Downrod With 6" Downrod

Installing the fan without

decorative scroll (with 6" downrod)

(Recommend min. 8.25 ft. ceiling height)

1.Remove the hanger pin, lock pin and set

screws from the top of the motor

assembly.

2.Route wires exiting from the top of the

fan motor through the collar cover,

canopy cover, canopy and then through

the ball/downrod (Fig.7A)

3.Follow the steps 7,8,9 in section titled

"Hanging the Fan"for installation.

Finishing the Installation

Step 1. Tuck connections neatly into ceiling

outlet box.

Step 2. Slide the canopy up to ceiling and over

the 2 screws on hanger bracket. Rotate canopy

clockwise, next, while holding the canopy with

one hand, slidethe canopy cover over the screws

and rotate clockwise until tight. Note: adjust

the canopy screws as necessary until the canopy

and canopy coverare snug. (Fig.12)

Figure 12

Outlet box

Hanger

bracket

Canopy

cover

Screws

SUPPLYCIRCUIT

Ground

Conductor

Outlet Box

Green

Ground

Lead

Ground to

Downrod

BLACK

WHITE

BLACK

BLUE

GREEN

Figure 11

WHITE

BLUE

BLACK

ONON

Figure 10

Receiver

Hanger

bracket

ONON

Figure 9

Code switch

WARNING

MAKE SURE TAB AT BOTTOM OFHANGER

BRACKET IS HANGERPROPERLYSEATED IN

GROOVE OF HANGERBALL BEFORE

ATTACHING CANOPYTO BRACKET. FAILURE

TO PROPERLY SEAT TAB IN GROOVE COULD

CAUSE DAMAGE TOELECTRICAL WIRING.

Step 4. (Figure 11) If your outlet box has a

ground wire (green or bare copper) connect it

To the fan ground wires; otherwise connect

the hanging bracket ground wire to the

mounting bracket. Secured the wire

connection with a plastic nut provided. After

connecting the wires spread them apart so

that the green and white wires are on one side

of the outlet box and black and blue wires are

on the other side. Carefully tuck the wire

connections up into the outlet box.

Attaching the Fan

Blades

Step 1 Attach blades to blade brackets using

three screws and fiber washers as shown in

Figure 13. Start a screw intothe bracket, donot

tighten. Repeat for the 2 remaining screws and

washers.

Step 2 Tighten each screw securely , make sure

the blade isstraight.

Step 3 Fasten the blade brackets to the motor

by inserting the tab from the blade brackets to

the slot in the bottom motor housing, then

tighten the two screws and washers already

installed in theblade brackets. (Figure 14)

Step 4 Install an optional light kit if you wish.

Follow the instructionsincluded with the kit.

All blades are grouped by weight. Because

natural woods very in density, the fan may

wobble even though the blades are weight

matched.

The following procedure should correct

most fan wobble. Check after eachstep.

1. Check that all blade and blade bracket

screws are secure.

2. Most fan wobble problems are caused

when blade levels are unequal. Check this

level by selecting a point on the ceiling

above the tip of one of the blades. Measure

this distance as shown in Figure 15. Rotate

the fan until the next blade is positioned for

measurement. Repeat for each blade. The

distance should be equal within

1/8".

If all blade levels are not equal, you can

adjust the blade level with the following

procedure.

deviation

Fiber

washer

Blade

bracket

Figure 13

Blade

Screws

Figure 14

Motor

Blade bracket

Slot

Tab

To Adjust the blade tip down, insert a

washer (not supplied) between the blade and

blade bracket at the screw closest to the

motor (Figure 16)

To adjust the blade tip up, insert a washer

(not supplied) between the blade and blade

bracket at the two screws farthest from the

motor (Figure 16)

3. Use the enclosed Blade Balancing Kit if

the blade wobbleis still noticeable.

4. If the blade wobble is still noticeable,

interchanging two adjacent (side by side)

blades can redistribute the weight and

possibly result insmoother operation.

WARNING

TO REDUCE THERISK OF PERSONALINJURY,

DO NOT BENDTHE BLADE HOLDERS

WHILE INSTALLING,BALANCING THE

BLADES, OR CLEANINGTHE FAN. DO NOT

INSERT FOREIGNOBJECTS BETWEEN

ROTATING FANBLADES.

Figure 16

Fan blade

blade tip down

Fan blade

blade tip up

Blade

bracket

Touching

ceiling

Figure 15

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels HAMPTON BAY Ventilateur

HAMPTON BAY

HAMPTON BAY GLENDALE III AK488-MBK Manuel utilisateur

HAMPTON BAY

HAMPTON BAY AL663A-LN Manuel utilisateur

HAMPTON BAY

HAMPTON BAY Portsmouth Manuel utilisateur

HAMPTON BAY

HAMPTON BAY Farmington Manuel utilisateur

HAMPTON BAY

HAMPTON BAY 553-295 Manuel utilisateur

HAMPTON BAY

HAMPTON BAY OSCW-24M BK Manuel utilisateur

HAMPTON BAY

HAMPTON BAY Irondale 1969 Manuel utilisateur

HAMPTON BAY

HAMPTON BAY Windward II 523 342 Manuel utilisateur

HAMPTON BAY

HAMPTON BAY 52-RDT Manuel utilisateur

HAMPTON BAY

HAMPTON BAY Lindbrook YG336-BN Manuel utilisateur

HAMPTON BAY

HAMPTON BAY LELAND II Manuel utilisateur

HAMPTON BAY

HAMPTON BAY RENWICK 656 416 Manuel utilisateur

HAMPTON BAY

HAMPTON BAY Capella AM113-BN Manuel utilisateur

HAMPTON BAY

HAMPTON BAY 1005 819 968 Manuel utilisateur

HAMPTON BAY

HAMPTON BAY BANNERET YG730-MWH Manuel utilisateur

HAMPTON BAY

HAMPTON BAY LOOMIS YG990-MBK Manuel utilisateur

HAMPTON BAY

HAMPTON BAY Trusseau 324-683 Manuel utilisateur

HAMPTON BAY

HAMPTON BAY 1002 498 557 Manuel utilisateur

HAMPTON BAY

HAMPTON BAY 32711 Manuel utilisateur

HAMPTON BAY

HAMPTON BAY Savona Tiffany Manuel utilisateur

HAMPTON BAY

HAMPTON BAY VERANDA 499-493 Manuel utilisateur

HAMPTON BAY

HAMPTON BAY AC457-WH Manuel utilisateur

HAMPTON BAY

HAMPTON BAY 7134-01 Manuel utilisateur

HAMPTON BAY

HAMPTON BAY Farmington Manuel utilisateur

Manuels Ventilateur populaires d'autres marques

ELTA FANS

ELTA FANS H03VV-F Manuel utilisateur

Hunter

Hunter 20714 Manuel d'instructions

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuel utilisateur

Hunter

Hunter Caraway Manuel d'instructions

Panasonic

Panasonic FV-15NLFS1 Manuel utilisateur

Kompernass

Kompernass KH 1150 Manuel utilisateur

VES

VES FALA100/12V/TR Manuel utilisateur

Vertiv

Vertiv Liebert DCD Manuel utilisateur

Westinghouse

Westinghouse GFP Series Manuel utilisateur

Venmar

Venmar KUBIX HRV PLUS Series Manuel utilisateur

Maico

Maico ECR 31 Manuel utilisateur

Sonnenkonig

Sonnenkonig Dinky Manuel utilisateur

S&P

S&P ECOWATT HXBR Manuel utilisateur

Wider

Wider IMP03369BH Manuel utilisateur

Panasonic

Panasonic F-60DHN Manuel utilisateur

Hinkley

Hinkley HIGHLAND Manuel utilisateur

Broan

Broan 766BN Manuel utilisateur

Premium

Premium PFS16022 Instructions de montage