Haier GE Profile UltraFresh GFW650S Guide de configuration

99-3000289

Part Install Instructions

Overview –Procedure for programming new Main Boards when all

LEDs are flashing.

GE and Profile UltraFresh™Front Load Washer Main Board

!IMPORTANT SAFETY NOTICE

The information in this part instruction is intended for use by

individuals possessing adequate backgrounds of electrical,

electronic and mechanical experience. Any attempt to repair a

major appliance may result in personal injury and property damage.

The manufacturer or seller cannot be responsible for the

interpretation of this information, nor can it assume any liability in

connection with its use.

!WARNING

To avoid personal injury, disconnect power before servicing this

appliance. If electrical power is required for diagnosis or test

purposes, disconnect the power immediately after performing the

necessary checks. RECONNECT ALL GROUNDING DEVICES If

grounding wires, screws, straps, clips, nuts, or washers used to

complete a path to ground are removed for service, they must be

returned to their original position and properly fastened.

Parts Included:

•Main Board •Instruction Sheet

1. Press and release the Start button. LEDs will stop flashing and the display

should show “0”.

2. Press and release the Start button until the display shows the number of the

personality ID needed.

▪When the end of the ID list is reached the control will wrap around to the

beginning of the personality ID number list.

3. Press and hold the Start button for three seconds when the correct personality

ID number needed is in the display.

▪This will save the personality ID number and the control will go to an idle

state.

NOTE: If an error is made programming the Main Board or the LEDs are not flashing, enter Field

Service Mode as shown on the last page of these instructions. Use service mode test 17 to enter

the correct personality. 1

Model # Personality ID #

GFW650S* 3

GFW850S* 4

PFW950S* 6

FIELD SERVICE MODE ENTRY

Press and hold Start button while rotating the

cycle selection knob 180 degrees and then

release the Start button.

• Once service mode is entered all LEDs will

be flashing.

• The cycle selection Knob is now used to

control the test selection menu.

–Rotating the knob clockwise will increment

the test numbers in the

display.

–Rotating the knob counter-clockwise will

decrement the test number in the display.

–Turning the knob to go to a different test will

terminate any current active state

• Once the test number is selected, pressing

Start will begin the selected test.

• Once the test number is selected, pressing Start

will begin the selected test.

Exit Field Service Mode

•Field service mode will time out after 30 minutes

if there is no user activity.

•Press Power button

SERVICE MODE TEST 17 -

Change Personality

Pressing Start will start the test. Press Start

button again and the next valid personality should

be displayed. Press and hold the Start button to

select the correct personality. The control will go to

an idle state. All LEDs off.

Note: If the personality ID is already set and you

try to set the same personality the control will

NOT go to an idle state. Ensure the correct

personality ID is being entered.

99-3000289

Ce manuel convient aux modèles suivants

Autres manuels Haier Rondelle

Haier

Haier XQBM22-C Manuel utilisateur

Haier

Haier XPB80-50 Manuel utilisateur

Haier

Haier HWM100-FD10829 Manuel utilisateur

Haier

Haier HW-F1481 ME Manuel utilisateur

Haier

Haier XPB52-33 Manuel utilisateur

Haier

Haier HWM75-B12266 Manuel utilisateur

Haier

Haier HMS1002AA Manuel utilisateur

Haier

Haier HW120-B14686-F Manuel utilisateur

Haier

Haier HWM180-M1990DD Manuel utilisateur

Haier

Haier HW-B1270 Manuel utilisateur

Haier

Haier HW-C870TVE Manuel utilisateur

Haier

Haier HW80-B1239N Manuel utilisateur

Haier

Haier HNS1250TVE Guide de démarrage rapide

Haier

Haier HWM20-0701 Manuel utilisateur

Haier

Haier XPB72-276S Manuel utilisateur

Haier

Haier HW80-B14979 Manuel utilisateur

Haier

Haier HW-C1050TVE Manuel utilisateur

Haier

Haier HW-B1060 Manuel utilisateur

Haier

Haier HW120-B14686 Series Manuel utilisateur

Haier

Haier HWM108VA Manuel utilisateur

Haier

Haier HW-F1060TVE Manuel utilisateur

Haier

Haier HBF855TVE Manuel utilisateur

Haier

Haier HBF600T Manuel utilisateur

Haier

Haier HW60-12829S Manuel utilisateur

Manuels Rondelle populaires d'autres marques

Tricity Bendix

Tricity Bendix AW 1000 W Guide produit

Panasonic

Panasonic NA-F60L5WRB Manuel utilisateur

GE WSLP1500 Manuel

Electrolux

Electrolux EWF1284EDW Manuel utilisateur

Bosch

Bosch WAN2829BSN Manuel utilisateur

LG TV2516DV3B Manuel utilisateur

LG TH2517DSAV Manuel utilisateur

VESTEL

VESTEL CMH-XL 7510 TE Manuel utilisateur

AEG

AEG 74335 Manuel d'utilisation

Johnson

Johnson JWF721A Manuel utilisateur

Beko

Beko WTE7604XLW0 Manuel utilisateur

Danby

Danby DTT100A1WDB Instructions de montage

Amica

Amica WA 14 Ex Manuel utilisateur

Daewoo

Daewoo DWD-F1222 Manuel utilisateur

Bosch

Bosch WAS28461AU Manuel utilisateur

Miele

Miele PW 6080 Vario Manuel utilisateur

Finlux

Finlux FLX108CF220 Manuel utilisateur

Whirlpool

Whirlpool 3LBR5132AN0 Manuel utilisateur