H3C LSQM1QGS8A0 Manuel utilisateur
1
H3C LSQM1QGS8A0 interface card
user manual-6PW102
▌Introduction
Overview
The LSQM1QGS8A0 interface card provides eight QSFP+ ports.
Figure 1 LSQM1QGS8A0 interface card front panel
(1) QSFP+ port LED (2) QSFP+ port
NOTE:
The LSQM1QGS8A0 interface card is currently applicable only to
H3C S7502E-XS and S7504E-XS switches. The applicable
switch models might change over time. For the most recent list o
f
applicable switch models, contact H3C Support or marketing
staff.
QSFP+ ports
You can install QSFP+ transceiver modules in Table 1 and Table 2,
QSFP+ DAC cables in Table 3, QSFP+ to SFP+ DAC cables in Table
4, and QSFP+ optical cables in Table 5 in the QSFP+ ports on the
LSQM1QGS8A0 interface card.
2
Table 1 QSFP+ transceiver modules available for the QSFP+
ports (1)
QSFP+ transceiver module Central wavelength
(nm) Connector
QSFP-40G-SR4-MM850 850 MPO
QSFP-40G-CSR4-MM850 850 MPO
QSFP-40G-LR4-WDM1300
Four lanes:
•1271
•1291
•1311
•1331
LC
QSFP-40G-LR4L-WDM1300
Four lanes:
•1271
•1291
•1311
•1331
LC
QSFP-40G-BIDI-SR-MM850 850 LC
QSFP-40G-ER4-WDM1300
Four lanes:
•1271
•1291
•1311
•1331
LC
Table 2 QSFP+ transceiver modules available for the QSFP+
ports (2)
QSFP+
transceiver
module
Cable/fiber
diameter
(µm)
Modal
bandwidth
(MHz × km)
Max transmission
distance
QSFP-40G-SR
4-MM850
Multi-mode,
50/125
2000 100 m (328.08 ft)
4700 150 m (492.12 ft)
3
QSFP+
transceiver
module
Cable/fiber
diameter
(µm)
Modal
bandwidth
(MHz × km)
Max transmission
distance
QSFP-40G-CS
R4-MM850
Multi-mode,
50/125
2000 300 m (984.25 ft)
4700 400 m (1312.33 ft)
QSFP-40G-LR4
-WDM1300
Single-mode,
9/125 N/A 10 km (6.21 miles)
QSFP-40G-LR4
L-WDM1300
Single-mode,
9/125 N/A 2 km (1.24 miles)
QSFP-40G-BID
I-SR-MM850
Multi-mode,
50/125
2000 100 m (328.08 ft)
4700 150 m (492.12 ft)
QSFP-40G-ER
4-WDM1300
Single-mode,
9/125 N/A 40 km(24.84 miles)
Table 3 QSFP+ DAC cables available for the QSFP+ ports
QSFP+ DAC cable Cable length Data rate
LSWM1QSTK0 1 m (3.28 ft)
40 Gbps
LSWM1QSTK1 3 m (9.84 ft)
LSWM1QSTK2 5 m (16.40 ft)
Table 4 QSFP+ to SFP+ DAC cables available for the QSFP+
ports
QSFP+ to SFP+
DAC cable Cable length Data rate
LSWM1QSTK3 1 m (3.28 ft)
40 Gbps
LSWM1QSTK4 3 m (9.84 ft)
LSWM1QSTK5 5 m (16.40 ft)
4
Table 5 QSFP+ optical cables available for the QSFP+ ports
QSFP+ optical cable Cable length Data rate
QSFP-40G-D-AOC-7M 7 m (22.97 ft)
40 Gbps
QSFP-40G-D-AOC-10M 10 m (32.81 ft)
QSFP-40G-D-AOC-20M 20 m (65.62 ft)
NOTE:
H3C recommends that you use H3C QSFP+ transceiver
modules, QSFP+ DAC cables, QSFP+ optical cables, or QSFP+
to SFP+ DAC cables for the QSFP+ ports on the LSQM1QGS8A0
interface card. The QSFP+ transceiver modules, QSFP+ DAC
cables, QSFP+ optical cables, and QSFP+ to SFP+ DAC cables
available for the interface card are subject to change over time.
For the most recent list of QSFP+ transceiver modules, QSFP+
DAC cables, QSFP+ optical cables, and QSFP+ to SFP+ DAC
cables available for the interface card, contact H3C Support or
marketing staff.
For more information about H3C QSFP+ transceiver modules,
QSFP+ DAC cables, QSFP+ optical cables, and QSFP+ to SFP+
DAC cables, see H3C Transceiver Modules User Guide
at www.h3c.com.
LEDs
Table 6 describes QSFP+ port LEDs on the front panel.
Table 6 QSFP+ port LED description
LED status Description
Steady green
A transceiver module is installed in the port. The
port is operating at 40 Gbps, and a link is
present on the port.
Flashing green The port is sending or receiving data at 40 Gbps.
Steady yellow
A transceiver module is installed in the port. The
port is operating at 10 Gbps, and a link is
present on the port.
Flashing yellow The port is sending or receiving data at 10 Gbps.
5
LED status Description
Off No transceiver module is installed in the port, or
no link is present on the port.
NOTE:
The QSFP+ port LEDs are not affected by the port mode
switching button on your switch. For more information about the
port mode switching button, see the installation guide of the
switch.
▌Installing and removing an interface card
CAUTION:
•Before you install or remove an interface card, wear an ESD
wrist strap and make sure the strap makes good skin contact
and is reliably grounded.
•To avoid device damage, do not use excessive force when you
install or remove an interface card.
Installing an interface card
Before you install an interface card, remove the filler panel (if any)
from the target slot. Keep the removed filler panel secure for future
use.
To install an interface card:
1. Unpack the interface card.
Figure 2 LSQM1QGS8A0 interface card
(1) Ejector lever (2) Latch
6
2. Press the latch on the interface card to release the ejector lever.
3. As shown by callout 1 in Figure 3, insert the interface card slowly
into the slot along the guide rails.
4. Rotate inward the ejector lever as shown by callout 2 in Figure 3
until the latch locks the ejector lever in place.
Figure 3 Installing an LSQM1QGS8A0 interface card
Removing an interface card
CAUTION:
•Before you remove an interface card, remove the cable from it
to avoid cable damage.
•After removing an interface card, if no new interface card is to
be installed, install the filler panel as soon as possible to
prevent dust and ensure good ventilation in the device.
To remove an interface card:
1. Prepare an anti-static bag.
2. Press the latch to release the ejector lever
3. Rotate outward the ejector lever as shown by callout 1 in Figure 4.
4. Pull out the interface card slowly out of the interface card slot, as
shown by callout 2 in Figure 4.
5. Place the removed interface card in the anti-static bag.
1
2
7
Figure 4 Removing an LSQM1QGS8A0 interface card
Installing and removing QSFP+ transceiver modules
and DAC cables
For information about installing and removing QSFP+ transceiver
modules and DAC cables, see H3C QSFP+ Transceiver
Modules/Cables Installation Guide at www.h3c.com.
Verifying the installation
After the installation is complete, identify whether the interface card is
operating correctly.
If the interface card fails to operate correctly, perform the following
steps:
1. Reinstall it following the installation procedures described in this
document.
2. If the problem persists, contact H3C Support.
▌Technical support
New H3C Technologies Co., Ltd. provides customers with
comprehensive technical support and service. If you purchase the
products from the sales agent of New H3C Technologies Co., Ltd.,
please contact our sales agent or technical personnel.
Website: http://www.h3c.com
BOM: 3101A0K5
Table des matières
Autres manuels H3C Équipement d'enregistrement
H3C
H3C LSWM2ZQP2P Manuel utilisateur
H3C
H3C LSW1XGT4P0 Manuel utilisateur
H3C
H3C LSWM2QP2P Manuel utilisateur
H3C
H3C LSQM1TGT24QSM0 Manuel utilisateur
H3C
H3C LSWM2ZSP8P Manuel utilisateur
H3C
H3C LSPM4G4T6P Manuel utilisateur
H3C
H3C LSWM18CQMSEC Manuel utilisateur
H3C
H3C SecPath NSQM2QG2GP40 Manuel utilisateur
H3C
H3C LSPM2SP2P Manuel utilisateur
H3C
H3C LSWM116FC Manuel utilisateur
Manuels Équipement d'enregistrement populaires d'autres marques
Strymon
Strymon NIGHTSKY Manuel utilisateur
Mitsubishi Electric
Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuel utilisateur
Tews Technologies
Tews Technologies TPMC465 Manuel utilisateur
Honeywell
Honeywell Excel 50 Manuel utilisateur
SeaLevel
SeaLevel COMM+8.LPCI Manuel utilisateur
Arturia
Arturia AUDIOFUSE STUDIO Manuel utilisateur
