GSM Activate 3G RF DOOR Manuel utilisateur
PAGE 1
MODEL RF - PIR
2G & 3G
GSM Door Contact Alarm
www.gsm-activate.co.uk
Page 2
Our 2G/3G GSM Door Contact Alarm is a standalone alarm system for smaller rooms
inside properties. It will alert you using GSM technology by sending you a text message
and/or phone call to your mobile phone or landline when the sensor has been broken
alerting you to a possible intrusion.
The unit is enclosed in a IP65 rated box which means it is perfectly weathered for outside
installation and has passed testing in high temperature as well as below freezing
temperatures.
PIR Specification
GSM Module Specification
● Alert Distance : 25-35mm seperation
● Detection: Dual function, magnetic door and emergency switch
● Battery Life : 6 Months
● Dimensions - L60xW32xH13mm
● Wireless Range - 20 Meters
Product Information
● GSM Frequesncy: Quadband freq 850/900/1800/1900/ 3G Model 2100Mhz
● Power Supply Voltage: 9 - 24 volts DC - 1 Amp Min
● Current used in standby mode: 60mA Max
● IP 65 Enclosure rating for outside installation
● Micro 2G or 3G Simcard
● No landline required
● Dimensions - L100 x W68 x H50mm
● Dimensions PCB Only - L95 x W67mm
● Sim Active Function
● Operating Temperature: -10…+40 °C
● Programmed by text message
● Text to test signal strength
Page 3
Instructions
Slide the simcard into the holder making sure that the clipped corner of the simcard lines
up with the clipped corner of the simcard holder as seen in the picture above.
IMPORTANT - PLEASE READ
PLEASE MAKE SURE YOU DISCONNECT THE POWER WHEN YOU FIT THE SIM
CARD THEN PLACE THE SIM CARD IN WITH THE CLIPPED CORNER FACING
UPWARDS.
PLEASE SEE PICTURE ABOVE.
Signal Strength
To help make sure that you place the unit in a suitable position you can text the unit to see
how much signal strength the detector is receiving by texting the command #SIGNAL#
The detector will perform a test on the signal strength.
You will receive a text confirming the signal strength between 0 up to 30. We strongly
recommend that you place the unit where it can receive a signal of at least 10.
You will find that with a score of less than 10 the unit will be unreliable.
Please send one message at a time and wait for the GSM detector to send you back the text
acknowledgement ‘NUMBER STORED’ before you try to add the next number.
Below is a notepad to help you remember the numbers that you have saved to your
unit in the event you need to modify or delete in the future.
#1=_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ #
#2= _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ #
#3=_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ #
Page 4
How to Programme Mobile Numbers
After inserting the simcard into the GSM module, turn the unit on and wait until you see the
GREEN LED is on. This indicates that the module has a signal and the unit is ready for
use.
Please Note - To avoid confusion we have colour coded the hash (#) and the equals (=)
symbols.
Example: (hash) (1,2 or 3) (equals) (phone number) (hash)
To programme mobile numbers into the unit you will need to send a text with the contact
numbers (maximum 3 numbers)
Example
#1=07123456789# Then send this as a text to the simcard in the unit (with your
preferred mobile number)
#2=07123456789# Then send this as a text to the simcard in the unit (with your
preferred mobile number for second contact)
#3=07123456789# Then send this as a text to the simcard in the unit (with your
preferred mobile number for third contact)
If you wish to cancel a number, follow this example
Example: (HASH) (1,2 or 3) (EQUALS) (DELETE) (HASH)
#1=DELETE# Then send this as a text to the simcard number of your unit.
PLEASE NOTE
Page 5
How to programme the SMS text message
You can now change the alarm message from “input detected” to one of your own choice.
To change the message send the text command as follows
#MESS=YOUR MESSAGE#
The detector will reply with a text message - MESSAGE STORED
PLEASE NOTE
You can only use a maximum of 19 characters including spaces for your customised
message.
Telephone Call Alerts
The Door Contact Alarm can be programmed to send you a telephone call after each text
alarm has been sent.
You will receive approximately three ring tones. The unit will then hang up automatically.
This is to prevent call charges being incurred.
To text call alerts to ON please send the text message
#CALL=ON#
The unit will reply back with the message - CALL ON
To disarm call alerts please send the text message.
#CALL=OFF#
If the call function has been set to ON you will receive a text message and shortly after a
phone call.
How to use the 2G/3G Door Contact Alarm
Once you have positioned the door contact, the system is now ready to use.
The GSM Door Contact Alarm has two modes, Alarm Mode and Auto Mode.
In alarm mode, you have to arm your alarm manually when required.
In auto mode, the alarm is always armed.
You should choose the mode most suitable to your application.
Your can select the mode you require by sending the text message to the unit as follows:
#Mode=1# Alarm Mode (default)
#Mode=2# Auto Mode
Mode 1 - Alarm Mode: #mode=1#
Alarm mode is the default mode. You will need to set the alarm to ON before it detects
movement and sends an alarm message.
To set the alarm to ON you will need to send the text message
#ALARM=ON# This will activate the alarm.
#ALARM=OFF# This will deactivate the alarm
It is important to remember that when the alarm has been triggered you will need to reset
the alarm by sending the text message #ALARM=ON# each time.
How to use the relay output
Mode 2 - Auto Mode: #mode=2#
The alarm is always armed and will trigger when movement is detected. The alarm will
automatically reset back into armed mode after 20 seconds when no movement is
detected.
(Dipswitch 2= OFF) ref page 3
The 3G Auto Dialler has a 2 amp relay output which can be used to switch on external
electric devices such as lighting, sirens etc
By texting the unit you can turn the relay ON or OFF, Below are examples on how to do
this.
#REL=ON# This will turn the relay output ON
#REL=OFF# This will turn the relay output OFF
After each operation the unit will reply with a status report REL ON/OFF
(Dipswitch 2 = ON) ref page 3
The relay can also be setup to pulse for 20 seconds when the inputs have been triggered.
To activate this mode you need to set DIPSWITCH 2 ON - ref page 3
This can be used to trigger a siren or reset other equipment.
Page 6
PAGE 7
To connect wireless door sensors you will need to go through a process so that the
devices are matched to the receiver on the dialler.
1. Hold down the pairing button on the RF Module for 3 seconds
(refer to figure 1)
2. Trigger the door switch
3. The RF module has a RED LED which will flash when pairing in complete.
Figure 1
Pairing the Wireless Door Sensors
Page 9
09/072018 AD
Quick Reference
FACTORY RESET
To set the unit back to factory settings you will need to send a text message #RESET#
Please Note - doing this will reset ALL of your parameters. Only send a reset command
when necessary.
The GREEN ready LED will flash eight times.
Dipswitch Settings
Dipswitch 1 = ON = 3G Selected
OFF = 2G Selected
Dipswitch 2 = ON = Pulse Relay (20 seconds)
OFF = Pulse Relay Off
For more technical support please browse the FAQ’s on our website www.gsm-
activate.co.uk
Alternatively email our technical support team at [email protected] and we will
do our best to respond to your querry within 24 hours Monday- Friday.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels GSM Activate Système de sécurité
GSM Activate
GSM Activate e-CO Series Manuel utilisateur
GSM Activate
GSM Activate AD-SD Manuel utilisateur
GSM Activate
GSM Activate ADRV11 Manuel utilisateur
GSM Activate
GSM Activate ECO-BEAM Manuel utilisateur
GSM Activate
GSM Activate ECO-BEAM Manuel utilisateur
GSM Activate
GSM Activate GSM 4G AUTO DIALLER PLUS Manuel utilisateur
GSM Activate
GSM Activate Alarm Pro 20 Manuel utilisateur
GSM Activate
GSM Activate 2G RF BEAM Manuel utilisateur
GSM Activate
GSM Activate ECO Series Manuel utilisateur
GSM Activate
GSM Activate GSM PT100 Manuel utilisateur
Manuels Système de sécurité populaires d'autres marques
EDM
EDM Solution 6+6 Wireless-AE Manuel utilisateur
Highway Safety Group
Highway Safety Group EA401 Manuel utilisateur
Siren
Siren LED GSM Manuel utilisateur
Detection Systems
Detection Systems 7090i Instructions de montage
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuel utilisateur
Siemens
Siemens FDM273 Manuel utilisateur