Grundfos CMBE Series Manuel utilisateur

CMBE

Installation and operating instructions

GRUNDFOS INSTRUCTIONS

English (GB)

English (GB) Installation and operating instructions

Original installation and operating instructions

CONTENTS

Page

1. General information 3

1.1 Hazard statements 3

1.2 Notes 3

2. Safety instructions 3

3. Intended use 8

3.1 Pumped liquids 8

4. System sizing 8

5. Mechanical installation 8

5.1 Installation altitude 8

6. Electrical connection 9

6.1 Cable requirements 9

6.2 Standard functional module, FM 200 10

7. Starting up the product 12

7.1 Supplement to quick guide 12

7.2 Priming and venting the product 12

7.3 Adjusting the diaphragm tank pressure 12

7.4 Shaft seal run-in 12

8. Control functions 12

8.1 Dry-running protection 12

8.2 Pressure switch 13

9. Setting the product 13

9.1 Operating panel 13

9.2 Setpoint setting 14

9.3 Start/stop of pump 14

9.4 Resetting of fault indications 14

10. Servicing the product 14

10.1 Cable requirements 14

10.2 Megging 14

11. Taking the product out of operation 14

12. Fault finding 15

13. Technical data 16

13.1 Operating conditions 16

13.2 Supply voltage 16

13.3 Overload protection 16

13.4 Cable requirements 16

14. Further product information 17

15. Disposing of the product 17

Read this document

before installing the

product. Installation and

operation must comply

with local regulations

and accepted codes of

good practice.

This appliance can be

used by children aged

from 8 years and above

and persons with

reduced physical,

sensory or mental

capabilities or lack of

experience and

knowledge if they have

been given supervision

or instruction concerning

use of the appliance in a

safe way and

understand the hazards

involved.

Children shall not play

with the appliance.

Cleaning and user

maintenance shall not

be made by children

without supervision.

English (GB)

1. General information

1.1 Hazard statements

The symbols and hazard statements below may

appear in Grundfos installation and operating

instructions, safety instructions and service

instructions.

The hazard statements are structured in the

following way:

1.2 Notes

The symbols and notes below may appear in

Grundfos installation and operating instructions,

safety instructions and service instructions.

2. Safety instructions

Mechanical installation

Electrical connection

DANGER

Indicates a hazardous situation which, if

not avoided, will result in death or serious

personal injury.

WARNING

Indicates a hazardous situation which, if

not avoided, could result in death or

serious personal injury.

CAUTION

Indicates a hazardous situation which, if

not avoided, could result in minor or

moderate personal injury.

SIGNAL WORD

Description of hazard

Consequence of ignoring the warning.

- Action to avoid the hazard.

Observe these instructions for

explosion-proof products.

A blue or grey circle with a white graphical

symbol indicates that an action must be

taken.

A red or grey circle with a diagonal bar,

possibly with a black graphical symbol,

indicates that an action must not be taken

or must be stopped.

If these instructions are not observed, it

may result in malfunction or damage to the

equipment.

Tips and advice that make the work easier.

WARNING

Electric shock

Death or serious

personal injury

- Switch off the power

supply before you start

any work on the

product.

- Make sure that the

power supply cannot

be switched on

accidentally.

WARNING

Hot liquid

Death or serious

personal injury

- To avoid leakage do

not overtighten the

pipe connections.

CAUTION

Sharp element

Minor or moderate

personal injury

- Wear personal

protective equipment.

English (GB)

CAUTION

Crushing of feet

Minor or moderate

personal injury

- Wear safety shoes

when moving the

product.

- Use lifting equipment.

CAUTION

Back injury

Minor or moderate

personal injury

- Use lifting equipment.

DANGER

Electric shock

Death or serious

personal injury

- If national legislation

requires a Residual

Current Device (RCD)

or equivalent in the

electrical installation,

this must be type B or

better, due to the

nature of the constant

DC leakage current.

The RCD must be

marked with the

following symbols:

WARNING

Electric shock

Death or serious

personal injury

- Carry out the electrical

connection in

accordance with local

regulations.

WARNING

Electric shock

Death or serious

personal injury

- Check that the power

plug delivered with the

product is in

compliance with local

regulations.

- The protective earth of

the power outlet must

be connected to the

protective earth of the

product. The plug must

therefore have the

same PE connection

system as the power

outlet. If not, use a

suitable adapter if

allowed by local

regulations.

English (GB)

Connection terminals for inputs and outputs

Starting up the product

WARNING

Electric shock

Death or serious

personal injury

- A supply disconnecting

device made according

to EN 60204-1 5.3.2

must be provided with

means permitting it to

be locked in the OFF

(isolated) position. This

device must also be

installed in a position

according to EN

60204-1, 5.3.4.

WARNING

Electric shock

Death or serious

personal injury

- Power cables without a

plug must be

connected to a supply

disconnecting device

incorporated in the

fixed wiring according

to local regulations.

WARNING

Electric shock

Death or serious

personal injury

- Comply with local

regulations as to cable

cross-sections.

DANGER

Electric shock

- Death or serious

personal injury

- Make sure that the

wires to be connected

to the connection

groups below are

separated from each

other by reinforced

insulation in their entire

lengths.

WARNING

Hot liquid

Death or serious

personal injury

- If the temperature is

higher than 50 °C, use

gloves and glasses

when venting the pump

to avoid risk of

scalding.

WARNING

Biological hazard

Death or serious

personal injury

- Flush the pump with

clean water before first

use.

English (GB)

Servicing the product

Taking the product out of operation

WARNING

Electric shock

Death or serious

personal injury

- Switch off the power

supply before you start

any work on the

product.

- Make sure that the

power supply cannot

be switched on

accidentally.

WARNING

Pressurised system

Death or serious

personal injury

- Depressurise the

system before you start

any work on the

product. The pumped

liquid may be scalding

hot and under high

pressure.

- Drain the system or

close the isolating

valves on either side of

the pump.

WARNING

Biological hazard

Death or serious

personal injury

- When servicing the

product, only use

Grundfos original

spare parts.

WARNING

Electric shock

Death or serious

personal injury

- Comply with local

regulations as to cable

cross-sections.

WARNING

Electric shock

Death or serious

personal injury

- Switch off the power

supply before you start

any work on the

product.

- Make sure that the

power supply cannot

be switched on

accidentally.

English (GB)

Fault finding

WARNING

Pressurised system

Death or serious

personal injury

- Depressurise the

system before you start

any work on the

product. The pumped

liquid may be scalding

hot and under high

pressure.

- Drain the system or

close the isolating

valves on either side of

the pump.

WARNING

Electric shock

Death or serious

personal injury

- Switch off the power

supply before you start

any work on the

product.

- Make sure that the

power supply cannot

be switched on

accidentally.

WARNING

Pressurised system

Death or serious

personal injury

- Depressurise the

system before you start

any work on the

product. The pumped

liquid may be scalding

hot and under high

pressure.

- Drain the system or

close the isolating

valves on either side of

the pump.

WARNING

Biological hazard

Death or serious

personal injury

- When servicing the

product, only use

Grundfos original

spare parts.

English (GB)

3. Intended use

3.1 Pumped liquids

The product is suitable for pumping clean, thin,

non-aggressive, non-toxic and non-explosive liquids

without solid particles or fibres.

4. System sizing

The pump is by default set to not stop until it reaches

its maximum pressure.

5. Mechanical installation

5.1 Installation altitude

The installation altitude is the height above sea level

of the installation site.

• Products installed up to 1000 m above sea level

can be loaded 100 %.

• The motors can be installed up to 3500 m above

sea level.

The motor output power (P2) in relation to the

altitude above sea level is shown in the graph below.

Fig. 1 Derating of motor output (P2) in relation

to altitude above sea level

This product has been evaluated for use

with clean water only.

Only use the product according to the

specifications stated in these installation

and operating instructions.

If the water contains sand, gravel or other

debris, there is a risk of pump blockage

and pump damage.

Please install a filter on the inlet side or

apply a floating strainer to protect the

pump.

The system in which the CME Booster is

incorporated must be designed for the

maximum pump pressure.

WARNING

Electric shock

Death or serious personal injury

- Switch off the power supply before you

start any work on the product.

- Make sure that the power supply cannot

be switched on accidentally.

WARNING

Hot liquid

Death or serious personal injury

- To avoid leakage do not overtighten the

pipe connections.

CAUTION

Sharp element

Minor or moderate personal injury

- Wear personal protective equipment.

CAUTION

Crushing of feet

Minor or moderate personal injury

- Wear safety shoes when moving the

product.

- Use lifting equipment.

CAUTION

Back injury

Minor or moderate personal injury

- Use lifting equipment.

Motors installed more than 1000 m above

sea level must not be fully loaded due to

the low density and consequent low

cooling effect of the air.

TM05 6400 4712

500 1000 1500 2000 2500 3000 3500

Altitude [m]

P2 [%]

English (GB)

6. Electrical connection

Check that the supply voltage and frequency

correspond to the values stated on the nameplate.

6.1 Cable requirements

See section 13.4 Cable requirements for more

information on cable cross-sections and conductor

types.

6.1.1 Motor protection

The pump requires no external motor protection. The

motor incorporates thermal protection against slow

overloading and blocking, TP 211 according to IEC

34-11.

6.1.2 Protection against mains voltage transients

The pump is protected against voltage transients by

built-in varistors between the phases and between

phases and earth.

DANGER

Electric shock

Death or serious personal injury

- If national legislation requires a

Residual Current Device (RCD) or

equivalent in the electrical installation,

this must be type B or better, due to the

nature of the constant DC leakage

current. The RCD must be marked with

the following symbols:

WARNING

Electric shock

Death or serious personal injury

- Carry out the electrical connection in

accordance with local regulations.

WARNING

Electric shock

Death or serious personal injury

- Check that the power plug delivered

with the product is in compliance with

local regulations.

- The protective earth of the power outlet

must be connected to the protective

earth of the product. The plug must

therefore have the same PE connection

system as the power outlet. If not, use a

suitable adapter if allowed by local

regulations.

WARNING

Electric shock

Death or serious personal injury

- A supply disconnecting device made

according to EN 60204-1 5.3.2 must be

provided with means permitting it to be

locked in the OFF (isolated) position.

This device must also be installed in a

position according to EN 60204-1,

5.3.4.

WARNING

Electric shock

Death or serious personal injury

- Power cables without a plug must be

connected to a supply disconnecting

device incorporated in the fixed wiring

according to local regulations.

WARNING

Electric shock

Death or serious personal injury

- Comply with local regulations as to

cable cross-sections.

English (GB)

6.2 Standard functional module, FM 200

6.2.1 Inputs and outputs

The module has these connections:

• two analog inputs

• two digital inputs or one digital input and one

open-collector output

• Grundfos Digital Sensor input and output

• two signal relay outputs

• GENIbus connection.

All inputs and outputs are internally separated from

the mains-conducting parts by reinforced insulation

and galvanically separated from other circuits. All

control terminals are supplied with protective

extra-low voltage (PELV), ensuring protection

against electric shock.

6.2.2 Signal relay 1

LIVE: You can connect supply voltages up to 250

VAC to the output.

PELV: The output is galvanically separated from

other circuits. Therefore, you can connect the supply

voltage or protective extra-low voltage to the output

as desired.

6.2.3 Signal relay 2

PELV: The output is galvanically separated from

other circuits. Therefore, you can connect the supply

voltage or protective extra-low voltage to the output

as desired.

6.2.4 Connection terminals for the mains supply

6.2.5 Connection terminals for inputs and

outputs

Fig. 2 Connection terminals, FM 200

Phases Terminals

Single-phase N, PE, L

Three-phase L1, L2, L3, PE

DANGER

Electric shock

- Death or serious personal injury

- Make sure that the wires to be

connected to the connection groups

below are separated from each other by

reinforced insulation in their entire

lengths.

TM05 3510 3512

AI2

GDS RX

GDS TX

GND

GENIbus A

GENIbus B

+5 V

+24 V

GND

GENIbus Y

GND

+5 V

DI1

AI1

DI3/OC1

+24 V*

+24 V*/5 V*

+24 V*

+5 V*

+24 V*

+24 V*/5 V*

+24 V*

+24 V* OC DI

GND

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Grundfos Pompe à eau

Grundfos

Grundfos TPE 2 Series Manuel d'utilisation

Grundfos

Grundfos DME 60 Manuel utilisateur

Grundfos

Grundfos DP 10 Series Manuel utilisateur

Grundfos

Grundfos NK Series Manuel utilisateur

Grundfos

Grundfos Sololift+ WC-1 Manuel utilisateur

Grundfos

Grundfos ALPHA SOLAR Manuel utilisateur

Grundfos

Grundfos SQ Series Manuel utilisateur

Grundfos

Grundfos CRE-DP Manuel utilisateur

Grundfos

Grundfos CR-H Manuel utilisateur

Grundfos

Grundfos S Manuel utilisateur

Grundfos

Grundfos SE Manuel utilisateur

Grundfos

Grundfos PS.G Series Manuel utilisateur

Grundfos

Grundfos HS Manuel utilisateur

Grundfos

Grundfos LFE Manuel utilisateur

Grundfos

Grundfos CR 1s Manuel utilisateur

Grundfos

Grundfos SP Manuel utilisateur

Grundfos

Grundfos CR SF 32 Mode d'emploi

Grundfos

Grundfos SB Manuel utilisateur

Grundfos

Grundfos KPL Manuel utilisateur

Grundfos

Grundfos CR Manuel utilisateur

Grundfos

Grundfos SL1 Series Manuel utilisateur

Grundfos

Grundfos DWK Manuel utilisateur

Grundfos

Grundfos SR Manuel utilisateur

Grundfos

Grundfos UP15 Manuel utilisateur

Manuels Pompe à eau populaires d'autres marques

Neptun

Neptun NPHW 5500 Manuel utilisateur

Sensidyne

Sensidyne Gilian BDX-II Instructions d'installation et d'utilisation

Draper

Draper 47808 Manuel utilisateur

Trolla

Trolla 12820 Manuel utilisateur

Sunfab

Sunfab SVH Series Manuel utilisateur

WilTec

WilTec 50740 Manuel utilisateur

Fieldmann

Fieldmann FVC 5015 EK Manuel utilisateur

Everbilt

Everbilt EFSUB5-122HD Manuel utilisateur

Graco

Graco Husky 3300e Manuel utilisateur

esotec

esotec 101018 Manuel utilisateur

moyno

moyno 2000 CC Manuel utilisateur

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuel utilisateur

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guide de dépannage

DUROMAX

DUROMAX XP WX Series Manuel utilisateur

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuel utilisateur

Franklin Electric

Franklin Electric IPS Manuel utilisateur

Xylem

Xylem e-1532 Series Manuel utilisateur

Milton Roy

Milton Roy PRIMEROYAL Manuel utilisateur