GROM Audio VLINE Manuel utilisateur
INSTALLATION
MANUAL
www.gromaudio.com
www.gromaudio.com/support.html
NISK
CONTENTS
Package contents......................................................................................................3
CHAPTER 1 —INSTALLATION. ................................................................................3
1.1 Before Installation 3
1.2 Tools 3
1.3 Vehicle Installation 3
1.4Safety Guidelines &Appropriate Use 4
Connect VLine Interface Cable to factory headunit . ...........................................5
Display connections . . .............................................................................................6
Connecting to VLine..................................................................................................6
Routing the GPS Antenna. . . ....................................................................................7
Routing the Microphone. . .......................................................................................8
Mounting the VLine Module. . .................................................................................9
Understanding VLine Ports. ..................................................................................10
Chapter 2 —getting started. . ...............................................................................11
2.1 Initializing
2.2 Functions
SUPPORT. ........................................................................................................13
WARRANTY......................................................................................................13
18 MONTH (18) LIMITED WARRANTY
GRANTOF LICENSE........................................................................................14
OPERATIONAL WARNING AND SAFETY INSTRUCTIONS. ...........................15
3
1.1 Before Installation
Before starting work with any wiring, please wait 90 seconds after turning the
Ignition to the OFF position and disconnecting the negative (-) terminal of the
battery. This is to ensure that no SRS airbags faults are triggered during the
installation when disassembling the vehicles panels and wiring connections
for the VLINE module installation.
Please review the entire manual to familiarize yourself of the VLINE module
and the installation requirements before installing the unit and using it.
1.2 Tools
Have Tools ready for disassembling the dashboard panels to remove the
stereo.
Some basic tools will be required for stereo removal and installation: plastic
prying tools, Phillips head screwdriver,10mm socket and ratchet. Additional
tools may be required depending on vehicle and installation preference.
1.3 Vehicle Installation
Each model vehicle disassembles differently. The removal of the stereo and
CHAPTER 1 — INSTALLATION
PACKAGE CONTENTS
GROM-VLINE SYSTEM
Microphone USB Extension cable
VLine module
GPS Antenna
MCFNISK Interface Cable VNISK Video Cable V-NISKRTH Touch
Screen Assembly
wiring requires special technical skills and experience. If you do not feel
comfortable doing the installation,please consult with your local car audio
shop or installation professional for instructions or assistance,if neces-
sary.
Carefully remove the factory stereo and display out of the dash cavity with
proper tools.
It may be necessary to disconnect items surrounding the stereo and display
to remove them and gain access to the back of the stereo to make your
connections. Make sure to reconnect them back during the reassembly.
1.4 Safety Guidelines & Appropriate Use
By using VLine you agree:
• to operate VLine only when there are safe driving conditions;
• to follow any applicable state and traffic laws;
• to keep an eye on the road at all time while driving;
• do not attempt to play video (such as YouTube) on a display while the
vehicle is in motion;
• do not use VLine without running the engine for the extended period of
time as it can drain the battery.
Do not use Vline in a manner that would distract the driver or that may
otherwise cause injury or death to vehicle occupants or bystanders.
IT IS ILLEGAL IN MOST STATES OF THE UNITED STATES AND MAY BE ILLEGAL
IN OTHER JURISDICTIONS FOR ANY TELEVISION OR OTHER VIDEO DISPLAY,
STREAM, TRANSMISSION OR BROADCAST TO BE VISIBLE TO THE DRIVER
WHILE THE VEHICLE IS IN MOTION. YOU AGREE NOT TO USE ANY VISUAL
COMPONENT OF VLine WHILE IN CONTROL OF A MOVING VEHICLE WHERE
DOING SO WOULD BE ILLEGAL OR DANGEROUS TO VEHICLE OCCUPANTS OR
BYSTANDERS. DOING OTHERWISE CAN LEAD TO SERIOUS INJURY OR DEATH
TO YOU AND OTHERS. PLEASE FIND A SAFE PLACE TO PARK AND ENGAGE
THE PARKING BRAKE BEFORE VIEWING ANY VIDEO DISPLAYS, STREAMS,
TRANSMISSION, OR BROADCAST AVAILABLE THROUGH VLINE.
4
Step 2 - Connect VLine interface cable to factory headunit
Locate the 18-pin and 32-pin connectors behind the stereo headunit and
unplug them. Plug in supplied interface cable (MCFNISK). Reconnect back
what was disconnected from the rear of the stereo into the female plugs of
the supplied MCFNISK interface cable.
Locate the 12-pin port behind the stereo headunit. If there is already
connector plugged in, unplug it and plug MCFNISK 12-pin connector
instead. Leave what was unplugged from the rear of the stereo free and
disconnected. It will not be used.
*Please note that the factory XM/SAT will be disabled and no longer
function. The VLINE will take its place and emulate its functions.
Step 1 - Install stereo touchscreen overlay
Take out the stereo screen and disconnect it from the 24-pin factory connect-
or. Mark this connector for yourself as you will need to replug it back to VLine
video cable.
Take the screen assembly to the comfortable place where you can install the
touchscreen overlay. We recommend using a table. Refer to the manual that
came with your touchscreen overlay package (V-NISKRTH).
6
Step 3 - Connect VLine video cable to factory display
Take stereo display with already installed touchscreen overlay (step 1).
Locate 24-pin port at the rear of the display and plug in the supplied video
cable (VNISK). Reconnect factory 24-pin connector back to VNISK female
plug of the supplied interface cable.
Step 4 - Connecting to VLine
Connect the MCFNISK and VNISK cables to the appropriate ports of VLine
module You will connect V-TOUCH display cable, with TSB1 board attached,
to the connector labeled “TOUCH”on the VAUX cable of GPS antenna
assembly (see next page).
Carefully route all VLine cables (VNISK, MCFNISK, V-TOUCH) to the glove
compartment, where you will connect them to VLine. Be extra carefull with V-
TOUCH cable!
7
Step 5 - Routing the GPS Antenna
The GPS antenna package consists of the antenna connected to VAUX
cable. It also comes with the double-sided tape.
It can be mounted on the top of the dashboard or outside of the vehicle.
We recommend mounting it inside of the vehicle on the passenger side,
on top of the dashboard (see below).Do not leave GPS antenna inside of
the glove compartment, as it can affect the reception of GPS signal.
Plug the VAUX cable into the port labeled CAMERA AV1 on the VLine.
Plug the V-TOUCH cable, with TSB1 board attached, to the connector
labeled “TOUCH”on the VAUX cable with GPS antenna.
Step 6 - Routing the Microphone
Route the microphone to a location where it will be able to pick up voice
clearly. We recommend to mount MIC nearby the rear view mirror but not
directly
on windshield glass. Avoid sticking to ahard surface as it will pick up more
noise.
Plug the microphone into the MIC port of the VLine module
8
9
Step 7 - Mounting the VLine Module
Mount the module in alocation free of any moving parts. We strongly re-
commend mounting the module in an easily accessible location such as the
glove compartment . It will provide easy access to the USB ports of VLine.
Securely mount and install VLine module in a location free from heat,
humidity, moving parts, or direct sunlight. Beware of hot-air flow from your
vehicle’s climate control system. The module should be secured in a suitable
location, free of sharp metal edges, using double-sided tape, Velcro, or wire
ties. The module’s operating temperature range is -30°C to +70°C (-24°F to
+158°F)
10
USB1
iPhone connection
Any other USB device (Keyboard / Mouse)
USB2
USB flash drive
Any USB device (Android, Keyboard / Mouse)
MicroSD
Insert microSD card (*pin side up) to increase storage space for
Vline (up to 128GB supported). The microSD should be formatted
FAT32. File system format exFAT and NTFS are not supported.
HDMI IN
HDMI input connection to connect external video sources.
(add plugin to Dashlinq Launcher to use feature)
HDMI OUT
N/A, not used
MIC
Microphone input, Connect 3.5mm Mono Microphone
Understanding VLine Ports
HDMI IN
HDMI Input MicroSD Card
(Pin side up*)
Pin Side Up
N/A
Not Used
GPS / AV / Camera
Input
WiFi / Bluetooth
Antenna
Microphone
USB2
OTG/USB storage
MIC
CAMERA AV1
HDMI OUT
USB 2
USB 1
USB1
iPhone
Autres manuels pour VLINE
1
Table des matières
Autres manuels GROM Audio Accessoires automobiles
GROM Audio
GROM Audio Vlite Manuel utilisateur
GROM Audio
GROM Audio VOL01 Manuel utilisateur
GROM Audio
GROM Audio GROM-IPOD V2 Adapter Manuel utilisateur
GROM Audio
GROM Audio Wirelinq Manuel utilisateur
GROM Audio
GROM Audio VLine Lite LEX89 Manuel utilisateur
GROM Audio
GROM Audio GROM-SB1 Manuel utilisateur
GROM Audio
GROM Audio GROM-IPD4 Manuel utilisateur
