Grizzly H0590 Manuel utilisateur
Introduction
This 9,000 RPM air sander requires 90 PSI and 6
CFM. Spindle thread nut is 5⁄16" x 24 NF. Weighs 4
lbs. Pad size is 6". Air inlet is 1/4" NPT.
Inventory
A. Air Sander .................................................. 1
B. 6" Sanding Pad .......................................... 1
MODEL H0590
6" DUAL ACTION SANDER
INSTRUCTION SHEET
EYE INJURY HAZARD!
Always wear safety glasses
when using this tool to
prevent serious personal
injury.
INJURY HAZARD!
Always disconnect tool from
air to prevent unexpected
operation during service.
DUST HAZARD!
Always wear respirator when
using this tool.
Figure 2. Installing sanding pad.
Figure 3. Attaching sanding disc.
Figure 1. Model H0590 inventory.
Assembly
To assemble the Model H0590:
1. Thread the sanding pad onto the drive spindle
(Figure 2) and tighten with a 17mm wrench.
A
B
2. Install a 1⁄4" NPT male quick-disconnect fitting
(not included) into the bottom of the sander
handle.
3. Attach a 6" pressure sensitive adhesive (PSA)
sanding disc to the sanding pad as shown in
Figure 3.
COPYRIGHT © MAY, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL8240 PRINTED IN TAIWAN
Maintenance
Lubricate at the beginning of the sanding task.
Place one or two drops of pneumatic tool oil
directly into the air fitting as shown in Figure 5.
Figure 5. Lubricating directly into air fitting.
3. Turn the regulator knob (Figure 4) to adjust
the speed of the sanding disc.
4. Remove pressure on the throttle lever to stop
the sander.
5. When the sandpaper loses its effectiveness,
disconnect the tool, remove sandpaper
from the pad, and replace with a new disc.
If you need help with your new pneumatic tool, call
our Tech Support at: (570) 546-9663.
Figure 4. Sander controls.
Accessories
6" PSA Sanding Discs (3 Pack):
G1445—60 Grit
G4236—80 Grit
G1446—100 Grit
G4237—120 Grit
G1447—150 Grit
G4238—180 Grit
G4239—220 Grit
6" PSA Sanding Discs (Rolls of 100):
G6219—80 Grit
G6220—100 Grit
G6221—120 Grit
G6222—150 Grit
G6223—180 Grit
G6224—220 Grit
H6634—280 Grit
H6635—320 Grit
H6636—400 Grit
H6637—500 Grit
H6638—600 Grit
Throttle
Lever
Regulator
Knob
Operation
To operate the sander:
1. Plug the tool into compressed air.
2. Hold the sander and press the throttle lever
(Figure 4) to operate the sander.
A filter/lubricator/regulator set up is not recom-
mended, as excess oil in the tool could spray onto
the workpiece.
Run the sander for a few minutes to eject excess
oil, then wipe the tool down with a rag and begin
sanding. Oil the tool after use or storage.
H0590 Parts Breakdown and List
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PH0590001 HOUSING 23 PH0590023 ROTOR BLADE
2 PH0590002 AIR INLET 24 PH0590024 O-RING 4.75 X 1.4
3 PH0590003 VALVE SPRING 25 PH0590025 WOODRUFF KEY 2.3 X 12
4 PH0590004 RUBBER GRIP 26 PRP14M ROLL PIN 3 X 6
5 PH0590005 O-RING 8.4 X 1.4 27 PH0590027 ROTOR
6 PH0590006 O-RING 6 X 1.4 28 PH0590028 ROTOR SHAFT
7 PH0590007 VALVE STEM 29 PH0590029 GASKET
8 PH0590008 VALVE BODY 30 PH0590030 DRIVE HOUSING
9 PLN12 LOCK NUT 8-32 31 PSB79M CAP SCREW M5-.8 X 35
10 PH0590010 THROTTLE LEVER 32 PSB33M CAP SCREW M5-.8 X 12
11 PS19 PHLP HD SCR 8-32 X 1-1/2 33 PSB38M CAP SCREW M5-.8 X 25
12 PH0590012 BRACKET 34 PH0590034 ORBITAL HUB
13 PLW03M LOCK WASHER 6MM 35 PFH40M FLAT HD SCR M6-1 X 15
14 PN01M HEX NUT M6-1 36 P6201 BALL BEARING 6201ZZ
15 PH0590015 O-RING 3.4 X 1.4 37 PH0590037 DRIVE SPINDLE
16 PEC17M E-CLIP 14MM 38 PR21M INT RETAINING RING 35MM
17 PH0590017 REGULATOR VALVE 39 PSB48M CAP SCREW M6-1 X 35
18 PH0590018 END PLATE 40 PH0590040 HOUSING COVER
19 PH0590019 CYLINDER 41 PLW03M LOCK WASHER 6MM
20 P6200 BALL BEARING 6200ZZ 42 PH0590042 SPINDLE LOCK
21 PEC08M E-CLIP 16MM 44 PH0590044 O-RING 22.5 X 2.5
22 PN01M HEX NUT M6-1 46 PH0590046 6" PAD
Autres manuels Grizzly Sander
Grizzly
Grizzly G0547 Guide de démarrage rapide
Grizzly
Grizzly G1013 Manuel utilisateur
Grizzly
Grizzly G0563 Manuel utilisateur
Grizzly
Grizzly T32004 Manuel utilisateur
Grizzly
Grizzly G0450 Manuel utilisateur
Grizzly
Grizzly H6192 Manuel utilisateur
Grizzly
Grizzly G0472 Manuel utilisateur
Grizzly
Grizzly T26417 Manuel utilisateur
Grizzly
Grizzly G5049Z Manuel utilisateur
Grizzly
Grizzly H2933 Manuel utilisateur
Grizzly
Grizzly G0702 Manuel utilisateur
Grizzly
Grizzly G1183/G1276 Manuel utilisateur
Grizzly
Grizzly T1239 Manuel utilisateur
Grizzly
Grizzly G0565 Guide de démarrage rapide
Grizzly
Grizzly G0571 Mode d’emploi
Grizzly
Grizzly G1173 Manuel utilisateur
Grizzly
Grizzly G0527 Manuel utilisateur
Grizzly
Grizzly G0458Z Manuel utilisateur
Grizzly
Grizzly G1013 Manuel utilisateur
Grizzly
Grizzly G1014Z Manuel technique
