Grizzly G5344 Manuel utilisateur
Introduction
This 15,000 RPM air sander requires 75 PSI and
3" x 41/2" sanding sheets. (You can cut a standard
9" x 11" sanding sheet into sixths and trim each
piece to size.) Air hose inlet is 1/4" NPT.
Inventory
A. Air Palm Sander ......................................... 1
B. Air Hose ...................................................... 1
MODEL G5344
AIR PALM SANDER
INSTRUCTION SHEET
Figure 2. Opening clamp.
Figure 1. Model G5344.
COPYRIGHT © MAY, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL8253 PRINTED IN TAIWAN
Assembly and Attaching Abrasives
To assemble the sander and attach sandpa-
per:
1. Thread the air hose into the sander.
2. Install a 1⁄4" NPT male quick-disconnect fitting
(not included) into the end of the hose.
3. Lift one clamp up over the bracket (Figure 2),
then pull the clamp down to open it.
4. Insert one end of the sandpaper between the
clamp and base as shown in Figure 3, and
lift the clamp up and back over the bracket to
secure the sandpaper.
Figure 3. Attaching and securing sanding sheet.
Bracket
A
B
EYE INJURY HAZARD!
Always wear safety glasses
when using this tool to
prevent serious personal
injury.
INJURY HAZARD!
Always disconnect tool from
air to prevent unexpected
operation during service.
DUST HAZARD!
Always wear respirator when
using this tool.
5. Repeat Step 3 with the opposite clamp, fold
the sandpaper over the sander, and repeat
Step 4, making sure the paper fits snugly as
shown in Figure 4.
Figure 4. Attaching sandpaper on opposite side.
Operation
To operate the sander:
1. Connect the tool to compressed air.
2. Hold the sander and push the throttle valve
(Figure 5) inwards to turn the sander on.
Figure 6. Lubricating directly into air fitting.
Maintenance
Lubricate at the beginning of the sanding task.
Place one or two drops of pneumatic tool oil
directly into the air fitting as shown in Figure 6.
Figure 5. Sander controls.
Throttle
Valve
3. Push or pull the throttle valve (Figure 5)
between ON and OFF to control the speed of
the sander.
A filter/lubricator/regulator set up is not recom-
mended, as excess oil in the tool could spray onto
the workpiece.
Run the sander for a few minutes to eject excess
oil, then wipe the tool down with a rag and begin
sanding. Oil the tool after use or storage.
If you need help with your new pneumatic tool, call
our Tech Support at: (570) 546-9663.
4. Pull the throttle valve outwards to stop the
sander.
5. When the sandpaper loses its effectiveness,
disconnect the sander from air, remove
sandpaper from the clamps, and replace with
a new sheet.
G5344 Parts Breakdown and List
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PS07M PHLP HD SCR M4-.7 X 8 14 P5344014 CYLINDER
2 PLW02M LOCK WASHER 4MM 15 P5344015 STEEL BALL
3 P5344003 HOUSING COVER 16 P5344016 CLAMP SPRING
4 P5344004 RUBBER SUPPORT ASSEMBLY 17 P5344017 FLAT HEAD SCREW
5 P5344005 TUBE ASSEMBLY 18 P5344018 CYLINDER SUB ASSEMBLY
6 P5344006 MODEL LABEL 19 PFH49M FLAT HD SCR M3-.5 X 6
7 P5344007 RUBBER PAD ASSEMBLY 20 P5344020 VALVE BUSHING
8 P5344008 THROTTLE VALVE 21 P5344021 FLAT HEAD SCREW
9 P5344009 O-RING 22 PLW02M LOCK WASHER 4MM
10 P5344010 VALVE FITTING 23 P5344023 HOSE SUB ASSEMBLY
11 P5344011 HOUSING CAP 24 P5344024 CLAMP STOMPER
12 PS38M PHLP HD SCR M4-.7 X 10 25 P5344025 ROLL PIN
13 P5344013 END PLATE
Autres manuels Grizzly Sander
Grizzly
Grizzly G0529 Manuel utilisateur
Grizzly
Grizzly G0716 Manuel utilisateur
Grizzly
Grizzly G0446 Manuel utilisateur
Grizzly
Grizzly H0596 Guide de démarrage rapide
Grizzly
Grizzly G1095 Manuel utilisateur
Grizzly
Grizzly G0563 Mode d’emploi
Grizzly
Grizzly G0563 Manuel utilisateur
Grizzly
Grizzly G9922 Manuel utilisateur
Grizzly
Grizzly G1015 Manuel utilisateur
Grizzly
Grizzly G1014ZX Mode d’emploi
Grizzly
Grizzly G0565 Guide de démarrage rapide
Grizzly
Grizzly G0458 Manuel utilisateur
Grizzly
Grizzly G0574 Manuel utilisateur
Grizzly
Grizzly G0449 Guide de démarrage rapide
Grizzly
Grizzly G9922 Manuel utilisateur
Grizzly
Grizzly G0723 Manuel utilisateur
Grizzly
Grizzly G0719 Manuel utilisateur
Grizzly
Grizzly G0787 Manuel utilisateur
Grizzly
Grizzly G1071 Manuel utilisateur
Grizzly
Grizzly Line Boring Machine G0642 Manuel utilisateur
