GREENS Zeon Manuel utilisateur
ZEON / ZEON NOIR SINK MIXERS
INSTALLATION INSTRUCTIONS
#41656 12/17
ATTENTION PLUMBER
To ensure the optimum performance and customer satisfaction please adhere to the following:
Flush out all pipe work prior to installation
Installation shall be in accordance with the AS/NZS3500 series of standards.
The maximum operating pressure within any building should not exceed 500kpa.
Pressure above 500kpa can cause damage from water hammer, reducing life of appliances,
taps and fittings and cause excessive noise in the plumbing system.
Pressure over 500kPa will require a limiting valve.
Inline filters must be installed on both hot and cold supplies.
TECHNICAL DATA
Minimum Water pressure for satisfactory operation: 150kPa
Maximum Water pressure: 500kPa
Maximum hot water temperature: 70ºC
If the Water temperature exceeds 70ºC an approved Tempering Valve must be fitted.
The flow rate of the sink and basin mixers has been rated under the Australian Water
Efficiency Labeling Scheme (WELS).
Please leave this form with the product once installed.
For full warranty terms and conditions, please see the warranty card enclosed with this product
or visit www.greenstapware.com/warranty-and-care/
Distributed by: Greens Global (Australia) Ltd
10/101 Wedgewood Rd, Hallam, Victoria 3803
Phone: 1800 244 487 Fax: 1800 244 212
Email: [email protected]
Website: www.greenstapware.com
Service Hotline: 1800 244 992
BATCH #
PRODUCT #
STD Sink Mixer
Gooseneck Sink Mixer
All Zeon Sink
Note: Fits Maximum Bench thickness of 38mm.
To install mixer, cut a mounting hole 35mm in diameter in the bench surface.
1. Unscrew mounting nut and remove steel washer and rubber washer from
threaded mixer tail. Ensure seal is sitting in groove at base of mixer.
2. Position mixer in bench top with hot inlet pipe on the left.
3. From underneath the bench install the rubber washer then the steel washer
and screw mounting nut onto threaded tail of mixer and tighten the jacking
screws.
a. Screws may require backing off before installing nut.
4. Install inlet hoses:
. a. Screw the “HOT” hose (red) and hand tighten into hot inlet (red) of mixer.
b. Screw the “COLD” hose (blue) and hand tighten, into cold inlet of mixer.
5. Connect flexi hoses to water supply.
a. The union nuts must be connected to 15mm thread fittings which have a
machined end face with a chamfer, not “sawn off” threaded tube.
b. Do not over tighten the nuts.
i. Hand tighten then 1/4 turn with spanner.
c. Do not kink, stretch or twist , any bends in the flexible hose should have
radius of no less than 85mm.
6. Turn on water supply and check for leaks.
INSTALLATION INSTRUCTIONS
SINK MIXER
BENCH TOPS
Formica/wooden bench tops, extra mounting support is required below the bench.
Stainless steel bench tops ensure the mounting washer is against the S/Steel.
Vitreous china tops additional sealant maybe required at the base of the mixer
to ensure a water tight seal.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels GREENS Équipements de cuisine et de salle de bain
Manuels Équipements de cuisine et de salle de bain populaires d'autres marques
Alpha Bidet
Alpha Bidet Alpha One Manuel utilisateur
InSinkErator
InSinkErator H/HC3300 Manuel d'installation
Clou
Clou Xo type 1 Manuel utilisateur
Kohler
Kohler Contra 26448T-4 Manuel utilisateur
Grohe
Grohe Bridgeford 20 158 Manuel utilisateur
Hans Grohe
Hans Grohe Croma Select S 180 Showerpipe EcoSmart... Manuel utilisateur