Greenlee PairMapper Manuel utilisateur
999 5220.3 © 2004 Greenlee Textron Inc. 6/04
PairMapper™
INSTRUCTION MANUAL
Read and understand all of the instructions and safety information
in this manual before operating or servicing this tool.
2
Description
The Greenlee PairMapper™ is a simple-to-use testing device that enables network
professionals to quickly and easily verify the integrity of twisted pair cables by identifying
various wiring faults. In one step, the PairMapper tests twisted pair cables for open pairs,
shorted pairs, reversed pairs, crossed pairs, and split pairs. Specially designed remote
terminators allow for one-person testing of multiple installed cables. The Tone function sends
a signal along installed cable that can be traced with any inductive amplifier (probe).
Package contents: PairMapper unit, four remote terminators, shielded patch cable,
instruction manual, and carrying case.
Safety
Safety is essential in the use and maintenance of Greenlee tools and equipment. This
instruction manual and any markings on the tool provide information for avoiding hazards
and unsafe practices related to the use of this tool. Observe all of the safety information
provided.
Purpose of This Manual
This instruction manual is intended to familiarize all personnel with the safe operation and
maintenance procedures for the Greenlee PairMapper. Keep this manual available to all
personnel. Replacement manuals are available upon request at no charge.
All specifications are nominal and may change as design improvements occur. Greenlee Textron
Inc. shall not be liable for damages resulting from misapplication or misuse of its products.
PairMapper is a trademark of Greenlee Textron Inc.
PairMapper™
3
Important Safety Information
This symbol is used to call your attention to hazards or unsafe practices which could
result in an injury or property damage. The signal word, defined below, indicates the
severity of the hazard. The message after the signal word provides information for
preventing or avoiding the hazard.
SAFETY ALERT SYMBOL
Immediate hazards which, if not avoided, WILL result in severe injury or death.
Hazards which, if not avoided, COULD result in severe injury or death.
Hazards or unsafe practices which, if not avoided, MAY result in injury or property
damage.
KEEP THIS MANUAL
4
Important Safety Information
Read and understand this material before operating or servicing this
equipment. Failure to understand how to safely operate this tool
could result in an accident causing serious injury or death.
Electric shock hazard:
Contact with live circuits could result in severe injury or death.
Electric shock hazard:
•Using this unit in a high frequency activated area may result in unstable or inaccurate
readings.
•Do not drop or get the unit wet as it may cause internal damage.
•Do not attempt to repair this unit. It contains no user-serviceable parts.
•Do not expose the unit to extremes in temperature or humidity.
Refer to “Specifications.”
•Use this unit for the manufacturer’s intended purpose only, as described in this
manual. Any other use can impair the protection provided by the unit.
Failure to observe these precautions may result in injury and can damage the unit.
PairMapper™
5
Identification
1. Main jack (RJ45)
2. Wiremap/Tone/Off
switch
3. Shield indicator
4. Fault (ID) LEDs
5. Low battery LED
6. Battery compartment
door (on back)
7. Terminator storage
8. Test button
9. Tone indicator
10. Pair indicators
11. Remote jack (RJ45)
1
2
3
5
6
4
8
9
10
11
Remote
Terminators
Main Unit
7
6
Features
•Testing for wiring faults of open, shorted, reversed, crossed, and split pairs
• Split pair fault detection at a minimum 0.4 m (16") cable length
•Testing of twisted pair cables to over 200 m (656 ft)
•Tone generator for tracing installed cables and locating faults
•One-person identification of up to four remote terminators
•Verification of shield integrity
•Easy-to-read fault display and high speed testing
•“Debug mode” for detailed fault identification results
• “Auto sleep mode” and power off switch to decrease power consumption
Operation
Testing a Cable
1. Slide the switch to Cable.
2. Plug one end of the cable into the RJ45 jack on the main unit and the other end into the
RJ45 jack on any remote terminator.
3. Press the TEST button and check the results:
•First, check the five horizontally aligned green LEDs (1-2, 3-6, 4-5, 7-8, and SHIELD):
Solid light: Good pair
Flashing light: Faulted pair
No light: Open pair
•Simultaneously, check the first four vertically aligned LED indicators (SHORT,
REVERSED, MISWIRE, and SPLIT PAIRS) to identify any existing wiring faults.
•For more detailed information about what faults are occurring in which pairs, hold the
TEST button for 2 seconds to activate “debug mode.” The tester will test each pair one
by one, pausing briefly on each pair, and display the corresponding fault status.
PairMapper™
7
Sending Tone
1. Slide the switch to Tone.
2. The PairMapper offers two tone modes—Continuous and Warble.
• For Continuous mode, press and release the TEST button.
•For Warble mode, press and hold the TEST button for approximately 2 seconds.
•To change modes, switch the tester off and restart.
3. Use any probe or inductive amplifier to trace the signal to the subject wire.
Remote Identification
1. Slide the switch to Cable.
2. Plug one end of the cable into the RJ45 jack on the main unit and the other end into the
RJ45 jack on the remote terminator.
3. Press the TEST button. One of the ID LEDs will flash three times. This indicates the
number of the remote identification unit attached to the far end of the subject cable. The
tester then automatically continues with the same cable test procedure as step 3 under
“Testing a Cable.”
Operation (cont’d)
8
Fault Status
Shorted Pair
3
63
6
Open Pair
1
21
2
1
21
2
Reversed Pair
PairMapper™
9
Fault Status (cont’d)
1
2
3
6
1
2
3
6
Crossed Pairs
1
2
4
5
3
6
7
8
1
2
4
5
3
6
7
8
Split Pairs
10
Specifications
Connectors: Shielded RJ45 jacks
Cable Types: Shielded or unshielded twisted pair
Cable Length:
Minimum: 0.4 m (16")
Maximum: Over 200 m (656 ft)
LED Indicators:
Cable Pairs: 4 green LEDs
Shield Continuity: 1 green LED
Fault/Remote ID: 4 red LEDs
Tone Mode: 1 red LED
Low Battery: 1 red LED
Power:
Main Unit: 4 x Alkaline 1.5 V AAA batteries
Remote Terminators: No battery required
Dimensions: 125 mm x 52 mm x 30 mm (4.9" x 2.0" x 1.2")
Environment:
Operating: 0 °C to 50 °C (32 °F to 122 °F)
Storage: -20 °C to 60 °C (14 °F to 140 °F)
Humidity: 10% to 90%, non-condensing
Table des matières
Langues :
Autres manuels Greenlee Testeur de circuit
Greenlee
Greenlee GT-10 Manuel utilisateur
Greenlee
Greenlee GT-10GFI Manuel utilisateur
Greenlee
Greenlee 5708 Manuel utilisateur
Greenlee
Greenlee 5715 Manuel utilisateur
Greenlee
Greenlee SVC-10 Manuel utilisateur
Greenlee
Greenlee GT-55e Manuel utilisateur
Greenlee
Greenlee AFI-100 Manuel utilisateur
Greenlee
Greenlee 1110 Manuel utilisateur
Greenlee
Greenlee GT-65 Manuel utilisateur
Greenlee
Greenlee PG1 Manuel utilisateur
Manuels Testeur de circuit populaires d'autres marques
IDEAL
IDEAL 61-534 Manuel utilisateur
Kusam-meco
Kusam-meco KM 1812EL Manuel utilisateur
MGE UPS Systems
MGE UPS Systems Galaxy 5000 Manuel utilisateur
YOKOGAWA
YOKOGAWA MY10 Manuel utilisateur
Power Probe Tek
Power Probe Tek PRO SERIES THE MAESTRO Manuel utilisateur
Gossen MetraWatt
Gossen MetraWatt DUSPOL expert 1000 Manuel utilisateur
