h.
The RO Water system will see the most maintenance as filters need to be
replaced annually. Mount the system on a wall where clear access is
accessible.
i.
If a High Limit Stat is included, it
of the DTA.
j. The Air
Flow Switch should be mounted on the supply side (positive pressure)
INSTALLATION:
I) Generator and DTA Location and Piping:
A. Locate
the Generator and DTA within 1
each other.
B. When
using the STS system the same rule applies.
installed LEVEL! VERY IMPORTANT!
C.
When installing the DTA make sure it is level or pitching back slightly toward
the supply pipe. Fasten all holes on the DTA flange to the bottom of th
D.
Make sure there are no obstructions
downstream of the DTA for at least 3
E.
Sealant can be used on the flange if desired for complete seal.
F.
Once you have located the Generator in a clear
hose cuffs and begin installing pipe between the Generator and the DTA.
Follow the project plans for piping size but verify that they adhere to the
-
3000 Series should utilize 4”ID or greater supply pip
-
-
1000 Series should utilize
CAUTION:
When piping try to avoid creating
the piping. If you cannot avoid doing so then
from such trap locations.
3/8”id pipe/tubing and there should be at least a 3” long nipple of ½” size off
the trap pointed
down to create enough “head” to drain the line.
Pip
e the drain line to an appropriate drain location. Again be sure not to trap
water. If necessary employ a condensate pump/drain to elevate the drain water
and evacuate it during drain cycles.
G.
Determine whether the system you are installing is a
system (please note that the
designates what type of application, supply side or return side, your system
is. If any questions call the Factory Representative).
H.
If the system is a supply si
feed from a take off up stream of the DTA location (consult your Submittal
drawings for more specific information).
The RO Water system will see the most maintenance as filters need to be
replaced annually. Mount the system on a wall where clear access is
If a High Limit Stat is included, it
should be located at least
Flow Switch should be mounted on the supply side (positive pressure)
.
I) Generator and DTA Location and Piping:
the Generator and DTA within 1
0
’ ft of equivalent piping distance from
using the STS system the same rule applies.
Make sure the STS tank is
installed LEVEL! VERY IMPORTANT!
When installing the DTA make sure it is level or pitching back slightly toward
the supply pipe. Fasten all holes on the DTA flange to the bottom of th
Make sure there are no obstructions
, bends, or branches
downstream of the DTA for at least 3
’ft in either direction.
Sealant can be used on the flange if desired for complete seal.
Once you have located the Generator in a clear
and accessible location use the
hose cuffs and begin installing pipe between the Generator and the DTA.
Follow the project plans for piping size but verify that they adhere to the
3000 Series should utilize 4”ID or greater supply pip
ing.
utilize 4”ID or greater supply piping
1000 Series should utilize
3”ID or greater supply piping
When piping try to avoid creating
water “traps” or low points in
the piping. If you cannot avoid doing so then
be
from such trap locations.
(see Fig. 1 )
Drain line size must be a minimum of
3/8”id pipe/tubing and there should be at least a 3” long nipple of ½” size off
down to create enough “head” to drain the line.
e the drain line to an appropriate drain location. Again be sure not to trap
water. If necessary employ a condensate pump/drain to elevate the drain water
and evacuate it during drain cycles.
Determine whether the system you are installing is a
system (please note that the
humidifier schedule column
designates what type of application, supply side or return side, your system
is. If any questions call the Factory Representative).
If the system is a supply si
de installation then you must pipe in a supply air
feed from a take off up stream of the DTA location (consult your Submittal
drawings for more specific information).
3
The RO Water system will see the most maintenance as filters need to be
replaced annually. Mount the system on a wall where clear access is
’ ft. downstream
Flow Switch should be mounted on the supply side (positive pressure)
’ ft of equivalent piping distance from
Make sure the STS tank is
When installing the DTA make sure it is level or pitching back slightly toward
the supply pipe. Fasten all holes on the DTA flange to the bottom of th
e duct.
Sealant can be used on the flange if desired for complete seal.
and accessible location use the
hose cuffs and begin installing pipe between the Generator and the DTA.
Follow the project plans for piping size but verify that they adhere to the
.
water “traps” or low points in
-drain
Drain line size must be a minimum of
3/8”id pipe/tubing and there should be at least a 3” long nipple of ½” size off
down to create enough “head” to drain the line.
e the drain line to an appropriate drain location. Again be sure not to trap
water. If necessary employ a condensate pump/drain to elevate the drain water
designates what type of application, supply side or return side, your system
de installation then you must pipe in a supply air
feed from a take off up stream of the DTA location (consult your Submittal
