Great Stage Light GLM015 Manuel utilisateur
90W SPOT MOVING HEAD
USER MANUAL
1
TABLE OF CONTENTS
1．BEFORE YOU BEGIN
WHAT IS INCLUDED
UNPACKING NSTRUCTIONS
MANUAL CONVENTIONS
ICONS
SAFETY INSTRUCTIONS
2．INSTRODUCTION
TECHNICAL SPECIFICATION
PRODUCT DIMENSIONS
PRODUCT OVERVIEW
3．SETUP
AC POWER
POWER LINKING
SIGNAL LINKING（DMX）
FUSE REPLACEMENT
MOUNTING ORIENTATION RIGGING
4. OPERATING INSTRUCTIONS
CONFIGURING THE STARTING ADDRESS
CONTROL PANEL FUNCTIONS
MENU MAP
DMX CHANNEL VALUES
5. APPENDIX
DMX PRIMER
GENERAL MAINTENANCE
FIXTURE LINKING
DATA CABLING
DMX DATA CABLE
CABLE CONNECTORS
3-PIN TO 5-PIN CONVERSION CHART
SETTING UP A DMX SERIAL DATA LINK
SETTING THE STARTING ADDRESS
GENERAL TROUBLESHOOTING
2
1. BEFORE YOU BEGIN
What is included
1 x Spot
1 x Mounting bracket and screws
1 x Power cable
1 x User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the
contents to ensure that all parts are present, and have been received in good
condition. Notify the shipper immediately and retain packing material for
inspection if any parts appear damaged from shipping or the carton itself
shows signs of mishandling. Save the carton and all packing materials. In the
event that a fixture must be returned to the factory, it is important that the
fixture be returned in the original factory box and packing.
Manual Conventions
manuals use the following conventions to differentiate certain types of
information from the regular text.
Icons
This manual uses the following icons to indicate information that requires
special attention on the part of the user.
CONVENTION
MEANING
[10]
A LCD display to be configured
<Menu>
A key to be pressed on the fixture’s control panel
1~512
A range of values
50/60
A set of values of which only one can be chosen
Settings
A menu option not to be modified (for example,
showing the operating mode/current status)
MENU >Settings
A sequence of menu options to be followed
ON
A value to be entered or selected
3
Safety Instructions
● Please keep this User Manual for future consultation. If you sell the unit
to another user, be sure that they also receive this instruction booklet.
● Always make sure that you are connecting to the proper voltage, and that
the line voltage you are connecting to is not higher than that stated on the
decal or rear panel of the fixture.
● This product is intended for indoor use only! To prevent risk of fire or
shock, do not expose fixture to rain or moisture.
● Make sure there are no flammable materials close to the unit while
operating.
● The unit must be installed in a location with adequate ventilation, at least
20 in (50 cm) from adjacent surfaces. Be sure that no ventilation slots are
blocked.
● Always disconnect from power source before servicing or replacing fuse
and be sure to replace with same fuse source.
● Secure fixture to fastening device using a safety chain.
● Maximum ambient temperature (Ta) is 104° F (40° C). Do not operate
fixture at temperatures higher than this.
● In the event of a serious operating problem, stop using the unit
immediately.
Never try to repair the unit by yourself. Repairs carried out by unskilled
people can lead to damage or malfunction. Please contact the nearest
ICONS
MEANING
This paragraph contains critical installation, configuration or
operation information. Failure to comply with this
information may render the fixture partially or completely
inoperative, cause damage to the fixture or cause harm to
the user.
This paragraph contains important installation or
configuration information. Failure to comply with this
information may prevent the fixture from functioning
correctly.
This paragraph reminds you of useful, although not critical,
information
4
authorized technical assistance center.
● Never connect the device to a dimmer pack.
● Make sure the power cord is never crimped or damaged.
● Never disconnect the power cord by pulling or tugging on the cord.
● Never carry the fixture directly from the cord. Always use the
hanging/mounting bracket.
● Avoid direct eye exposure to the light source while it is on.
● Never carry the fixture by holding the head. Always use the carrying
handle.
2. INTRODUCTION
Technical Specification
1) Voltage: 100-240V,50-60Hz
2) Power consumption: 110W
3) LED: ultra bright 90W LED
4) LED color wheel: Basic 7 colors+ white, can adjust speed rainbow effect
5) Fixed gobo: 8 gobos+ white, Gobo rotating CW and CCW from slow to
fast), gobo shaking
6) Rotation gobo: 6 gobos + white, can bidirectional speed change
rotation, gobo shaking
7) Dimmer/Strobe: Dimmer, 1-20t/s
8) Focus: Electronic Focus
9) Pan::540° Tilt: 270
10) Control: DMX 512, 14/16 /11CHs
11) Working mode: Stand-alone mode, Controller mode, Master/Slave
synchronization mode
12) Other function: Pan/Tilt speed adjustable
Housing: High temperature resistant engineering plastic + aluminum
alloy.
13) Weight: 6.5KG
14) Product Size: 240*240*370mm
15) Packing Size: 350*340*375mm
5
Product Dimensions
6
Product Overview
7
3. SET UP
AC Power
This fixture runs on 100-240VAC, 50/60 Hz. This fixture used switch power
supply, it can transform by itself when user input power.
Always connect the fixture to a switched circuit. Never connect
the fixture to a rheostat (variable resistor) or dimmer circuit, even if the
rheostat or dimmer channel is used only as a 0 to 100% switch.
Always connect the fixture to a circuit with a suitable electrical
ground.
The maximum quantity of fixtures that may be linked is 4.
Power Linking
This fixture contains power linking via the outlet located in front of the power
input cable. Please see the diagram below for further explanation.
8
Signal Linking (DMX)
The diagrams below illustrate the signal (DMX) linking for this fixture. This is
used both in DMX mode and when operating the fixtures in Master/Slave
mode. Please see the diagram below for further explanation.
Fuse Replacement
9
With a flat head screwdriver unscrew the fuse holder out of its housing,
turning counter-clockwise. Remove the damaged fuse from its holder and
replace with exact same type fuse. Insert the fuse holder back in its place and
reconnect power.
Mounting
Orientation
The Spot may be mounted in any safe position provided there is adequate
room for ventilation.
Rigging
Be sure that the structure can support 10 times the weight of the fixture.
Please see the “Technical Specifications” section of this manual for a detailed
weight listing. Mount the fixture securely. Two hanging clamps for truss
mounting may be used, or nuts and bolts for permanent installation may be
used. The holes in each bracket are 13 mm in size. When rigging, consider
routine maintenance and control panel access. Please see the following steps
for installation.
●If the power link out is intended to be used with multiple fixture, take into
account the length of each power cable, and mount the fixtures close
enough to one another to accommodate for this.
●Attach both included bolts in the locations indicated below, using a metric
8 mm Allen wrench.
●Attached 2 hanging clamps to the bracket in each of the two locations
indicated below
●Safety cables must always be used.
Table des matières
Autres manuels Great Stage Light Matériel de DJ
Manuels Matériel de DJ populaires d'autres marques
thomann
thomann Stairville DJ Lase 40-G MK-III Manuel utilisateur
Eagletone
Eagletone 6 Eyes Flower Manuel utilisateur
EuroLite
EuroLite FLD-1508 Manuel utilisateur
Technical Pro
Technical Pro LG8xSEA Manuel utilisateur
JB Systems
JB Systems Lounge Laser DMX Manuel utilisateur
Lightmaxx
Lightmaxx Vega Halo 90 Manuel utilisateur
Elation
Elation FUZE WASH Z350 Manuel utilisateur
Maverick
Maverick MK3 WASH Manuel utilisateur
Infinity
Infinity TF-260C7 Fresnel Manuel utilisateur
Chauvet
Chauvet EVE E-50Z Manuel utilisateur
Eliminator Lighting
Eliminator Lighting E 138 Manuel utilisateur
EuroLite
EuroLite Mini Multicolor LED Flashing Light SC Manuel utilisateur