Grandinroad 61336 Manuel utilisateur
7.5ft MONARCH FIR TREE
(61336)
ASSEMBLY INSTRUCTIONS
(3 SECTIONS WITH 2 EXTENSION CORDS)
PLEASE READ INSTRUCTIONS BEFORE ASSEMBLYING YOUR TREE
Your 7.5’ Monarch Fir Tree should contain the following: 1 Tree stand Replacement bulbs and fuses
If any piece is missing please contact a Grandinroad 2 Eyelet screws 3 Tree sections labeled A, B, C
Product Specialist
HOW TO ASSEMBLE AND SHAPE YOUR TREE:
1. BEFORE STARTING TO ASSEMBLE YOUR TREE, CHOOSE A LOCATION NEAR AN 110V
ELECTRICAL WALL OUTLET FOR THE PRELIT TREE.
2. REMOVE THE TREE SECTIONS FROM THE CARTON. SECTION A IS THE BOTTOM,
SECTION B IS THE MIDDLE AND SECTION C IS THE TOP OF THE TREE.
3. PLACE THE TREE STAND ON A LEVEL SURFACE. INSTALL THE BOTTOM END OF THE
LOWER “SECTION A”INTO THE STAND. HOLD THE SECTION IN A LEVEL POSITION AND
TIGHTEN THE EYELET SCREWS IN THE STAND AGAINST THE TREE TRUNK SURFACE.
MAKE SURE THE SCREWS ARE TIGHTENED AS EVENLY AS POSSIBLE MAINTAINING A
SNUG AND SECURE POSITION. (FIG 1~2)
FIGURE 1 FIGURE 2
4. INSERT THE MIDDLE (“SECTION B”) INTO THE BOTTOM (“SECTION A”) TREE POLE.
FINISH BY INSERTING THE TOP (“SECTION C”) INTO THE MIDDLE (“SECTION B”) TREE
POLE. (FIG 3~4)
FIGURE 3 FIGURE 4
(RECEPTACLE HUB MARKER)
5. LOCATE THE PLUG FROM SECTION C AND PLUG INTO THE RECEPTACLE HUB
LOCATED IN SECTION A. THE HUB WILL HAVE A YELLOW CARD ATTACHED FOR EASY
IDENTIFICATION. ***DO NOT REMOVE THE ELECTRICAL TAPE FROM THE HUB***
(SECTION C PLUG)
6. SHAPE THE BRANCHES, STARTING AT THE BOTTOM WITH THE TIPS FARTHEST FROM
THE POLE AND CURVING OUT FROM THE POLE. ONE TO THE RIGHT, ONE TO THE LEFT
AND ONE AT THE CENTER. TO ACHIEVE A REALISTIC LOOK, EACH BRANCH SHOULD
BE SHAPED.
8. SHIFT ANY BRANCHES AS NECESSARY TO FILL ANY GAPS AND SLIGHTLY UPSWEEP
ALL BRANCHES FOR A UNIFORM LOOK.
9. PLUG THE TWO REMAINING EXTENTSION CORDS CORD INTO A GROUNDED
ELECTRICAL OUTLET OR POWER STRIP.
(SECTION A EXTENSION CORD) (SECTION B EXTENSION CORD)
7.5ft MONARCH TREE
STORAGE
GENTLY PRESS BRANCHES AGAINST THE TREE TRUNK AS YOU DISMANTLE THE TREE
REMOVE THE TREE STAND FROM SECTION A
CAREFULLY PLACE THE TREE SECTIONS AND TREE STAND BACK INTO THE CARTON(S) AND
TAPE THEM CLOSED
CAUTIONS AND WARNINGS
oDO NOT LIFT SECTIONS OF THE TREE WITH THE BRANCHES. LIFT USING THE METAL POLE.
oDO NOT STEP ON THE BRANCHES DURING THE ASSEMBLY PROCESS
oDO NOT TWIST THE BULBS WHEN REPLACING AND ONLY USE THE SPARE BULBS
PROVIDED IN THE CARTON AS REPLACEMENTS. PULL THE LAMP AND PLASTIC BASE
STRAIGHT OUT OF THE LAMPHOLDER.
oDO GRASP ELECTRICAL PLUGS AND REMOVE IT FROM THE RECEPTACLE OR OUTLET
DEVICE. NEVER UNPLUG BY PULLING ON THE CORD.
oPLEASE DO NOT REMOVE TAPE FROM PLUG HUBS; THIS IS FOR YOUR PROTECTION AND
TO INSURE THAT THE PLUGS MAINTAIN A FIRM CONNECTION.
oDO NOT HANG ORNAMENTS OR OTHER OBJECTS FROM THE ELECTRICAL CORDS OR
WIRES.
oTHIS PRODUCT EMPLOYS ELECTRICAL OVERLOAD PROTECTION (FUSES) INSIDE EACH
PLUG. SPARE FUSES ARE PROVIDED IN THE CARTON. OUR PRODUCT DESIGN HAS NOT
EXPERIENCED FUSE PROBLEMS; HOWEVER, IF A FUSE BLOWS THE PRODUCT SHOULD BE
UNPLUGGED BEFORE REPLACING ANY FUSE.
oWHEN A LIGHT SET FLICKERS OR GOES ON AND OFF, THE MOST COMMON PROBLEM IS A
LOOSE FITTING BULB. CHECK TO MAKE SURE ALL BULBS ARE SEATED FIRMLY IN THE
SOCKETS.
oTHE MOST COMMON PROBLEM WITH A LIGHT SET IS A BULB THAT NEEDS REPLACING.
LOOSE OR DAMAGED BULBS CAN CAUSE AN ENTIRE STRING TO FAIL. A BURNED OUT
BULB WILL NOT CAUSE THE STRING TO GO OUT IF IT IS NOT REMOVED.
CARE AND MAINTENANCE
STORE CARTON IN COOL AND DRY PLACE.
DO NOT STORE THE TREE IN A DAMP AREA OR IN AN AREA WHERE THE TEMPERATURE
EXCEEDS 100˚ F.
9ft MONARCH FIR TREE
(61338)
ASSEMBLY INSTRUCTIONS
(4 SECTIONS WITH 3 EXTENSION CORDS)
PLEASE READ INSTRUCTIONS BEFORE ASSEMBLYING YOUR TREE
Your 9’ Monarch Fir Tree should contain the following: 1 Tree stand Replacement bulbs and fuses
If any piece is missing please contact a Grandinroad 3 Eyelet screws 4 Tree sections labeled A, B, C, D
Product Specialist
HOW TO ASSEMBLE AND SHAPE YOUR TREE:
1. BEFORE STARTING TO ASSEMBLE YOUR TREE, CHOOSE A LOCATION NEAR AN 110V
ELECTRICAL WALL OUTLET FOR THE PRELIT TREE.
2. REMOVE THE TREE SECTIONS FROM THE CARTON. SECTION A IS THE BOTTOM,
SECTION B IS THE LOWER MIDDLE, SECTION C IS THE UPPER MIDDLE AND SECTION D
IS THE TOP OF THE TREE.
3. PLACE THE TREE STAND ON A LEVEL SURFACE. INSTALL THE BOTTOM END OF THE
LOWER “SECTION A”INTO THE STAND. HOLD THE SECTION IN A LEVEL POSITION AND
TIGHTEN THE EYLET SCREWS IN THE STAND AGAINST THE TREE TRUNK SURFACE.
MAKE SURE THE SCREW ARE TIGHTENED AS EVENLY AS POSSIBLE MAINTAINING A
SNUG AND SECURE POSITION. (FIG 1~2)
FIGURE 1 FIGURE 2
4. INSERT THE LOWER MIDDLE (“SECTION B”) INTO THE BOTTOM (“SECTION A”) TREE
POLE. FOLLOW BY INSERTING UPPER MIDDLE (“SECTION C”) INTO THE LOWER MIDDLE
(“SECTION B”). FINISH BY INSERTING THE TOP (“SECTION D”) INTO THE MIDDLE
(“SECTION C”) TREE POLE. (FIG 3~5)
FIGURE 3 FIGURE 4 FIGURE 5
(RECEPTACLE HUB MARKER)
5. LOCATE THE PLUG FROM SECTION D AND PLUG INTO THE RECEPTACLE HUB
LOCATED IN SECTION A. THE HUB WILL HAVE A YELLOW CARD ATTACHED FOR EASY
IDENTIFICATION. ***DO NOT REMOVE THE ELECTRICAL TAPE FROM THE HUB***
(SECTION D PLUG)
6. SHAPE THE BRANCHES, STARTING AT THE BOTTOM WITH THE TIPS FARTHEST FROM
THE POLE AND CURVING OUT FROM THE POLE. ONE TO THE RIGHT, ONE TO THE LEFT
AND ONE AT THE CENTER. TO ACHIEVE A REALISTIC LOOK, EACH BRANCH SHOULD
BE SHAPED.
7. SHIFT ANY BRANCHES AS NECESSARY TO FILL ANY GAPS AND SLIGHTLY UPSWEEP
ALL BRANCHES FOR A UNIFORM LOOK.
8. PLUG THE THREE REMAINING EXTENTSION CORDS CORD INTO A GROUNDED POWER
STRIP.
(SECTION A EXT. CORD) (SECTION B EXT. CORD) (SECTION C EXT. CORD)
9ft MONARCH TREE
STORAGE
GENTLY PRESS BRANCHES AGAINST THE TREE TRUNK AS YOU DISMANTLE THE TREE
REMOVE THE TREE STAND FROM SECTION A
CAREFULLY PLACE THE TREE SECTIONS AND TREE STAND BACK INTO THE CARTON(S) AND
TAPE THEM CLOSED
CAUTIONS AND WARNINGS
oDO NOT LIFT SECTIONS OF THE TREE WITH THE BRANCHES. LIFT USING THE METAL POLE.
oDO NOT STEP ON THE BRANCHES DURING THE ASSEMBLY PROCESS
oDO NOT TWIST THE BULBS WHEN REPLACING AND ONLY USE THE SPARE BULBS
PROVIDED IN THE CARTON AS REPLACEMENTS. PULL THE LAMP AND PLASTIC BASE
STRAIGHT OUT OF THE LAMPHOLDER.
oDO GRASP ELECTRICAL PLUGS AND REMOVE IT FROM THE RECEPTACLE OR OUTLET
DEVICE. NEVER UNPLUG BY PULLING ON THE CORD.
oPLEASE DO NOT REMOVE TAPE FROM PLUG HUBS; THIS IS FOR YOUR PROTECTION AND
TO INSURE THAT THE PLUGS MAINTAIN A FIRM CONNECTION.
oDO NOT HANG ORNAMENTS OR OTHER OBJECTS FROM THE ELECTRICAL CORDS OR
WIRES.
oTHIS PRODUCT EMPLOYS ELECTRICAL OVERLOAD PROTECTION (FUSES) INSIDE EACH
PLUG. SPARE FUSES ARE PROVIDED IN THE CARTON. OUR PRODUCT DESIGN HAS NOT
EXPERIENCED FUSE PROBLEMS; HOWEVER, IF A FUSE BLOWS THE PRODUCT SHOULD BE
UNPLUGGED BEFORE REPLACING ANY FUSE.
oWHEN A LIGHT SET FLICKERS OR GOES ON AND OFF, THE MOST COMMON PROBLEM IS A
LOOSE FITTING BULB. CHECK TO MAKE SURE ALL BULBS ARE SEATED FIRMLY IN THE
SOCKETS.
oTHE MOST COMMON PROBLEM WITH A LIGHT SET IS A BULB THAT NEEDS REPLACING.
LOOSE OR DAMAGED BULBS CAN CAUSE AN ENTIRE STRING TO FAIL. A BURNED OUT
BULB WILL NOT CAUSE THE STRING TO GO OUT IF IT IS NOT REMOVED.
CARE AND MAINTENANCE
STORE CARTON IN COOL AND DRY PLACE.
DO NOT STORE THE TREE IN A DAMP AREA OR IN AN AREA WHERE THE TEMPERATURE
EXCEEDS 100˚ F.
12ft MONARCH FIR TREE
(61340A & 61340B)
ASSEMBLY INSTRUCTIONS
(5 SECTIONS WITH 4 EXTENSION CORDS)
PLEASE READ INSTRUCTIONS BEFORE ASSEMBLYING YOUR TREE
Your 12’ Monarch Fir Tree should contain the following: 1 Tree stand Replacement bulbs and fuses
If any piece is missing please contact a Grandinroad 3 Eyelet screws 5 Tree sections labeled A, B, C, D, E
Product Specialist
HOW TO ASSEMBLE AND SHAPE YOUR TREE:
1. BEFORE STARTING TO ASSEMBLE YOUR TREE, CHOOSE A LOCATION NEAR AN 110V
ELECTRICAL WALL OUTLET FOR THE PRELIT TREE.
2. REMOVE THE FIVE TREE SECTIONS FROM BOTH CARTONS. SECTION A IS THE
BOTTOM, SECTION B IS THE LOWER MIDDLE, SECTION C IS THE MIDDLE, SECTION D IS
THE UPPER MIDDLE AND SECTION E IS THE TOP OF THE TREE.
3. PLACE THE TREE STAND ON A LEVEL SURFACE. INSTALL THE BOTTOM END OF
“SECTION A”INTO THE STAND. HOLD THE SECTION IN A LEVEL POSITION AND
TIGHTEN THE EYLET SCREWS IN THE STAND AGAINST THE TREE TRUNK SURFACE.
MAKE SURE THE SCREW ARE TIGHTENED AS EVENLY AS POSSIBLE MAINTAINING A
SNUG AND SECURE POSITION. (FIG 1~2)
FIGURE 1 FIGURE 2
4. INSERT THE LOWER MIDDLE (“SECTION B”) INTO THE BOTTOM (“SECTION A”) TREE
POLE. FOLLOW BY INSERTING THE MIDDLE (“SECTION C”) INTO THE LOWER MIDDLE
(“SECTION B”). INSERT THE UPPER MIDDLE (“SECTION D”) INTO THE MIDDLE (“SECTION
C”) TREE POLE. FINISH BY INSERTING THE TOP (“SECTION E”) INTO THE MIDDLE
(“SECTION D”) TREE POLE. (AS ILLUSTRATED BELOW)
(RECEPTACLE HUB MARKER)
5. LOCATE THE DOUBLE PIGGY-BACKED PLUG FROM SECTION E AND PLUG INTO THE
RECEPTACLE HUB LOCATED IN SECTION B. THE HUB WILL HAVE A YELLOW CARD
ATTACHED FOR EASY IDENTIFICATION. ***DO NOT REMOVE THE ELECTRICAL
TAPE FROM THE HUB***
(SECTION E PLUG)
Autres manuels Grandinroad sapin artificiel
Manuels sapin artificiel populaires d'autres marques
Trim a Home
Trim a Home TY-S6-250L Manuel utilisateur
Polygroup
Polygroup TG7600NVQC03 Manuel utilisateur
Sears
Sears Donner & Blitzen M44814 Manuel utilisateur
BETHLEHEM LIGHTING
BETHLEHEM LIGHTING 6.5’ Tinsel Tree Manuel utilisateur
Home Accents Holiday
Home Accents Holiday TG76P3D93L08 Manuel utilisateur
Polygroup
Polygroup TG76M3S45C02 Manuel utilisateur
Polygroup
Polygroup TG90P3693L00 Manuel utilisateur
Costway
Costway CM23595US Manuel utilisateur
Polygroup
Polygroup TV46M3ADVC05 Manuel utilisateur
Home Accents Holiday
Home Accents Holiday TG76P4C15D03 Manuel utilisateur
Polygroup
Polygroup TV46P7001X00 Manuel utilisateur
Holiday Living
Holiday Living TV40EH339C01 Manuel utilisateur
