Graco G3 Series Manuel utilisateur
Instructions
G3 Reservoir and O-Ring
Replacement Kit
Instructions for replacing G3 reservoir and o-rings. For professional use only.
Part No.:
571179 - 2 Liter, Oil
571042, 571069 - 2 Liter, Grease
571182 - 4 Liter, Oil
571183 - 4 Liter, Grease
25C764 - 4 Liter, Mid-Section
Important Safety Instructions
Read all warnings and instructions in this
manual and the G3 Pump Instruction manual
included with your unit. Save these instruc-
tions.
3A0534H
EN
Instructions
23A0534H
Instructions
Pressure Relief
Relieve pressure in system by using two wrenches
working in opposite directions on pump element and
pump element fitting to only loosen fitting.
NOTE: When loosening pump element fitting, do NOT
loosen pump element. Loosening pump element will
change the output volume.
Disassembly
Reference numbers used in these instructions corre-
spond to parts included in Kit and are provided on page
1. Parts identified with an alpha character are user pro-
vided or already installed components.
Reservoir Disassembly
1. Disconnect power source.
2. Relieve pressure using Pressure Relief Procedure
provided.
3. Use a strap wrench around reservoir to turn reser-
voir 1/4 turn counter-clockwise (FIG. 2).
4. Remove reservoir from G3 base and discard reser-
voir according to local codes for proper disposal.
For 25C764 replacement only: Do not discard res-
ervoir. Only discard broken mid section.
NOTE: If your unit includes a follower plate, remove any
parts noted in Step 1 of the Follower Plate Disassembly
section and keep those parts for reassembly.
Follower Plate Disassembly
If your unit does not have a follower plate, continue
disassembly with O-Ring Disassembly instructions,
page 3.
1. Verify the following parts were removed with reser-
voir (FIG. 3):
• Spring (S)
• Follower Pate (FP)
• Follower Plate Seal (FPS)
• Rod (R)
SKIN INJECTION HAZARD
High-pressure fluid from dispense device, hose leaks, or
ruptured components will pierce skin. This may look like
just a cut, but it is a serious injury that can result in ampu-
tation. Get immediate surgical treatment.
Follow Pressure Relief Procedure in this manual, when
you stop dispensing and before cleaning, checking, or
servicing equipment.
FIG. 1
FIG. 2
FIG. 3
R
S
FP FPS
Instructions
3A0534H 3
2. Remove any parts still installed in the G3 base.
3. Be sure parts remaining in reservoir were removed
to reuse them for reassembly.
4. Examine follower plate seal referenced in Step 1 for
wear or damage. If it is damaged, it must be
replaced. Part No. 278139 is available from Graco.
Contact customer service to order this part or your
local Graco distributor.
Upper O-Ring Disassembly
If o-ring (a) did not come out of the groove in ricer plate
(b) when reservoir was removed, remove and discard
o-ring according to local codes for proper disposal (FIG.
4).
The lower o-ring is located beneath the ricer plate
(b). If replacing this o-ring, continue with Lower
O-Ring Disassembly instructions.
If lower o-ring is not replaced, begin Reassembly
instructions starting on page 4.
Lower O-Ring Disassembly Instructions
1. Perform all applicable previous disassembly instruc-
tions for reservoir, follower plate (if applicable) and
upper o-ring.
2. Turn paddle (c) clockwise to loosen and remove it
from G3 base (FIG. 5).
NOTE: For models that include a Low Level paddle
and/or follower plate only, be careful when removing
stirring paddle from G3 that bearing (f) does not fall
into the unit.
3. Remove ricer plate (b) from G3 base.
4. Remove o-ring (e) located under ricer plate (FIG. 6).
FIG. 4
a
b
FIG. 5
FIG. 6
c
d
f
b
e
Instructions
43A0534H
Reassembly
Lower O-Ring Installation
1. Coat new o-ring (1) with grease (user supplied) and
install o-ring in bottom groove of ricer plate (b).
2. Replace ricer plate (b), aligning circular sections
with the round bosses in the base.
NOTE: It may be necessary to use a press to seat
the plate properly in the G3 base.
3. Reinstall paddle (c) by turning it counter-clockwise
till tight - hand tighten only (FIG. 8).
NOTE: If a low level paddle (d) is installed, to pre-
vent damage, hold low level paddle in its full out
position while installing stirring paddle (FIG. 9).
4. Complete installation following instructions for Top
O-ring and Reservoir installation, page 4.
Top O-ring Installation
1. Coat new o-ring (1) with grease (user supplied).
2. Install o-ring in groove of ricer plate (b) (FIG. 10).
Follower Plate Installation
If your unit does not have a follower plate, continue
installation instructions with Top O-Ring Installa-
tion, page 5.
1. Verify low level paddle (d) is in full out position as
shown in FIG. 9.
2. Install follower plate (FP) on stirring paddle (c). Be
sure the seal (FPS) is facing down (toward ricer
FIG. 7
FIG. 8
b
1
c
FIG. 9
FIG. 10
d
b
1
Instructions
3A0534H 5
plate) as shown in FIG. 11.
3. Install spring (S) into spring pocket (f).
4. Install Rod (R) into reservoir (2).
5. Slide rod (R) through center of spring (S) and fol-
lower plate (FP).
6. Seat spring in spring pocket in top of reservoir.
7. Compress spring to install reservoir. See Reservoir
Installation instructions.
Reservoir Installation
1. Install new reservoir (2) with vent (g) facing toward
the rear left (h) of the G3 base. See FIG. 12 for cor-
rect orientation of these parts to ensure proper
installation.
2. Position strap wrench over reservoir and use it to
turn reservoir 1/4 turn clockwise till reservoir will not
turn any farther (FIG. 12).
FIG. 11
c
FP
S
R
FPS
f
FIG. 12
NOTICE
Be careful when installing reservoir that o-ring is not
pinched. If the o-ring is not correctly installed,
grease could leak out of the bottom of the G3 reser-
voir.
2
g
h
Parts
63A0534H
Parts
2 Liter, Oil Model 571179 2 Liter, Grease Model 571042
Ref. Description Qty
1 RESERVOIR 1
2 CAP, oil, fill 1
3 LABEL 1
4O-RING 1
5PACKING 1
2
1
3
4
5
Ref. Description Qty
1 RESERVOIR 1
3 LABEL 1
4O-RING 1
5 O-RING, square 1
1
3
4
5
Parts
3A0534H 7
4 Liter, Oil Model 571182 4 Liter, Grease Model 571183
4 Liter, Mid Section 25C764
Ref. Description Qty
1 RESERVOIR 1
2 CAP, oil, fill 1
3 LABEL 1
4O-RING 1
6 ADAPTER 1
2
1
3
4
6
Ref. Description Qty
1 RESERVOIR 1
3 LABEL 1
4O-RING 1
6 ADAPTER 1
Ref. Description Qty
7 MID SECTION 1
8O-RING 1
1
3
4
5
7
8
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
For patent information, see www.graco.com/patents
Original instructions. This manual contains English. MM 3A0534
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440-1441
Copyright 2010, Graco Inc. is registered to ISO 9001
www.graco.com
Revised February 2017
Autres manuels pour G3 Series
7
Table des matières
Autres manuels Graco Pompe à eau
Graco
Graco HIGH-FLO 220-575 Manuel d'utilisation
Graco
Graco G3-G-24NC-8LTA00-0D00L000 Manuel utilisateur
Graco
Graco Husky 1050A Mode d’emploi
Graco
Graco 218746 Manuel d'utilisation
Graco
Graco TRITON 3D150 Manuel d'utilisation
Graco
Graco Bulldog 221-104 Manuel d'utilisation
Graco
Graco Hydra-Clean 1040 Mode d’emploi
Graco
Graco ChemSafe 515 Manuel de la liste des pièces
Graco
Graco Hydra-Clean 1040 Manuel d'utilisation
Graco
Graco VRM Manuel utilisateur
Graco
Graco 24V672 Manuel d'utilisation et d'entretien
Graco
Graco Hydra-Clean 1040 Manuel
Graco
Graco 207321 Manuel d'utilisation
Graco
Graco Dura-Flo 7847 Manuel utilisateur
Graco
Graco 24F531 Manuel utilisateur
Graco
Graco Series A Manuel d'utilisation
Graco
Graco GTP10 Series Manuel utilisateur
Graco
Graco Check-Mate P05LCS Manuel de la liste des pièces
Graco
Graco Fire-Ball 425 E Series Manuel d'utilisation
Graco
Graco M 60 Manuel d'utilisation
