Graco 563918 Manuel utilisateur
3A2603D
EN
Repair
MVB Pump Piston
and Seal Repair Kit
Used to repair pistons and seals used in MVB pumps. For professional use only.
Model No.:
563918 - MVB Pump 1/4 Piston Kit
8000 psi (55.2 MPa, 552 bar) Maximum Working
Pressure
563919 - MVB Pump 3/8 Piston Kit
3000 psi (20.7 MPa, 207 bar) Maximum Working
Pressure
563920 - MVB Pump Seal Kit
Important Safety Instructions
Read all warnings and instructions in this manual
and in your MVB Pump instruction manual included
with your unit. Save all instructions.
Installation
2 3A2603D
Installation
Pressure Relief Procedure
1. Disconnect power source.
2. Loosen outlet fitting or alternate outlet. (FIG. 1)
Disassembly
Reference numbers used in the following instructions
refer to Parts, page 4.
1. Relieve pressure and remove pump from MVB
box.
2. Place pump upside down in a soft-jaw vise.
3. Depress piston guide (6) and remove self locking
ring (8e) and piston guide (6), ring retainer (8c), lock
washer (8g), piston retainer spring (1) and retention
spring (4) from the pump cylinder.
4. Remove pump from vise and turn it over. Replace
pump in soft-jaw vise with adjustment nut facing
upward.
5. Loosen set screw (8j) to relieve locking force on
cylinder and piston assembly. Removing the set
screw entirely is not necessary.
6. Remove pipe plug (8h). Unthread and remove
cylinder assembly (5).
NOTE:
• Care should be taken when removing cylinder
assembly. Do not cut or damage o-rings
(7b - 7e).
• Hold (a) (FIG. 2) with a 13/16 wrench when
removing pipe plug.
7. Inspect o-rings and backup rings (7b-7h) as
necessary. Replace damaged o-rings and
backup rings.
8. Remove pump cylinder from vise.
9. Place valve assembly (5) in vise and remove
indicator port adapter (a) (FIG. 2).
10. Remove valve assembly (5) from vise and remove
spring (3) and check ball (8a) from pump cylinder.
11. Inspect components and replace as needed.
SKIN INJECTION HAZARD
This equipment stays pressurized until pressure is
manually relieved. To help prevent serious injury such
as skin injection from pressurized fluid, follow the
Pressure Relief Procedure when you stop dispensing
and before cleaning, checking, or servicing the
equipment.
FIG. 1
FIG. 2
Installation
3A2603D 3
Reassembly
Reference numbers used in the following instructions
refer to Parts, page 4.
NOTE: Lubricate all o-rings and retaining rings (7 and 8)
with grease prior to installation
1. Reassemble o-rings, retaining rings (7) and
indicator port adapter (a) on piston valve assembly
(5). Refer to parts illustration provided on 4 for
proper orientation when reassembling these parts.
2. Place pump cylinder in soft-jaw vise right side up.
Install check ball (8a) and spring (3) in pump.
3. Install piston valve assembly (5) in pump cylinder.
4. Install pipe plug (8h).
NOTE:
• Hold (a) (FIG. 2) with a 13/16 wrench when
installing pipe plug.
5. Remove pump cylinder from vise and turn it over.
Replace pump in soft-jaw vise.
6. Install retention spring (4), spring retainer (1), ring
retainer, piston guide (6) and self locking ring (8e)
through bottom of pump cylinder.
7. Press on the piston guide (6) to assure free
movement of the piston.
8. Reinstall the pump on the MVB Gearbox.
9. Remove the pipe plug (8h) from the top of the
indicator adapter.
10. Bleed the pump of all air by cycling the pump until
oil flows from the port.
11. Re-install the plug (8h).
12. Set the adjustment to the desired output (page 4).
13. Tighten the cylinder retaining screw.
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
Original instructions. This manual contains English. MM 3A2603
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2016 Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revision D, February 2022
Parts
FIG. 3
Ref Part Description Qty
1 556495 RETAINER, spring
(kits 563918, 563920)
1
556496 RETAINER, spring
(kits 563919, 563920)
1
2 556726 GASKET, pump 1
3 556960 SPRING, piston 1
4 557012 SPRING, piston 1
5 563115 VALVE, piston, 1/4 cylinder
(kit 563918)
1
563119 VALVE, piston, 3/8 cylinder
(kit 563919)
1
6 560469 GUIDE, piston (kit 563918, 563919) 1
7 558015 KIT, MVB Pump Seal 1
7a BALL, 0.188 diameter 1
7b O-RING, backup, -015 flurocarbon 1
7c O-RING, backup, -017 flurocarbon 1
7d O-RING, -019 flurocarabon 1
7e O-RING, -012 flurocarbon 1
7f RING, backup, -19, PTFE 2
7g RING, backup, -17, PTFE 2
7h RING, backup, -015 PTFE 2
8 558016 KIT, MVB Pump Hardware 1
8a BALL, chrome, .500 1
8b TAG, direction (not shown) 1
8c❊RING, retainer, -25 E-ring 1
8f RING, retainer, 1-1/2 1
8e★RING, retainer, 3/8
8g WASHER, lock, 3/8 2
8h PLUG, 1/8 nptf 1
8j PLUG, pipe, 1/4 nptf 2
8k SCREW, HHCS 1/4 x 0.37 1
❊1/4 in. piston size only
★3/8 in. piston size only
Ce manuel convient aux modèles suivants
2
Autres manuels Graco Pompe à eau
Graco
Graco 235706 Manuel d'utilisation
Graco
Graco G-Mini Series Manuel utilisateur
Graco
Graco SaniForce 24V310 Manuel de la liste des pièces
Graco
Graco GlasCraft Guardian A Series Manuel d'utilisation et d'entretien
Graco
Graco Series A Manuel utilisateur
Graco
Graco Husky 1050e Mode d’emploi
Graco
Graco LubeMaster Manuel utilisateur
Graco
Graco LD Series Manuel utilisateur
Graco
Graco ChemSafe 1590 Manuel de la liste des pièces
Graco
Graco Hydra-Clean 1040 Manuel utilisateur
Graco
Graco Xtreme 116MCN Manuel d'utilisation
Graco
Graco Mini Fire-Ball 225 Manuel d'utilisation
Graco
Graco Series A Manuel de la liste des pièces
Graco
Graco Foam-Cat Series Manuel d'utilisation
Graco
Graco 257100 Mode d’emploi
Graco
Graco Husky D71 Series Manuel d'utilisation
Graco
Graco Premier 970199 Manuel d'utilisation
Graco
Graco 287834 Mode d’emploi
Graco
Graco C Series Manuel utilisateur
Graco
Graco Husky Sanitary Series Manuel d'utilisation
