Graco 288466 Manuel utilisateur

Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441

311845C

Instructions

Displacement Pump

- For portable spray application of architectural paints and coatings -

Model 288466, 288467, 288468, 288819

3300 psi (22.8 MPa, 25 bar) Maximum Working Pressure

Important Safety Instructions

Read all warnings and instructions in this manual.

Save these instructions.

Ti8844a

Model 288467/288468

Model 288466

Model 288819

Warnings

2311845C

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-

tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back

to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where

applicable.

WARNING

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system

component. See Technical Data in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all

equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information

about your material, request MSDS forms from distributor or retailer.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manu-

facturer’s replacement parts only.

• Do not alter or modify equipment.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

MOVING PARTS HAZARD

Moving parts can pinch or amputate fingers and other body parts.

• Keep clear of moving parts.

• Do not operate equipment with protective guards or covers removed.

• Pressurized equipment can start without warning. Before checking, moving, or servicing equipment,

follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.

Service

311845C 3

Service

Pressure Relief Procedure

1. Engage trigger lock.

2. Turn engine ON/OFF switch to OFF.

3. Move pump switch to OFF and turn pressure control

knob fully clockwise.

4. Unlock trigger lock. Hold metal part of gun firmly to

side of grounded metal pail and trigger gun to

relieve pressure.

5. Engage the trigger lock.

6. Open all fluid drain valves in the system, having a

waste container ready to catch drainage. Leave

drain valve(s) open until you are ready to spray

again.

If you suspect the spray tip or hose is clogged or that

pressure has not been fully relieved after following the

steps above, VERY SLOWLY loosen tip guard retaining

nut or hose end coupling to relieve pressure gradually,

then loosen completely. Clear hose or tip obstruction.

Tools Needed

•Vise

• 12-inch adjustable, open-end wrench (2)

• Hammer, 20 oz. maximum

• Small screwdriver

• Throat Seal Liquid

• Pick or long small screwdriver

Cleaning and Inspecting Parts

• Clean and inspect all parts. Replace worn or dam-

aged parts.

• Remove and clean the sleeve when you are repack-

ing the pump.

The system pressure must be manually relieved to pre-

vent the system from starting or spraying accidentally.

To reduce the risk of an injury from accidental spray

from the gun, splashing fluid, or moving parts, follow

the Pressure Relief Procedure whenever you,

• are instructed to relieve the pressure

• stop spraying

• check or service any of the system equipment

• install or clean the spray nozzle.

Never use a sharp or pointed tool to remove sleeve

or other components which could result in pump rup-

ture and cause serious bodily injury. If the sleeve

cannot be removed easily, return the sleeve and cyl-

inder to an authorized Graco distributor for removal.

Component What to look for

Ball seats in intake valve

and piston

nicks or wear

Inside sleeve worn or scratched

Piston rod worn or scratched

Repair

4311845C

Repair

See your sprayer instruction manual for complete

instructions for removing and installing the pump in your

sprayer.

Disassembly

1. (Fig. 1) Remove packing nut (3).

FIG. 1

2. (Fig. 2) Unscrew intake valve from cylinder.

FIG. 2

3. (Fig. 3) Disassemble intake valve. Clean and

inspect o-ring (17). You may need to use a pick to

remove o-ring.

FIG. 3

4. (Fig. 4) Use a hammer to tap piston rod (5) out of

cylinder (2), or flip pump over and tap piston rod out

against work bench.

FIG. 4

5. (Fig. 5) Remove piston rod (5) from sleeve (4).

FIG. 5

ti8845a

ti8846a

Spring (26) for model 288819 is optional and is not

included with the pump.

ti8847b

(288467/288468)

(288819)

ti8848a

ti8849a

Repair

311845C 5

6. (Fig. 6) Unscrew piston valve (6) from piston rod (5).

Clean and inspect parts. The piston has a special

thread locking/sealing patch. Do not remove the

patch. The patch allows for disassembly/assembly

procedures before it is necessary to apply Loctite®

to the threads.

FIG. 6

7. (Fig. 7) Remove packing and glands from piston

rod. Note orientation for installation.

FIG. 7

8. (Fig. 8) Remove throat packings and glands from

cylinder. Discard throat packings and glands.

FIG. 8

Do not clean or wipe piston valve (6) threads. Clean-

ing the piston valve threads could destroy the special

sealing patch and cause the piston valve to come

loose during operation.

ti8850a

ti8851a

ti8853a

Repair

6311845C

Reassembly

Note: For steps 1-4 refer to Fig. 9.

1. Stack male gland (7) on piston rod (5).

2. Alternately stack blue UHMWPE (8) and brown

UHMWPH (9) (288466, 288467, 2884680) or

leather (288819) packings on piston rod.

Note orientation.

3. Install female gland (10).

4. Install backup washer (13) and piston wiper (12) on

piston valve (6). Note orientation.

The special sealing patch on piston valve threads is

good for 4 repackings. Use Loctite®on piston valve

threads after 4 repackings.

FIG. 9

5. (Fig 10) Install ball (11) in piston rod (5). If Loctite®

is applied to piston valve threads, ensure that none

gets on ball.

FIG. 10

6. (Fig. 11) Install piston valve (6) to piston rod (5).

Torque to 55 +/- 3 ft-lb (74.57 +/- 4 N• m).

FIG. 11

ti8854a

ti8855a

ti8856a

Repair

311845C 7

7. Soak all leather packings in SAE 30W oil for 1 hour

minimum prior to assembly.

Note: For steps 8-10 refer to Fig. 12.

8. Place male gland (20) in cylinder.

9. Alternately stack UHMWPE (21) and leather pack-

ings (22). Note orientation.

10. Place female gland (23) in top of cylinder. Seat

packings.

FIG. 12

11. (Fig. 13) Install packing nut (3) into cylinder and

hand tighten.

FIG. 13

12. (Fig. 14) Install o-rings (14) inside cylinder (2) and

on sleeve (4). Slide sleeve (4) into bottom of cylinder

(2). Replace o-ring (15) if desired.

FIG. 14

Note: O-ring (15) is not required for safe pump opera-

tion.

13. (Fig. 15) Grease top inch or two of piston rod (5)

that goes through the sleeve/cylinder assembly

throat packings. Grease piston packings at bottom

of piston pump.

Carefully slide piston assembly (5) into bottom of

sleeve/cylinder assembly (2) until pump rod pro-

trudes out the top and piston packings are totally

inside the sleeve (4).

FIG. 15

CAUTION

Never slide piston assembly (5) into top of sleeve (4)

as this may damage piston packings.

21 22

ti8857a

288467/

288468

288466

288819

ti8858a

Place inside cylinder (2)

and push to shoulder

with sleeve (4).

ti8859a

ti8860a

Repair

8311845C

14. (Fig. 16) Reassembly intake valve with new o-ring

(17), seat (16) and ball (19). Seat may be flipped

over and used on the other side. Clean seat thor-

oughly.

FIG. 16

15. (Fig. 17) Install intake valve on cylinder. Torque to:

200 +/- 5 ft-lb (271 +/- 7 N•m) 288467/288468, 288819.

110+/- 5 ft-lb (149 +/- 7 N•m) 288466.

FIG. 17

16. Torque packing nut to:

140 +/- 10 in-lb (15 +/- 1 N•m)

288467/288468, 288819

125 +/- 10 in-lb (14 +/- 1 N•m)

288466

When pump packings begin to leak, tighten packing

nut down until leakage stops or lessens. This allows

approximately 100 gallons of additional operation

before repacking is required.

Spring (26) for model 288819 is optional and is not

included with the pump.

ti8847b

(288467/ 288468)

(288819)

Parts

311845C 9

Parts

Model 288467/288468

*Included in Repair Kit 287813

† Included in Repair Kit 240918

ti8826a

Ref Part Description Qty

1 15E655 HOUSING 1

2 288482 CYLINDER (model 288467) 1

288483 CYLINDER (model 288468)

3 15J792 NUT, packing 1

4 249121 SLEEVE, cylinder (model 288467) 1

287817 SLEEVE, cylinder (model 288468)

5 288469 ROD, piston (model 288467) 1

288470 ROD, piston (model 288468)

6 249177 VALVE, piston 1

7* 189585 GLAND, packing, male 1

8* PACKING,VEE (blue) 8

9* PACKING,VEE (brown) 3

10* 189588 GLAND, packing, female 1

11* 107203 BALL, valve, check 1

12* 119636 WIPER, piston 1

13* 15J800 WASHER, back up 1

14* 108822 PACKING, o-ring 2

15* 107306 PACKING, o-ring 1

16† 240918 SEAT, carbide 1

17†* 107098 PACKING, o-ring 1

18 198505 GUIDE, ball 1

19†* 107167 BALL,SST 1

20* 15G658 GLAND, male 1

21* PACKING,VEE (leather) 3

23* 15G657 GLAND, female 1

24* 112590 PLUG, throat, seal 1

25* 108832 PACKING, o-ring 1

26* 245256 SPRING, intake ball 1

Parts

10 311845C

Model 288466

*Included in Repair Kit 288471

†Included in Repair Kit 244199

ti8825a

Ref Part Description Qty

1 195894 HOUSING, intake 1

2 288727 CYLINDER 1

3 193032 NUT, packing 1

4 248210 SLEEVE, cylinder 1

5 288479 ROD, piston 1

6 240150 VALVE, piston 1

7* 183178 GLAND, packing, male 2

8* PACKING (blue) 8

9* PACKING,VEE (brown) 3

10* 183185 GLAND, packing, female 2

11* 101947 BALL, bearing 1

12* 118504 WIPER, piston 1

13* 15C998 WASHER, backup 1

14* 107098 PACKING, o-ring 2

15* 106556 PACKING, o-ring 1

16† 244199 SEAT, carbide 1

17† 108526 PACKING, o-ring 1

18 193027 GUIDE, ball 1

19†* 102972 BALL 1

22* PACKING,VEE (leather) 3

24* 183171 PLUG 1

25* 120818 PACKING, o-ring 1

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Graco Pompe à eau

Graco

Graco Check-Mate 2100 A Series Manuel d'utilisation

Graco

Graco 287834 Manuel utilisateur

Graco

Graco 244195 Mode d'emploi

Graco

Graco HYDRA-SPRAY President A Series Manuel d'utilisation

Graco

Graco 234019 Manuel d'utilisation

Graco

Graco Monark A Series Manuel d'utilisation

Graco

Graco ProMix PD2K Manuel utilisateur

Graco

Graco Monark Stubby 248321 Manuel utilisateur

Graco

Graco High-Flo Manuel d'utilisation

Graco

Graco 237282 Manuel d'utilisation

Graco

Graco Husky 2200 Mode d’emploi

Graco

Graco saniforce 2150 Manuel

Graco

Graco ChemSafe 515 Series Manuel de la liste des pièces

Graco

Graco MP-25 Mode d’emploi

Graco

Graco RoadLazer A Series Manuel d'utilisation

Graco

Graco Series A Manuel utilisateur

Graco

Graco SaniForce 1040e Manuel d'utilisation et d'entretien

Graco

Graco 216-256 Manuel d'utilisation

Graco

Graco QUANTM QTC Series Manuel utilisateur

Graco

Graco 19D873 Manuel utilisateur

Graco

Graco Series A Manuel utilisateur

Graco

Graco HYDRA-SPRAY 218-058 A Manuel d'utilisation

Graco

Graco Hydra-Clean 1040 Manuel d'utilisation et d'entretien

Graco

Graco 24V671 Manuel utilisateur

Manuels Pompe à eau populaires d'autres marques

Neptun

Neptun NPHW 5500 Manuel utilisateur

Sensidyne

Sensidyne Gilian BDX-II Instructions d'installation et d'utilisation

Draper

Draper 47808 Manuel utilisateur

Trolla

Trolla 12820 Manuel utilisateur

Sunfab

Sunfab SVH Series Manuel utilisateur

WilTec

WilTec 50740 Manuel utilisateur

Fieldmann

Fieldmann FVC 5015 EK Manuel utilisateur

Everbilt

Everbilt EFSUB5-122HD Manuel utilisateur

esotec

esotec 101018 Manuel utilisateur

moyno

moyno 2000 CC Manuel utilisateur

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuel utilisateur

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guide de dépannage

DUROMAX

DUROMAX XP WX Series Manuel utilisateur

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuel utilisateur

Franklin Electric

Franklin Electric IPS Manuel utilisateur

Xylem

Xylem e-1532 Series Manuel utilisateur

Milton Roy

Milton Roy PRIMEROYAL Manuel utilisateur

STA-RITE

STA-RITE ST33APP Manuel utilisateur