Graco Fluid Defender 25V475 Manuel utilisateur

3A7279B

Instructions

Fluid Defender™

Level Sensor

For monitoring lubrication fluid tank levels in above ground, stationary tanks. Not for use

with tanks containing gasoline or any other Class I NFPA 30 flammable fluids. Not for use

with tanks without required overfill containment protection, not a replacement for overfill

containment protection. For professional use only.

Not approved for use in explosive atmospheres or hazardous (classified) locations.

Models:

25V475 - Sensor, Single, High Level, 3 ft

25V476 - Sensor, Single, Low Level, 10 ft

25V577 - Sensor, Single, Low Level, 30 ft

25V478 - Sensor, Dual Level, 10 ft

25V479 - Sensor, Dual Level, 30 ft

Related Manuals

Important Safety Instructions

Read all warnings and instructions in this

manual before using the equipment.

Save these instructions.

Manual in

English Description

130641 Pulse® Fluid Management, Register Your

Devices quick guide

3A9335 Fluid Defender

3A7280 Air Control Solenoid Valve for Fluid

Defender

Warnings

2 3A7279B

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The

exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks.

When these symbols appear in the body of this manual or on warning labels, refer back to these Warnings.

Product-specific hazard symbols and warnings not covered in this section may appear throughout the body of this

manual where applicable.

WARNING

FIRE AND EXPLOSION HAZARD

When flammable fluids are present in the work area, such as gasoline and windshield wiper fluid, be

aware that flammable fumes can ignite or explode. To help prevent fire and explosion:

• Use equipment only in well-ventilated area.

• Eliminate all ignition sources, such as cigarettes and portable electric lamps.

• Ground all equipment in the work area.

• Keep work area free of debris, including rags and spilled or open containers of solvent and gasoline.

• Do not plug or unplug power cords or turn lights on or off when flammable fumes are present.

• Use only grounded hoses.

•Stop operation immediately if static sparking occurs or you feel a shock. Do not use equipment

until you identify and correct the problem.

• Keep a working fire extinguisher in the work area.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system

component. See Technical Specifications in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical

Specifications in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For

complete information about your material, request Safety Data Sheets (SDSs) from distributor or

retailer.

• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine

manufacturer’s replacement parts only.

• Do not alter or modify equipment. Alterations or modifications may void agency approvals and

create safety hazards.

• Make sure all equipment is rated and approved for the environment in which you are using it.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent serious injury, including

eye injury, hearing loss, inhalation of toxic fumes, and burns. Protective equipment includes but is not

limited to:

• Protective eyewear, and hearing protection.

• Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufacturer.

Typical Installation

3A7279B 3

Typical Installation

There are multiple system configurations possible. The typical installations shown in FIG. 1 - FIG. 3 are the three

targeted applications for the Fluid Defender. Each typical installation shown is configurable as a single separate

channel. Follow all local codes and regulations for tank installations. Consult your local Graco representative or

distributor for system design assistance.

Waste Oil High Level Shut Off

FIG. 1

Typical Installation

4 3A7279B

Fresh Oil Low Level

FIG. 2

Typical Installation

3A7279B 5

Remote Bulk Fill Stop

FIG. 3

Overview

6 3A7279B

Overview

Fluid Level Sensors

The fluid level sensors detect the tank fluid level and

signals the Fluid Defender to activate the alarm and

deactivate the air control solenoid valve (if configured

on the specific channel).

Control level sensor: A level sensor connected as a

control level sensor to the Fluid Defender that controls

the output of an air control solenoid valve. Either a high

level or low level sensor may be connected as a control

level sensor

Monitor level sensor: A level sensor connected to the

Fluid Defender as a monitor level sensor that monitors a

tank fluid level. Either a high level or a low level sensor

may be connected as a monitor level sensor.

NOTE: Level sensors are preconfigured at the factory.

Do not attempt to reconfigure a level sensor by

changing the float orientation. High level sensors are

unable to be configured into low level sensors, and low

level sensors are unable to be configured into high level

sensors.

High Level Sensors

A sensor that is used to detect a full tank. The float is in

the down position and the sensor contacts are closed

during normal operation (FIG. 4, illustration a).

The float moves to the up position and the sensor

contacts are open during a high level condition,

triggering the Fluid Defender alarm (FIG. 4,

illustration b).

Low Level Sensors

A sensor that is used to detect an empty tank. The float

is in the up position and the sensor contacts are closed

during normal operation (FIG. 4, illustration c).

The float moves to the down position and the sensor

contacts are open during a low level condition,

triggering the Fluid Defender alarm (FIG. 4,

illustration d).

NOTE: For clarity, FIG. 4 does not show the splash

guard.

FIG. 4

Installation

3A7279B 7

Installation

Installation of Level Sensors

NOTE: Install level sensors in stationary tanks. The

sensors are not designed to monitor mobile tanks.

1. Apply thread sealant to the threads of a 2 npt bung

adapter to seal the tank.

2. Install level sensors away from inlet ports or pumps

to minimize inaccurate readings.

3. Ensure that the sensor body is free hanging from

the bung adapter housing.

NOTE: Level sensors are for vertical mounting only.

4. Set level sensor height by loosening the cord grip

on the bung adapter housing and adjust the length

of the suspended wire to set the desired activation

height.

NOTE: For guidance on calculation of installation height

of overfill devices, refer to Petroleum Equipment

Institute (PEI) RP600 Recommended Practices for

Overfill Prevention for Shop-Fabricated Above Ground

Tanks, Appendix A (www.pei.org).

a. The activation height is indicated on the splash

guard of the sensor.

b. High level sensors monitor the high tank fluid

level to prevent overfill.

NOTE: The level sensor height should be set to

activate following all local codes and regulations.

c. Low level sensors monitor the low tank fluid

level to prevent pump runaway conditions.

NOTE: The level sensor height should be set at

least 2 in. - 3 in. above the pump inlet.

d. Tighten the cord grip on the cable to finger

tight, plus one-half of a turn.

NOTE: Failure to properly tighten the cord grip may

cause the level sensor to move from the fixed

position.

5. Connect the level sensor wires following the

instructions in Fluid Defender manual, see Related

Manuals, page 1.

NOTE: Attach all accessory wires to the Fluid

Defender control box following all local codes and

regulations.

Reference the Technical Specifications, page 12,

for information on maximum wire runs and shielded

cable requirements.

All accessory circuits are low voltage (less than 48

VDC).

Operation

8 3A7279B

Operation

High Level Sensors

When the tank level is not at full, the float is in the down

position, normal condition, the contact is closed: no

alarm (FIG. 5, illustration a).

As the tank level rises and reaches the level sensor, the

float moves to the up position and opens the contacts

(FIG. 5, illustration b).

Low Level Sensors

When the tank is not empty, the float is in the up

position, normal condition, the contact is closed: no

alarm (FIG. 5, illustration c).

As the tank level falls and reaches the level sensor, the

float moves to the down position and opens the

contacts (FIG. 5, illustration d).

NOTE: For clarity, FIG. 5 does not show the splash

guard.

FIG. 5

Maintenance

3A7279B 9

Maintenance

Periodic Testing

Weekly (and before every remote bulk fill)

1. Press and hold the RESET button to test the siren,

rotating beacon, remote lights, and Fluid Defender

alarm lights.

2. Press the RESET button to reset the alarm.

Monthly

1. Relieve pressure following the pressure relief

instructions in your pump manual.

2. Remove the level sensors from the tanks and

manually raise or lower the float to verify that the

system goes into alarm mode.

3. Inspect the level sensors and remove magnetic

particles from fluid contamination that may interfere

with operation.

4. Manually test all of the accessories to verify they

are functioning properly.

5. Confirm that all wires are properly connected to the

Fluid Defender and accessories.

Recycling and Disposal

End of Product Life

At the end of a product’s useful life, recycle it in a

responsible manner.

Troubleshooting

Follow the pressure relief instructions in your pump

manual, before checking or repairing the system.

See Fluid Defender manual, Related Manuals, page 1

for Troubleshooting information.

AUTOMATIC SYSTEM ACTIVATION HAZARD

Unexpected activation of the air control solenoid

valves could result in serious injury from connected

equipment. The Fluid Defender manages the

connected air control solenoid valves that open the

air supply to connected equipment when the Fluid

Defender is powered,

Before installing, testing, or removing the Fluid

Defender, or any of its components, relieve pressure

following the pressure relief instructions in your

pump manual.

NOTICE

Disable the Fluid Defender or immediately replace

failed equipment upon any and all test failures.

Equipment failures will not allow the Fluid Defender to

monitor tank conditions and may result in a tank

overfill.

Kit

10 3A7279B

Kit

Part No. 25V592

FIG. 6

Ref. Description

1 Float

2 Retaining clip

3 Splash guard

4 O-ring

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Graco Capteur de sécurité

Graco

Graco Husky A Series Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur