Graco 246601 Manuel utilisateur

309828NINSTRUCTIONS

Important Safety Instructions

Read all warnings and instructions in this

manual. Save these instructions.

G–Force Direct-Drive Pressure Washer

2525LD

Model 246601, Series A & Series B

2300 psi (159 bar, 15.8 MPa) Maximum Operating Pressure

2500 psi (172 bar, 17.2 MPa) Maximum Working Pressure

2626LD

Model 249065, Series A

2600 psi (179 bar, 17.9 MPa) Maximum Operating Pressure

2750 psi (191 bar, 19.0 MPa) Maximum Working Pressure

ti3224b

ti6075a

2525LD

2626LD

GRACO INC. P.O. BOX 1441 MINNEAPOLIS, MN 55440–1441

Graco Inc. is registered to I.S. EN ISO 9001

2309828

Table of Contents

Symbols 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Warnings 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Component Identification 4. . . . . . . . . . . . . . . . . . . . . . . .

Pressure Relief Procedure 7. . . . . . . . . . . . . . . . . . . . . . .

Installing and Changing Spray Tips 12. . . . . . . . . . . . . .

Pump Service 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts Drawing 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Parts List 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Graco Phone Number 28. . . . . . . . . . . . . . . . . . . . . . . . . .

Warning Symbol

WARNING

This symbol alerts you to the possibility of serious

injury or death if you do not follow instructions.

Caution Symbol

CAUTION

This symbol alerts you to the possibility of damage to

or destruction of equipment if you do not follow instruc-

tions.

3309828

EQUIPMENT MISUSE HAZARD:

Misuse of pressure washer or accessories can cause the equipment to rupture or malfunction and

result in serious injury.

 Do not alter or modify any part or factory–setting

 Check equipment daily. Repair or replace worn or damaged parts immediately.

 Do not exceed maximum working pressure (MWPR) of the lowest–rated system component

 Use fluids and solvents that are compatible with the equipment wetted parts. See Specifications

page for this information.

 Wear hearing protection when operating this equipment.

 Do not “blow back” fluid; this is not an air spray system

 Follow Pressure Relief, page 7 before cleaning, checking or servicing equipment.

SKIN INJECTION HAZARD:

Spray from gun, leaks or ruptured components can inject fluid into your body and cause serious

injury. Fluid splashed in eyes or on skin can also cause serious injury.

 Fluid injected into skin might look like just a cut, but it is a serious injury. Get immediate

surgical treatment.

 Do not point gun at anyone or any part of the body.

 Do not stop or deflect leaks with hand, body, glove, or rag.

 Do not put your hand or fingers over the spray tip.

 TIghten fluid connections before you start this equipment.

 Engage the gun safety whenever you stop spraying.

 Follow Pressure Relief Procedure, page 7 if the spray tip clogs and before you clean, check

or service this equipment.

 Repair or replace worn or damaged parts immediately.

 Check hoses, tubes, and couplings daily. Do not repair high–pressure couplings. Replace entire

hose. Fluid hoses must have spring guards on both ends to prevent kinks and rupture.

TOXIC FLUID HAZARD:

Hazardous fluid or toxi fumes can cause serious injury or death if splashed in eyes or on skin,

inhaled, or swallowed.

 Know specific hazards of fluids you are using and take protective measures as recommended by

the fluid and solvent manufacturer.

FUEL HAZARD:

Fuel is combustible. When spilled on a hot surface it can ignite and cause a fire.

Do not fill fuel tank while engine is running or hot.

EXHAUST HAZARD:

Exhaust contains poisonous carbon monoxide, which is colorless and odorless. Do not operate this

equipment in a closed building.

4309828

Component Identification

Gun and Wand

High Pressure

Hose Connection

On/Off Engine Switch (side)

Water Pump Oil Fill

Engine Oil Fill

Tip Storage Hose Rack (a) /

Gun Holder (b)

(b) (a)

Garden Hose

Connection

Pressure Unloader

Adjustment Knob

ti3226a

Thermal Valve

*Cart handle can be re-

moved to create a com-

pact profile for storage

and transporting. Push

in release button on

each side of handle.

(Fig. 1) Pull handle off

lower frame. (Fig. 2).

Rotate handle 180and

reposition over lower

frame. (Fig. 3) Push

down on handle until un-

til release buttons en-

gage.

Handle Release Button*

ti6077a

ti6079a

Fig. 1 Fig. 2 Fig. 3

5309828

Shipping Damage

Check pressure washer for shipping damage. Notify carrier immediately if there is any damage.

Initial Setup

Oil

Engine is shipped without engine oil. Add Graco SAE 10W–30 engine oil (included) and confirm oil level is within

an acceptable range according to the Honda Owner’s Manual (included).

(cold)

ti5952a

Fuel

Fill fuel tank.

ti5953a

Pump plug

Remove red water pump plug (A) and replace with attached black vented pump plug (B).

Red water pump plug

Black vented pump plug

TI10675A

6309828

Installation

Connect High–Pressure Hose and Gun

Connect high–pressure hose between the pump outlet and gun inlet.

Both of these connections are made with quick couplers.

Install Spray Tip

Install spray tip on wand. Installing and Changing Spray Tips,

page 12). If you are using a Sandblasting Kit, see its separate

manual for installation instructions.

Connect to Water Supply

Connect hose with at least a 3/4 in. (19 mm) ID from water supply

to 3/4 in. garden hose inlet on the pressure washer. The supply

hose should not be more than 50 ft (15 m) long.

Before you connect garden hose to pres-

sure washer, check local plumbing codes

regarding cross–connection to water

supply. If required, install backflow pre-

venter.

If inlet water pressure is over 60 psi (4.1

bar), a regulating water valve must be

installed at garden hose connection.

Do not exceed 104°F (40°C) inlet water

temperature.

CAUTION

Note: Water source must have a minimum flow rate equal to that of pressure washer.

ti3228a

ti3229a

ti3457a

Note: Adapter kit 249101 can be used to connect

two high pressure hoses together.

ti7345a

7309828

PRESSURE RELIEF

Follow these instructions whenever you are instructed to relieve pressure, stop spraying for

more than 10 minutes, check or service the equipment, or install or clean the spray nozzle.

1. Engage trigger safety latch

2. Turn pressure washer off

3. Remove ignition cable from spark plug.

4. Shut off water supply. Disconnect from water.

5. Disengage trigger safety latch. Trigger gun to relieve

pressure. Then re–engage the safety latch.

Note: If you suspect that the spray tip or hose is clogged or that pressure has not been fully relieved after

following the steps above, disengage the trigger safety latch and trigger the gun to relieve pressure.

TI3233A

TI3234a

8309828

1. Check oil level of engine.

Startup

Always use this startup procedure to ensure that the pressure washer is started

safely and properly.

Always engage gun trigger safety latch when you stop spraying. This reduces the risk of fluid injection or

splashing in eyes or on skin if gun is bumped or accidentally triggered.

Always observe the CAUTIONS in this section to avoid costly damage to pressure washer.

If you use the Sandblaster Kit, see Sandblaster Kit Manual for detailed cleaning information.

Operation

2. Check fuel level.

3. Turn on water supply.

Never run pressure washer without wa-

ter. Costly pump damage will result.

Always be sure water supply is complete-

ly turned on before you run pressure

washer.

CAUTION

9309828

4. Trigger gun until a constant stream of water sprays from tip indicating air is purged from the system.

5. Be sure spark plug ignition cable is pushed firmly onto spark plug.

6. For Model 2525LD ONLY, move

throttle to Rabbit (fast) position first.

For all models, (then) move choke to

CHOKE position.

 Do not allow pressure washer to idle more than 10

minutes. This causes circulating water to overheat and

serious damage to the pump. The pump is equipped

with a thermal valve to help prevent severe damage if

circulating water is overheating.

 Turn off pressure washer if it will not be spraying at

least every 10 minutes or if thermal valve activates. If

heated inlet water is used, reduce this time.

 Do not operate pressure washer with inlet water

screen removed. This screen helps keep abrasive

sediment which could clog pump or damage cylinders,

out of pump.

 Do not pump caustic materials.

CAUTION

7. Pull the starter rope quickly to start the engine. Pull and return the

rope until the engine starts. HINT: Placing one foot on the pres-

sure washer as a brace provides better leverage.

NOTE: For easier starting, have one person start pressure washer while another triggers gun.

ti3240a

ti3242a

Model 2525 Only

All models

10 309828

Trigger Safety Latch

Always engage the safety latch when you stop spraying.

Always engage trigger safety latch when you stop spraying even for a moment. The engaged

safety latch prevents the gun from being triggered accidentally by hand or when dropped or

bumped. Be sure latch is pushed fully down or it will not prevent the gun from being triggered.

TI3233A

TI3234a

Safety ON Safety OFF

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Graco Nettoyeur haute pression

Graco

Graco Hydra-Clean 308-532 Manuel d'utilisation

Graco

Graco 246343 Manuel utilisateur

Graco

Graco Hydra-Clean 1020E Instructions- Manuel d'utilisation

Graco

Graco Hydra-Clean 205-985 Manuel d'utilisation

Graco

Graco Hydra-Clean 2104G Manuel d'utilisation

Graco

Graco AquaMax 3540GHW Manuel utilisateur

Graco

Graco Hydra-Clean 3035 Manuel d'utilisation

Graco

Graco 3325 HA-DD Manuel d'utilisation et d'entretien

Graco

Graco Hydra-Clean 4040 Instructions- Manuel d'utilisation

Graco

Graco HYDRA-CLEAN 3540 Manuel d'utilisation

Graco

Graco AquaMax 804594 A Series Manuel d'utilisation

Graco

Graco Hydra-Clean 2510 Manuel d'utilisation

Graco

Graco Hydra-Clean 312585P Manuel de la liste des pièces

Graco

Graco Hydra-Clean 1035 Manuel d'utilisation

Graco

Graco Hydra-Clean 2540 Manuel d'utilisation

Graco

Graco HYDRA-CLEAN 1535 Manuel d'utilisation

Graco

Graco Hydra-Clean 247549 Manuel d'utilisation

Graco

Graco 244811 Instructions de montage

Graco

Graco HYDRA-CLEAN 2000 Manuel utilisateur

Graco

Graco 2500 psi Manuel d'utilisation

Graco

Graco HYDRA-CLEAN 826 Manuel d'utilisation

Graco

Graco Hydra-Clean 308-517 Manuel d'utilisation

Graco

Graco Xtreme XL Packages 334645B Manuel d'utilisation

Graco

Graco Series A Manuel d'utilisation

Manuels Nettoyeur haute pression populaires d'autres marques

Shark

Shark RG-232637 Manuel utilisateur

Shakti Technology

Shakti Technology S3 Manuel utilisateur

Kärcher

Kärcher K 4 Pure Manuel utilisateur

Porter-Cable

Porter-Cable D25806-025-2 Manuel utilisateur

REM POWER

REM POWER HDEm 662 Manuel utilisateur

Landa

Landa HS-3000 Manuel utilisateur

Craftsman

Craftsman 580.752270 Manuel utilisateur

HIKOKI

HIKOKI AW 100 Manuel utilisateur

Delco

Delco DC 1302 Manuel utilisateur

Kärcher

Kärcher K 3 Full Control Manuel utilisateur

BIEMMEDUE

BIEMMEDUE 120/10 - 170/13 Manuel utilisateur

ARKSEN

ARKSEN 014-HG-14141-HR Manuel utilisateur

Black & Decker

Black & Decker PW1700SPX Manuel utilisateur

Kärcher

Kärcher 595 - SPARE Mode d’emploi

Kranzle

Kranzle B 10 200 Manuel utilisateur

Stihl

Stihl RE 90 Manuel utilisateur

Husky

Husky HU80911 Manuel utilisateur

PowR-Quip

PowR-Quip PQ-2600 Manuel utilisateur