Graco 257528 Manuel utilisateur
- For servicing FinishPro 290 and FinishPro II 295 sprayers -
2600 psi Models: 257528
2800 psi Models: 257529
3000 psi Models: 24U996
Pressure Relief Procedure
Important Safety Instructions
For detailed instructions and warnings,
see sprayer manual.
Toreducetheriskofinjuryfrominjection,alwaysfollow
this procedure when instructed to relieve pressure,
stop spraying, service equipment, or install or clean
spray tip.
1. Set power/function selection switch to OFF and
unplug sprayer.
2. Turn pressure knob to lowest setting.
3. Hold gun to side of grounded metal pail. Trigger the
gun to relieve pressure.
4. Turn prime valve to PRIME.
If you suspect spray tip or hose is completely clogged, or
that pressure has not been fully relieved after following
these steps, VERY SLOWLY loosen tip guard retaining
nut or hose end coupling to relieve pressure gradually,
then loosen completely. Clear tip or hose obstruction.
313899B
Repair Kit
Pressure Control
Replacement Kit
ti9346a
EN
2 313899B
Removal
1. Relieve Pressure (see cover) and unplug power
cord.
2. Remove pail hook (G) from bottom of front cover
(C).
3. Removesuctiontubeassembly(W)anddraintube
(U).
4. Remove four cover screws (B) and front cover (C).
5. Remove yoke (D) and guide rods (E). Clean if nec-
essary.
6. Disconnectpressurecontrolharness(F)fromcon-
trolboardconnector(H)atbackofdrivehousing(J).
Using fingernail or tip of small, flat-blade screw-
driver, press tab on right side of connector to
release.
7. Remove pump (M) from drive housing (J).
8. Place pump (M) on workbench or in vise.
9. Unscrewpressurecontrolswitch(P)frompump(M).
Verify that o-ring seal (R) is also removed from
pump (M).
Installation
• Read all Installation Notes on back of this page.
1. Screw new pressure control switch (P) into pump
(M), and torque to 140-160 in-lb (16-18 N•m). Do
not overtighten, damage could occur.
2. Routepressure controlharnessthrough retention
clip(K),andconnecttocontrolboardconnector(H)
at back of drive housing (J) as shown in Wiring
Detail.
3. Install pump (M) on mounting pins (S). Make sure
plastic washers (T) are between drive housing (J)
and pump and that pressure control wires are not
pinched between pump and drive housing.
4. Installyoke(D)withrodcapinslotofyokeasshown
in Rod Yoke Detail on next page.
5. Checkfinal assembly against DriveTrain Detail on
next page.
6. Install front cover (C) and cover screws (B).
7. Install pail hook (G) to bottom of front cover (C).
8. Installsuctiontubeassembly(W)anddraintube(U)
on new pump (M).
9. TurnPressureControlKnob(P)clockwiseasfaras
itwillgo.Applypressurecontrollabeltoknob.Posi-
tion as shown below.
+
ti14315a
313899B 3
Installation Notes
To prevent misalignment, assemble sprayer tipped onto back of enclosure.
R
S
B
C
P
M
E
D
D
C
F
TT
S
U
W
X
J
A
H
ti13842a
Rod/Yoke Detail
Pump
G
ear
/
Yoke
Replacement
Kit
Replacement Kit
G
K
Y
Drive Train Detail Wiring Detail
Pressure Control Switch
Replacement Kit
257528 (2600 psi Models)
257529 (2800 psi Models)
24U996 (3000 psi Models)
Take care to not pinch harness (F) between pump (M) and any part of drive housing (J) or between front cover
(C) and drive housing.
For best cover (C) alignment, tighten lower two cover screws (B) first, then top two. Torque screws to 70 to 80 in-lb
(8 to 9 N•m).
For yolk (D) installation, eccentric bearing (Y) on gear (X) must touch top of pump rod. Turn gear to move eccentric
bearing to proper height.
Ifyokeguiderods(E)dropoutofpositionduringassembly,damagewilloccurwhencoveristightened.Alwayscheck
position of guide rods before tightening cover.
Apply light coat of oil.
Apply one or two drops of thread locking adhesive (included in kit) to threads of pressure control switch (P).
Torque to 140-160 in.-lb (16-18 N•m).
4 313899B
For the latest information about Graco products, visit www.graco.com.
TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
)RUSDWHQWLQIRUPDWLRQVHHZZZJUDFRFRPSDWHQWV
2ULJLQDOLQVWUXFWLRQV This manual contains English. MM 313899
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2009, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revised February 2014
Ce manuel convient aux modèles suivants
2
Autres manuels Graco Contrôleurs
Graco
Graco Xtreme-Wrap 26C930 Manuel utilisateur
Graco
Graco 104266 Manuel utilisateur
Graco
Graco LC0250 Manuel de la liste des pièces
Graco
Graco Series B Manuel utilisateur
Graco
Graco 1093 Guide de dépannage
Graco
Graco Series A Manuel de la liste des pièces
Graco
Graco GLC 2200 Manuel utilisateur
Graco
Graco 214706 Manuel utilisateur
Graco
Graco Advanjet Diaphragm-Jet HV-2000 Instruction manuelle
Graco
Graco PrecisionFlo XL Manuel utilisateur
Graco
Graco 24E025 Manuel d'utilisation
Graco
Graco PRECISIONMIX 231-119 Manuel d'utilisation
Graco
Graco 24G621 Manuel de la liste des pièces
Graco
Graco ProControl 1KS Mode d’emploi
Graco
Graco 114-459 Manuel d'utilisation
Graco
Graco 214895 Manuel d'utilisation
Graco
Graco 3A7639A Manuel utilisateur
Graco
Graco InvisiPac Manuel utilisateur
Graco
Graco Harrier EZ-Batch Manuel utilisateur
Graco
Graco Trabon LC-1000 Manuel utilisateur
