GPS Tracker TV680 Manuel utilisateur
1
TV680 GPS Watch User’s Manual
2
Table of Contents
Chapter I Preface………………………………………………….. ………………………………………………………..3
I．General……………………………………………………………. ……………………………………………………....3
II．Notices…………………………………………………………….. ……………………………………………………..3
Chapter II about the Device………………………………………………………………………………………………...3
1. Appearance…. ……………………………………………………………………………………………………………..3
2. Product Features……………………………………………………………………………………………………..…….4
3. Product Specification……………………………………………………………………………………………..……….5
Chapter III Usage Preparation………………………………………………………………………………..……………6
I.Accessories…………………………………………………………………………………………………..……………..6
II.Appearance and Interface………………………………………………………………………………..……………...7
III.Charge the Battery……………………………………………………………………………………..……………….8
IV.Installation of SIM Card……………………………………………………………. ……… ….. ….… ……………...8
ChapterIV Commands Corresponding to and Operation Method of Basic Functions………….……… …….8
1. Location Inquiry…………………………………………………………………………….. ….…………………….9
2. Setup of Centre Number…………………………………………………………………..………………………….9
3. Bi-directional Call Function……………………………………………………………..…………………………...9
4. Adjust Receiver Volume…………………………………………………………………..…………………………..10
5. SOS Function……………………………………………………………………………..…………………………...10
6. Monitoring Function……………………………………………………………………..…………………………...11
7. Regular Upload Interval Setup…………………………………………………………..…………………………..11
8. Function of Changing Password…………………………………………………….…..…………………………11
9. Set User Name Command……………………………………………………….. ….……………………………...12
10. Set APN Command………………………………………………………………..……. ….………………………..12
11. Set Server Address Command………………………………………………………...……………………………13
12. Low Voltage Alarming Function………………………………………………….. …. …………………………....13
13. Method to Set Time Zone………………………………………………………….…..……………………………...13
14. Electronic Fence Function…………………………………………………………………..……………………….14
15. Auxiliary Functions……… …………………………………………………………………..………………………15
Notices………………………………………………………….. ………………………………….……………………….....15
3
Chapter I Preface
I. General
TV680 represents the perfect combination of GSM and GPS technologies. This model, with its precise dimensions
and compact appearance, expresses the advanced workmanship in the GSM and GPS field. It is a typical design
combing communication products and GPS services.
As a professional security and positioning company, we will provide you with more and better products and services.
Before using the watch, please spend several minutes reading this user’s manual in order to get to know about
operation details and obtain better services.
II. Notices
1. Please read this user’s manual carefully and always use correct operation methods to prevent any possible errors.
2. This user’s manual is for reference only. If some contents and operation steps are inconsistent with those for the
actual product, the latter will prevail.
3. The defaulted password of this product is 0000.
4
Chapter II about the Device
TV680, as a personal remote positioning device made up of GPS module and GSM/GPRS module, is compact in
dimensions with high accuracy. On the basis of GPS satellites and under dynamic conditions, it can provide you with
accurate and correct location information. With such features, it can be used to protect and look for our old people
and children. It can also be used for safety purpose and other purposes, such as remote positioning to protect
property safety.
1 Appearance
2 Product Features
● Inbuilt GPS Module
● Internet positioning service center, used to receive and send positioning information
● GSM /GPRS modem supports Quad frequency bands, i.e. 850/900/1800/1900 MHz
● High-sensitivity, new workmanship and the most advanced GPS chip
● Can work effectively in limited space such as urban canyon
● Low energy consumption
● Fast signal acquisition
● Supports single positioning and continuous tracking;
● Supports alarming and remote monitoring
● Supports fast dial button
● Supports the location information inquiry by SMS and Internet
● May monitor without disturbing the tracked person and realizes real-time tracking;
● Can position the holder by call or SMS
● In emergency, press the SOS button to have an accurate positioning
5
3 Product Specifications
(1). Technical Specifications
GSM module GSM 850/900/1800/1900 MHz Quad frequency
GPS sensitivity -163dBm
GPS center frequency L1, 1575.42MHz
GPS positioning accuracy 5-25m
GSM positioning accuracy 100-500m
Speed accuracy 0.1 m/s
Time accuracy Synchronous with GPS
GPS Datum WGS-84
Hot start < 1s
Warm start < 38s
Max. altitude 18000m
Max. speed 515m/s
Gravitational acceleration ﹤4g
(2). Others
Operating temperature -20---65℃
Humidity 5%---95%
Dimensions 64.5mm×45.5mm×17.5 mm (main unit)
Voltage Rechargeable 450mAh battery
Power supply DC5V
Standby time >48h
Buttons SOS button for emergency aid; Call 1, Call 2,
Switch on / off buttons, interface switch button
6
Chapter III Usage Preparation
I. Accessories
1. Main unit
2. USB data cable
3. Charger
4. Headset cable (optional)
5 Battery
II. Appearance and Interface
1. Appearance and Buttons
Five buttons are equipped with this watch
The upper left button serves for switch-on and hold-on
The bottom left button serves interface switch
While the upper right button for predetermined number 1
Middle right button for emergency aid (SOS button)
The bottom right button for predetermined number 2 as shown
In picture 1:
7
2. Interface Definition
GSM signal strength is indicated on the upper left corner of the main interface as showed in picture 2:
Bottom left button is for interfaceswitch as showed in picture 3:
III. Charge the Battery
Please use up the battery and discharge it for 2-3 times and then charge the battery for at least 12 hours for initial
use, in order to keep the quality of the battery.
The normal charging time of this product is 4-5 hours.
Put the battery into the inside of the terminal and connect the charger to 100V/220V AC power supply to charge
the battery. Then the power indicator on the upper right corner of the terminal screen will keep strolling as
showed in picture 3-1:
( picture 3-1 )
When the battery is fully charged, the power indicator will stop strolling; if the battery is charged on switch-off
mode, the following picture 3-2 indicates the charging is finished:
( picture 3-2 )
8
Notes:
Please always use the charger offered by the supplier. Dangers damages of the product caused by usage of any
unconfirmed charger will not be compensated and repaired.
The battery should be charged in time when the terminal automatic shutdown or being alarmed with low power.
The standby duration and call duration offered by the supplier is calculated in perfect functional mode, in practice,
working hours of the battery may vary due to difference of internet service, functional mode and usage mode.
Disconnect the terminal and charger as soon as possible after the battery is well charged.
IV. Installation of SIM Card
Open the back cover, then you will see the place where the SIM card is placed. Then push the SIM card into the slot
until it comes into its proper position completely and consolidate it with the dome sheet nearby.
Choose SIM card:
The type of the SIM card is GSM card (the SIM card of China Mobile is recommended).
Ensure sufficient money is within the SIM card in order to pay the communication fee.
Prepare a SIM card for mobile phone (the SIM card of China Mobile is recommended), make sure that the card
has opened such functions of Caller ID and sending and receiving SMS. If service platform real-time tracking is
in need, then GPRS function should be open.
Chapter IV Commands Corresponding to and Operation Method of Basic Functions
1. Location Inquiry
SMS Inquiry
Send command 666 plus password to the terminal, then the terminal will return a piece of detailed latitude and
longitude message.
For example: 6660000
9
Google link function
Send command 999 plus password to the terminal, then the terminal will return a piece of detailed url. The google link
can show google map on the mobile phone after be clicked.
For example: 9990000
2. Setup of Centre Number
Set the centre number by SMS through the mobile phone, after the setup is successful, then the mobile phone that
sending the SMS will receive the “&710&successful setting&&” response message from the terminal.
Command format: #710# center number # user password ##
For example: #710#134xxxxxxxx#0000##
Note: All alarming information thereafter including SOS, low power, electronic fence, etc will be returned to that
number.
3. Bi-directional Call Function
Incoming calls can be rejected by pressing upper left button or received by pressing middle right button.
Send the command in form of SMS to the terminal via mobile phone. After the setup is successful, the mobile phone
will receive the “&710&successful setting&&” response message from the terminal.
Setup format: #711# Call1# Call2 # Call3 # 0000##
Notes: After the setup is successful, press the upper right button for a while, then the terminal will automatically dial
the first phone number. Press the bottom right button, then the terminal will automatically dial the second phone
number.
4. Adjust Receiver Volume
While making phone calls, the user could press upper or bottom right button to adjust receiver volume.
5. SOS Function
If a ward number (predetermined number in item3) is set, when the ward encounters emergency and presses the
10
SOS button, the terminal will send alarming information to the center number and dial the three ward numbers in
turn.
SOS SMS format: IMEI number: SOS (information about latitude and longitude or base station)
Example: 356823031017473:SOS（11354.6397,E,2232.6283,N）or 356823031017473:SOS（26280E77）
Remarks: when interface in picture 5 appears on the phone, the terminal will skip to standby mode automatically;
sound and interface during the dialing will be completely shielded.
6. Monitoring Function
The guardian may send SMS 555 plus password to the terminal of the ward, then the ward terminal will automatically
call back to the mobile phone of the guardian and the guardian may hear the sound of the surroundings within 10m
around the ward.
SMS format: 5550000
Remarks: 0000 is the initial defaulted password and in practice the password could be set by the user.
7. Regular Upload Interval Setup
The defaulted upload interval of this product is 0, meaning that the defaulted GPRS is closed. The user may change
the parameter according to actual demand.
Command format: # command number 730# Sampling interval # Pieces of uploads # User password ##
Example: #730#20#4#0000##
Notes: The parameter “20” indicates getting one point every 20s; after getting points accumulatively for 4 times,
upload one piece of positioning information with the upload interval as 20*4=80s. The user may change this
parameter as the case may be.
8. Function of Changing Password
Send the SMS “#770# User new password # User old password ##” by mobile phone to the terminal number, after
successful sending, the mobile phone with such setup will receive one piece of ‘&770&successful setting&&’
Table des matières
