gplink GWD050 Manuel utilisateur
Power Generation
Installation Guide
www.gplink.com
Satellite Tracking and Monitoring Solutions
Contact gplink at +1.252.504.5113 at least 24 hours
prior to scheduled installation for activation of units.
(48 hours on weekends)
®
2Power Generation Installation Guide Version 2.0.0 - July 2016
Contents
1. Introduction and Purpose 3
2. Installation & Components 4
2.1 Installation 4
2.2 Power Harness 4
2.3 J1939 Harness 5
2.4 MODBUS Harness 5
2.5 Analog Inputs and Outputs 6
3. 2-Inch User Interface 7
3.1 Operation 7
3.2 Diagnostics
4. gplink Concierge & Technical Support 11
4.1 Transferable Limited Warranty 11
3Power Generation Installation Guide Version 2.0.0 - July 2016
1. Introduction and Purpose
Notice - The gplink system is only an aid to operation of the equipment it is installed on. The performance
of the system and the system performance specications can be affected by many factors including but
not limited to equipment failure, environmental conditions, improper installation, handling and/or use.
This device should not be used for any navigational or safety purpose. The gplink system is used at your
sole risk and in no event shall gplink, Inc. be held liable for any costs, losses, liabilities, damages, expense
or claims of any nature incurred or sustained in respect of this device or its use. You further indemnify and
hold harmless gplink Inc. and their partners from any liability or loss resulting from use of the device.
Parts List (Single Band)
Part # DESCRIPTION QTY.
AN9003
AN9004
GPS/GSM antenna
GPS/Iridium antenna 1
GWD050
GWD051
GPLink (MTU) GSM
GPLink (MTU) Iridium 1
HN9040 Power Harness 1
HN9044 J1939 CAN Harness 1
HN0671 Antenna Extension 2
HW0245 Mounting Hardware 1
BK9990 Antenna Mounting bracket 1
WI0020 Installation Manual 1
Contact gplink at +1.252.504.5113 at least 24 hours (48 on weekends)
prior to scheduled installation for activation of units.
HN9042
GWD050 - GSM GWD051 - Iridium BK9990
HN9041HN9040
4Power Generation Installation Guide Version 2.0.0 - July 2016
2. Installation & Components
2.1 Installation
Locate an area to mount the antenna less than 3 meters from the Mobile Transmitting Unit (MTU). Mount the
antenna, using the Antenna mounting bracket (BK9990), and run the cables to MTU.
a) Mount the MTU in an area where there is easy access to antenna cables and the battery or power source.
b) GPS Connect the Blue colored wire to the J1 connector on the MTU.
c) GSM Connect the Yellow colored wire to the J2 connector on the MTU if connecting a GMS device.
or
SAT Connect the White colored wire to the J3 connector on the MTU if connecting an Iridium device
Connect cables to mounting location of the MTU.
2.2 Power Harness
(HN9040) (See the Wiring Diagram)
a) Connect the power harness (HN9040) (Gray Connector (A)) to the MTU at receptacle “A”
b) Connect the RED wire directly to a continuous 12-24 vDC source or the positive battery terminal.
c) Connect the BLACK wire to a good ground, preferably the negative battery terminal.
Note:The connector and receptacle are keyed so that they can only go together one way. Please be sure to line up the
guides on the connector with the slots in the receptacle when connecting the harness to the MTU.
J1 J2
J3
4-pin
Deutsche
connector
A
5Power Generation Installation Guide Version 2.0.0 - July 2016
2.3 J1939 Harness
(HN9041) (See the Wiring Diagram)
a) Connect the J1939 harness (HN9041) (Black Connector (B)) to the MTU at receptacle “B”.
b) Connect the GREEN (CAN High),YELLOW (CAN Low) and BARE (Shield) wires to the corresponding J1939
connector wires on the generator.
c) The BLUE and GRAY wires are available for use as outputs.
2.4 MODBUS Harness
(HN9042) (See the Wiring Diagram)
a) Connect the four pin Deutsche connector to the Deutsche connector on the Power harness (HN9040).
b) Connect the WHITE (D+), GREEN (D-) and BLACK (Ground) wires to the corresponding connector on the
Genset controller.
J1939 B
Genset
Controller
4-Pin
Deutsche
connector
A
B
6Power Generation Installation Guide Version 2.0.0 - July 2016
2.5 Analog Inputs and Outputs
a) From the Power harness (HN9040) connect the BROWN wire to any 240/33 fuel level sender input.
b) Other Inputs and Output connection are available.
Wiring diagram
Figure 1
BLACK
Ground
BROWN
Fuel
ORANGE
Switched IN
Shield
Output
Output
CAN (low)
CAN (high)
RED
BLUE
BARE
YELLOW
GREEN
Main
Battery
J1/GPS - Blue wire to Antenna
B
B
AA
HN9040
HN9042
HN9041
Serial # KWD304-VMS000 FPN:KTW304
PASS 02-28-09
SIM CARD
IRIDIUM MODEM #
FCC ID:PY76220511
Not used - 1
Not used - 4
Not used - 5
Not used - 6
Output - BLUE - 2
Output - GRAY - 3
12 - Not used
11 - Not used
10 - Not used
8 - Not used
9 - BLACK
10 - RED
11 - WHITE
12 - GREEN
7 - BLACK - Ground
PURPLE - 1
Switched IN - ORANGE - 2
Fuel - BROWN - 3
Not used - 4
RED/WHITE - 5
RED - 6
9 - YELLOW - CAN(High)
8 - BARE - Shield
7 - GREEN - CAN (Low)
J1
J2
J3
J3/SAT - White wire to Antenna - GWD051
J2/GSM - Yellow wire to Antenna - GWD050
(B) Black
connector
(A) Gray
connector
J1939 Cable
J1939
FARIA BUS
GRAY
BLACK
GREEN WHITE
+ 12-24 vDC -
+12-24vDC
User Interface
(optional)
WHITE - D(+)
BLACK - Ground
GREEN - D(-)
GWD050/GWD051
7Power Generation Installation Guide Version 2.0.0 - July 2016
3. 2-Inch User Interface (Optional)
The 2-inch User Interface displays the status of communications to the MTU, (mobile transmitting unit).The MTU uses
GPS and at least one communication channel, (either GSM/GPRS or Iridium satellite) to send vehicle or equipment status
and position.
Connect the User Interface with the wiring harness (HN9040) as shown in the Wiring Diagram.
3.1 Operation
When power is applied your interface display will beep and the LCD will illuminate.To show that the MTU is running the
2-inch display will show one of the following messages:
1. “Wait” is the boot up message, which indicates the unit is trying to communicate with the MTU.
2. “Comm” Indicates the MTU is running, has a GPS x and has at least one communication channel open/available,
(GSM or Iridium).
8Power Generation Installation Guide Version 2.0.0 - July 2016
3.“No-Comm” with RED LED’s continuously on indicates the MTU is running but cannot get a GPS x, cannot communicate,
(via GSM or Iridium), or both GPS and communication links are down.
3.2 Diagnostics
Press the “S” button to enter the STATUS mode.Then, press “Mode” to step through status displays as follows:
For dual band system, (GSM and Satellite), GSM signal strength will display from 0, (no signal) to 5, (best signal).
9Power Generation Installation Guide Version 2.0.0 - July 2016
Sat signal strength, will display from 0, (no signal), to 5, (best signal).
GPS PDOP X 100, (a PDOP of 1.23 will read 0123,etc),9999 (means no GPS signal), For PDOP lower numbers represent
a better connection.
Main battery voltage X100 (battery voltage of 12.34Volts will appear as “1234”).
10Power Generation Installation Guide Version 2.0.0 - July 2016
Back up Battery voltage The Back-Up voltage will be the same value as the main battery voltage. The wires are tied
together in the harness.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels gplink GPS
