goSilver Plus Manuel utilisateur
Manual
goSilver Plus / Plus 8
Content
01 Foreword Page 4
02 Operation Page 5
03 Selection menu Page 6
04 Setting options Page 7
05 Start of electrolysis Page 9
06 Status screen Page 10
07 Final screen Page 13
08 Production Page 14
09 Notes Page 18
10 Contact Page 19
4
01 Foreword
Thank you very much for choosing the
goSilver Plus for your own production of
colloidal silver.
The software together with the TRUEppm®
technology - taking into account all the
additional factors - fully automatically
ensures a consistently high quality of
production.
With the goSilver Plus, you can produce
both colloidal silver with cold water & ionic
silver under constant heat of about 90° C
(In this case please read the safety note on
page 18.)
5
The operation of the device is simple and
intuitive. All desired settings can be made
with the use of the multifunctional rotary
knob.
After starting the electrolysis, the status of
the production can be checked on the dis-
play. At the end of the electrolysis, the final
screen shows a summary of the respective
production.
Please familiarize yourself with the ope-
ration of the goSilver Plus before the first
production.To do this, plug the power plug
into a power outlet and connect USB cable
with the device.The start screen appears
on the display.
02 Operation
The rotary switch can be rotated in both
directions and / or pressed down. Pressing
selects or confirms a selection.
6
03 Selection menu
After the start screen, the selection menu
appears automatically. The arrow (cursor)
is in the line „go!“. If the adjusted values fit,
you can start the electrolysis directly.
If you want to set the parameters (amount
of water, ppm concentration, etc.) you can
turn the rotary knob to reach the other
lines and choose your desired settings.To
do this, move the cursor to the line that you
Liters 1,000
ppm 50
go!
>
By turning the rotary knob you can navigate
through the selection menu or, after fixing a
selection, you can specify the corresponding
value.
7
want to change. By pressing, the value can
be edited - the value now flashes.
By turning, the desired value can now be
set and fixed by pressing it again. Further
details under „04 settings options“.
All set values are being saved also when you
shut off and restart the device.
Liters 1,000
ppm 100
go!
>
04 Setting options
04.1 Liters
You can set amounts of water between 0.1
and 40 liters.
04.2 ppm oder mg/L
You can choose between the unit ppm or
milligrams per liter (mg / L). Concentrations
of 0.5 to 99.9 mg / L or 5 to 999 ppm (old)
are possible.
Depending on which selection is pre-set in
point 03.4 or if it has already been changed
there, the concentration in the respective
unit is displayed here.
8
5More settings
Moving the cursor beyond the top of the
display will take you to more settings.
04.3 Water — warm oder cold
You can configure the device for production
with cold or hot water. For production with
hot water, please read the warning note on
page 18!
Beep 1s
Language English
Unit ppm
Water cold
>
04.4 Unit — ppm or mg / L
You can set the concentration either in
ppm (old and as usual) or in milligrams per
liter (mg / L) or TRUEppm (see explanation
on page 18). TRUEppm is exactly one tenth
of the usual ppm.
04.5 Language — German / English
You can change the operating language of
your goSilver Plus to German or English.
The change comes into effect after fixing
the setting.
04.6 Beep - 0, 1, 3, 6, 9 s
At the end of the manufacturing process,
a beep will sound. The duration of the
sound can be adjusted. Off (0s) or 1, 3, 6, 9
seconds.
9
After reviewing all settings, you will not need
to return to this screen until you wish to
make a change in the future. All settings are
permanently saved (even after switching off
the device).
05 Start of electrolysis
Press ‚go!‘ To start production with all set
parameters, if distilled water is used and
the software‘s water test is positive.
For safety reasons the device will not start
if you use tab water, heavily contaminated
water or even colloidal silver, even if only in
small quantities.
If the water test is positive, the device dis-
plays the message:„Water ok.“
Please use
destilled water!
10
If you want to make Colloidal silber with hot
water (90 ° C), please read warning note on
page 18!
Water ok! 06 Status screen
During the manufacturing process, the
most important settings are displayed and
additional information can be used to mo-
nitor the progress of the electrolysis.
06.1 Liters
The selected amount of water
06.2 ppm or mg/L
Depending on the setting, either the selec-
ted ppm and the ppm already generated or
the selected mg / L and the already genera-
Liters 0,25
ppm 15/50
Time left 0:05h
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels goSilver Système de filtration d'eau
Manuels Système de filtration d'eau populaires d'autres marques
Wisy
Wisy LineAir 100 Manuel utilisateur
Schaffner
Schaffner Ecosine FN3446 Series Manuel d'utilisation
Pentair
Pentair FLECK 4600 SXT Guide de l'utilisateur
H2O International
H2O International H20-500 Manuel utilisateur
Renkforce
Renkforce 2306241 Manuel utilisateur
Neo-Pure
Neo-Pure TL3-A502 Manuel utilisateur
