Google Nest x Yale Pro Manuel utilisateur
2019 | Condential and Proprietary | Do not distribute
Nest x Yale Lock
Nest Pro Guide
2019 | Condential and Proprietary | Do not distribute
Any Qs?
Pro line: 855-VIP-NEST or 855-847-6378
Welcome to the Google Nest x Yale Lock Pro Guide.
Here you’ll nd all you need to install the Nest x Yale Lock
and unlock convenience for the customer.
Got Feedback? Tell us what you think here.
Section Page
Technical specs
A look inside the Nest x Yale Lock.
5
Installation guides
A step-by-step guide to installing the Nest x Yale Lock.
6
Category expeise
Know the world of sma locks.
16
Beer Together
See how the Nest x Yale Lock works with other Google Nest
products.
17
Additional resources 19
Hey there!
2019 | Condential and Proprietary | Do not distribute
●Nest x Yale Lock
●Nest Connect (may be required, if not included)
●Installation guide
●Strike plate
●Mounting screws
●4 AA alkaline baeries
All of this adds up to be something so much more than a lock.
What’s in the box
Outside
4.59 in
2.59 in
Inside
7.03 in
2.78 in
Meet Nest x Yale Lock
2019 | Condential and Proprietary | Do not distribute
The key to connecting Nest Yale x Lock to the internet.
Meet Nest Connect
Nest Connect
Nest Connect is required to connect the Nest x
Yale Lock to your Wi-Fi network, so you can use
the Nest App to control your lock from anywhere.
It is a secure and reliable connection and only
communicates when necessary. Since Wi-Fi
technology can be a drain on baery products,
Connect allows a low energy signal to connect the
locks to the internet while saving baery. You can
also connect the Nest x Yale Lock to Wi-Fi through
a Nest Guard, if your customer already has one.
4.59 in
2.2 in 1.8 in
2019 | Condential and Proprietary | Do not distribute
●Optical
●Capacitive
touch
Weight Power requirements Baery life Operating temperature
Lights
Sensors
4 AA baeries included
(rechargeable baeries
not recommended)
●Outside range: –22° to 140°F
(–30° to 60°C)
●Baery range: 14° to 131°F
(–10° to 55°C)
●LED keypad
●Privacy Mode
indicator
Audio
Spoken ales with input
chime when lock code is
accepted
1 year
2 lb 4.2 oz
(1.03 kg)
Wireless
●802.15.4 (2.4GHz)
●Bluetooth Low Energy
(Inactive)
Weight Power requirements
Lights
Built-in rechargeable
lithium-ion baery
LED light
Power input
100-240 V∼50-60Hz 0.12A
0.98 oz (27.78 g)
Nest Connect
Operating temperature
32° to 104°F (0° to 40°C)
Indoor use only
Wireless
●Wi-Fi 802.11 b/g/n, 2.4GHz (WPA-PSK, WPA2-PSK, WEP
encryption suppoed)
●802.15.4 @ 2.4GHz
●Bluetooth Low Energy (BLE)
All the specs
Ceication
Ceied ANSI/BHMA
A156.36, Grade 2
2019 | Condential and Proprietary | Do not distribute
This is your comprehensive step-by-step guide to installing Nest x Yale Lock.
Don’t have time to read through the steps? Go to the Additional Resources section to watch
the installation video.
BEFORE YOU START
1. Impoant things to know
●Do not install the baeries before you’re told to by the installation instructions. If you
do, the lock may not be able to calibrate itself correctly, and have problems locking.
●You must install the Nest × Yale strike plate included with the lock. If you don’t, the
lock may jam. While the current strike plate may look the same, the Yale plate is
engineered to precisely t the new lock.
●You must close the door during the lock test as instructed. If you don’t, the lock won’t
calibrate itself to the customer’s door, and may jam. If the lock fails the test it will
automatically unlock.
●Keep the old lock handy, just in case.
2. Check that the lock will work with the door
●Before you begin installation, check that the door meets the
following requirements (most standard doors will). You can
use the template included in the installation manual or a
measuring tape.
●The door’s thickness must be between 1 ⅜ and 2 ¼ inches
thick.
●The lock hole center is either 2 ⅜ or 2 ¾ inches from the
edge of the door.
●If the door’s lock holes are out of these specs you can either
re-drill the holes aer you’ve removed the current lock
●Find handy PDFs for the Door Marker Templates here:
1 ⅜ to 1 ¾ inch thick doors
2 to 2 ¼ inch thick doors
Installation guide
Step by step
2019 | Condential and Proprietary | Do not distribute
1. What you’ll need
Everything you need to get staed installing the lock is in the box. Check that you have all the pas.
You’ll also need some tools:
●Phillips screwdriver or a power drill with Phillips bit
To connect the lock to the Nest app and the internet, you’ll need from the customer:
●A compatible phone or tablet (check the requirements here)
●Wi-Fi network password
INSTALL THE NEST X YALE LOCK
2. Remove the lock
●First, remove the current lock and strike plate if there is one already installed on the door. You may need
a dierent screwdriver or wrench to t the lock’s hardware. Re-drill the lock holes if needed.
●If the lock hole’s center isn’t either 2 3/8 or 2 3/4 inches from the edge of the door, use a 2 3/8 inch
spade drill bit and the template from the installation manual to reposition the holes. You may also need a
chisel to reposition the cutout for the latch plate.
3. Install the deadbolt
●Once the lock has been removed, it's time to install the Nest ×
Yale Lock’s deadbolt.
●Before you put it in your door, adjust the length to t the door
and make sure the bolt is retracted.
●Press t the bolt into the door as shown. Then use two of the
included screws to secure it.
Impoant: If you’re using a drill use a low torque seing to avoid
stripping the screw threads.
4. Install the strike plate
Impoant: The new strike plate included with the lock must be installed,
even if it looks the same as the current one. If not, the lock may jam.
●Remove the current strike plate and install the included strike plate
in the door frame.
●Make sure the hole in the plate will line up with the lock’s bolt
before you install it. If not, adjust the cutout for the plate with a
chisel.
Note: You can choose either the sho screws for easier installation with a
screwdriver or the long screws for extra security.
2019 | Condential and Proprietary | Do not distribute
5. Install the keypad
●Now you’ll install the keypad on the outside of the
door.
Impoant: Double check that the deadbolt is fully
retracted and that the latch hole is horizontal before
continuing.
●Run the cable through the lock hole. Then press to
t the keypad into the hole.
Note: Make sure you hold the keypad in the door as it is
loose and may fall out.
6. Install the mounting plate
●Pull the mounting plate o the back of the lock. Then remove the baery cover with the included
key.
●Inse the key into the hole at the top of the lock and press down. Pull the cover straight o.
2019 | Condential and Proprietary | Do not distribute
●Run the lock’s cable through the hole in
the mounting plate and press the
mounting plate pins through the holes
in the deadbolt. Then, use the bolts
that are the right length for the door to
secure the mounting plate.
●Before you fully tighten them, make
sure the keypad and plate are square to
the door. Use a bubble level if needed.
7. Install the lock
●Plug the cable to the connector on the lock. It can only be plugged in one way. Look for a small tab to align
it correctly. Then route the cable behind the cable hooks to hold it in place.
●Guide the spindle through the hole and hook the lock onto the boom of the mounting plate. Press the
lock rmly onto the plate. It will snap into place.
Impoant: Make sure the lock’s thumb turn is pointed veically and the bolt is fully retracted before you aach
the lock to the plate.
●Use the two small black bolts to screw the lock into the mounting plate. You can nd the holes for the bolts
in the baery compament of the lock.
2019 | Condential and Proprietary | Do not distribute
1. Test the lock
Now test that the lock works with the door both open and closed.
With the door open:
●Turn the thumb turn and make sure the bolt fully extends.
●Turn the thumb turn so the bolt is retracted.
With the door closed:
●Turn the thumb turn to lock the door.
If you feel resistance, or the bolt doesn’t extend fully, remove the lock
and re-check the deadbolt and lock installation.
TEST AND SET UP THE LOCK
2. Install the baeries
Impoant: Close the door but leave it unlocked while you install the baeries. If it isn’t, the lock will not be able to
test and calibrate itself to your door correctly.
●Inse the included AA baeries into the baery compament.
●The lock will turn on and you’ll hear the Nest greeting.
Don’t put the baery cover on yet. You’ll need to scan the code in the baery compament to connect to the
Nest app.
Note: If the lock fails the calibration test, reset it to defaults, and follow the steps for creating a master passcode and
connecting it to the app again.
3. Create a master passcode
●You’ll need to create a temporary master passcode on the lock before you can connect the lock to the
customer’s Nest app.
●Once you’ve connected the lock to their account on the app, you won’t need the master passcode anymore.
●Touch your palm to the keypad or press the Yale logo to wake up the lock. The lock will tell you what to do.
4. Calibrate the bolt/lock
●The lock will ask you to close the door so it can calibrate itself. If the lock detects an issue (such as a jam) it
will automatically unlock.
< Home
Table des matières
