golmar N3301 Manuel utilisateur
4
MOUNTING CONFIGURATIONS
*
( )
*
( ) For more information, see the TCODE/CA NEXA user manual (code 50123681)
https://doc.golmar.es/search/manual/50123681
NEXA audio and video
door entry system
Code 50123681 TN3301 REV.0 162
Golmar reserves the right to make any modifications without prior notice.
QUICK GUIDE
www.AlphaCommunications.com 1-800-666-4800
Sistemas de comunicación S.A.
Access control module
NEXA AUDIO AND VIDEO DOOR ENTRY SYSTEM - ACCESS CONTROL MODULE
N3301
access control module
SECSEC
~~ ~~
PRIPRI
~~ ~~
MainMain
12VAC
transformer
12VAC
transformer
(1)
(1)
C2NC1 NC2
CN1
P
~ ~
C1NA1 NA2 PL1 PL2
-
PL2
PL1
Va.c
Va.c
WIRING DIAGRAMS
*
( )
Use the varistor supplied with the N3301 module when using an AC lock release directly
on the terminals of the lock release.
(1)
The coded panel with display is configured by adding a display to the previous configuration,
thereby enabling the actions performed with the door panel to be viewed. This enables calls to be
made using the monitor code or the contacts residents list. It is also possible to gain access to the
building using the numeric code and view, on the door panel screen, the status of the actions
performed.
Coded panel with display:
In this operating mode, the SW1 DIP switch has no function.
N3301
access control module FA-Plus or FA-Plus/C
power supply unit
C2NC1 NC2
CN1
P
~ ~
SEC
+
-
PRI
~~
Red
C1NA1 NA2 PL1 PL2
-
Door panel with EL632/PLUS -
EL642/PLUS sound module
CN1
+
- -
+
CV1CV2
10
1
9
2
8
3
7
4
6
5
CN3
CN8
PL2
PL1
SEC
~~
PRI
~~
Main
SEC
~~
PRI
~~
Main
12VAC
transformer 12VAC
transformer
(1)
Va.c
(1)
Va.c
CN3
Standalone access control:
Access control combined with Nexa door panels:
50122310
2
*
( ) For more information, see the TCODE/CA NEXA user manual (code 50123681)
https://doc.golmar.es/search/manual/50123681
3
MOUNTING CONFIGURATIONS
*
( )
*
( ) For more information, see the TCODE/CA NEXA user manual (code 50123681)
https://doc.golmar.es/search/manual/50123681
SAFETY PRECAUTIONS
-Always disconnectthepowersupply before installing or making modifications tothe devices.
-The fitting and handling ofthese devices mustbe carried out by .authorizedpersonnel
- The wiring must run at least .40 cm away from any other wiring
-On the power supply unit:
wDo not overtighten the screws on the connector.
wInstall the power supply unit in a dry and protected place free from the risk of water leaks or sprays.
wAvoid locations that are humid, dusty or near heat sources.
wEnsure that the air vents are free from obstruction so that air can circulate freely.
wTo avoid damage, the power supply unit must be firmly secured in place.
wTo prevent electric shock, do not remove the cover or handle the wiring connected to the terminals.
-Coded module and access control.
-Can be combined with “Nexa Modular”and “Inox Modular”door panels.
-Configuration programmable using a numeric keypad, PC or tablet.
-Residents list with up to 1,990 contacts depending on setup.
-Status LEDs and tones.
CHARACTERISTICS
*
( )
MODULE DESCRIPTION
*
( )
a
b
c
d
e
f
g
h
i
j
k
a. Front
b. Green LED
c. Red LED
d. Numeric keypad
e. Key button
f. Cancel button
g. Back
h. SW1 DIP switch
i. JP1 tamper jumper
j. Connection block
k. Nexa Bus connectors
:Power input (Do not use when connecting the Nexa Bus link hose)
:Normally open output relay 1.
Common relay 1.
:Normally closed output relay 1.
:Normally open output relay 2.
:Common relay 2.
:Normally closed output relay 2.
:Panic output.
: Negative.
:Input for exterior button relay 1.
:Input for exterior button relay 2.
~ ~
NA1
C1
NC1
NA2
C2
NC2
P
-
PL1
PL2
Standalone access control:
The standalone access control enables access to the building by entering a numeric code using
the N3301 module.
Access control combined with Nexa door panels:
Configuring access control with call buttons enables users to make calls to apartments using
the call buttons and to gain access to the building by entering a numeric code into the N3301
module.
Coded panel without display:
The coded door panel enables calls to be made to apartments by entering the monitor code
and access to be gained to the building by entering a numeric code into the N3301 module.
Use to reset the special installer PIN to the factory code.
Proceed as follows: Set DIP switch 1 to ON. The module will emit 2 beeps
and the green LED on the front will light up for 1 second. Then set the DIP
switch to OFF (the code is now the one assigned at the factory). If the
access control module was locked during this process, the special unlock
PIN will also be reset to the factory code.
Set DIP switch 2 to OFF to configure the door panel as a standalone module.
Use to reset the special installer PIN to the factory code.
Proceed as follows: Set DIP switch 1 to ON. The module will emit 2 beeps
and the green LED on the front will light up for 1 second. Then set the DIP
switch to OFF (the code is now the one assigned at the factory). If the
access control module was locked during this process, the special unlock
PIN will also be reset to the factory code.
Set DIP switch 2 to OFF to configure the door panel as a standalone module.
Use to reset the special installer PIN to the factory code.
Proceed as follows: Set DIP switch 1 to ON. The module will emit 2 beeps
and the green LED on the front will light up for 1 second. Then set the DIP
switch to OFF (the code is now the one assigned at the factory). If the
access control module was locked during this process, the special unlock
PIN will also be reset to the factory code.
Set DIP switch 2 to ON to configure the door panel as a coded door panel.
NEXA AUDIO AND VIDEO DOOR ENTRY SYSTEM - ACCESS CONTROL MODULE NEXA AUDIO AND VIDEO DOOR ENTRY SYSTEM - ACCESS CONTROL MODULE
Table des matières
Autres manuels golmar Panneau de contrôle
