GLP YPOC PRO 250 Manuel utilisateur

Instruction Manual

from software version 1.0

(instruction version 1.05)

e-mail: [email protected]

Internet: http://www.glp.de

GLP German Light Products GmbH (instruction version 1.05) 2

Notes:

GLP German Light Products GmbH (instruction version 1.05) 3

Table of contents

1Description of Device..............................................................................................5

1.1 Safety Instructions ............................................................................................6

2Preparation and Installation ...................................................................................7

2.1 Mounting...........................................................................................................7

2.1.1 Clamps ...................................................................................................7

2.1.2 Mounting plate........................................................................................8

2.2 Secure the Y

O .............................................................................8

2.3 Connections......................................................................................................9

2.3.1 Power supply..........................................................................................9

2.3.2 DMX .......................................................................................................9

2.4 Fuse..................................................................................................................9

3The Menu Field ......................................................................................................10

3.1 Adjust the DMX- Address (D001)..................................................................11

3.2 The Test Program (TEST).............................................................................11

3.3 The Audio Program (AUDI)...........................................................................11

3.4 Lamp On/Off (LAMP) .....................................................................................12

3.5 Reset (RESE) ................................................................................................12

3.6 Operating time of lamp and unit (TIME)........................................................12

3.7 Invert Pan Movement (RPAN)........................................................................12

3.8 Invert Tilt Movement (RTLT) .........................................................................13

3.9 Special Functions (SPEC)..............................................................................13

3.9.1 Manual Drive (MANU) ..........................................................................13

3.9.2 Lamp On automatically (LAAU)...........................................................13

3.9.3 Lamp Off via DMX (DLOF) ..................................................................14

3.9.4 DMX Input (DMXI) ..............................................................................14

3.9.5 Display (DISP)....................................................................................15

3.9.6 Fixture Temperature (TEMP)...............................................................15

3.9.7 Fan Control (FANS).............................................................................15

3.9.8 Adjustments and Calibrations (ADJU).................................................16

3.9.9 Default Settings (DFSE) ......................................................................16

3.9.10 Feedback (FEED)................................................................................17

3.9.11 Correction of faults (EFLG) .................................................................17

3.10 Error and Information Messages.....................................................................17

GLP German Light Products GmbH (instruction version 1.05) 4

4DMX Channel Selection (DMX Protocol) .............................................................18

5Changing the Lamp...............................................................................................22

5.1 Safety Regulations..........................................................................................22

5.2 Realize the Lamp Change ..............................................................................22

5.3 Lamp adjustment ............................................................................................23

6Changing a Gobo ..................................................................................................24

6.1 Safety Regulations..........................................................................................24

6.2 Realize the Gobo Change ..............................................................................24

7Maintenance and Cleaning the Y

O..................................................25

7.1 Safety Regulations..........................................................................................25

7.2 Circumference and Interval (rule-of-thumb) ....................................................25

7.3 Cleaning the Optical System ..........................................................................26

8Technical Specification ........................................................................................27

9Index.......................................................................................................................28

Annexes........................................................................................................................29

A) Chassis Ground..................................................................................................29

B) Dimensions and Views .......................................................................................29

GLP German Light Products GmbH (instruction version 1.05) 5

1 Description of Device

1. Moving Head

2. Carrying handles

3. Base casing

4. Arm

5. Up- button

6. Down- button

7. Enter- button

8. Mode- button

9. LED- Display

10.Software- Update

connector

11.Microphone- intensity

12.DMX- Input

13.DMX- Output

14.Power ON/OFF

15. Micro fuse

16.Fan (air inlet)

MaxMin

DMX IN DMX OUT

Software

1. Gr oun d

2. Da

a -

3. Da

a +

POWE

210V~

230V~

250V~

50Hz

60Hz

Power

FUSE:

T3.1 5A

MP:

MSD 25 0W

Seria

ber:

Fuse

Mic

1 2

PUSH

FUS

MODE ENTER UPDOWN

MODE ENTE

UPDOWN

8 7 6 5

12 13 14

GLP German Light Products GmbH (instruction version 1.05) 6

1.1 Safety Instructions

The

is a High-Tech Product. To guarantee a

smooth operation, it is necessary to keep following rules.

The manufacturer of this device will not take responsibility of

damages through disregard of the information in this manual.

Warranty adjustments will be cancelled.

1. Make sure before putting into operation, that the fan and the air inlets are

clean and not blocked by anything.

2. Attention: Don’t touch the device during the operation. This can cause injuries

or damages.

3. Unplug the

from the AC outlet before any service.

4. It is necessary to wait at least 30 minutes after disconnecting the AC before

you open the Y

O. Please do not touch the bulb of the lamp if you

are not absolutely sure it is cold. -- Danger of BURNING --

5. Never look directly into the beam of the lamp. You risk injury of your retina and

blindness.

6. Pay attention of the maximum lamp operation time. You have to change it if

the lamp shows any deformations or damages. The same is with all glass

components, color filters, lenses and mirrors.

7. To allow a secure operation, follow also the Installation guide described in

chapter 2. Operating the Y

without suited safety aids like Safety

cables or clamps/hooks can increase the risk of an accident.

8. The installation should be done by qualified staff only. You need to pay

attention to the common rules of technology that are not explicit mentioned in

this manual.

9. Use only original spare parts. Any structural modification will cancel all

warranty adjustments.

LASERSTRAHLUNG

NICHT IN DEN STRAHL BLICKEN

LASER KLASSE 3R

NACH DIN-EN 60825-1/11:2001

P 5mW; = 635-650 nm

Attention: Laser of class 3R may

injure your retina after a short resi-

dence time even without any optical

instrument. Avoid any direct ex-

posure of your eyes!

GLP German Light Products GmbH (instruction version 1.05) 7

2 Preparation and Installation

2.1 Mounting

The Y

is fully operational whether it hangs or is mounted to the wall.

It can also be operated while standing on the floor. Keep a safety distance of 0.5

m towards any easy inflammable materials (decoration etc.). Install a safety wire

that can hold at least 10 times the weight of the fixture. Never use the carrying

handles for secondary attachment.

Pay attention to the regulations of: BGV C1 (former VBG 70)

and DIN VDE 0711-217. Regulations of show laser BGV B2

(11.2001), E DIN 56912 part 6, DIN-EN 60825 part 1+2.

The installation should be done by qualified staff only.

2.1.1 Clamps

There are two major possibilities to mount the Y

O. A so called

Camlock system or direct mounting of clamps. In both cases you have to

regard a sufficient stability of the system. For installation instructions please

see also printing on the backside of the case.

GLP German Light Products GmbH (instruction version 1.05) 8

90°

106.0

a) Camlock system: This system allows you a fast and efficient setup of

clamps. Attach the two camlocks to the designated position C1 and C2

on the backside of the case and close the locks by turning them 90°.

Verify the secure fit of the camlock

system. The clamps themselves are

directly attached permanently on the

camlocks.

b) Use two clamps direct on the backside of the Y

Oto mount

the unit on a truss (each two opposite threads A1/A2 or A3/A4 max.

M10x20).

4x M10x20mm

4x Camlock

106.0

196.0

240.0

A3 A4

196.0

26.0

333.0

240.0

A3 A4

2.1.2 Mounting plate (optional)

For a permanent installation of the Y

Oyou can use an

optional mounting plate to fix the unit directly onto a wall. The plate is

screwed on the system at the positions B1/B2 with screws M6x20.

2.2 Secure the

Regardless of the rigging of the Y

you have to use a stipulated

safety wire. Therefore you have to thread to safety wire through to two provided

holes on the backside of the fixture and connect it with the truss-support. Pay

attention to a safe and proper fastening.

GLP German Light Products GmbH (instruction version 1.05) 9

2.3 Connections

2.3.1 Power supply

230 Volt, two-pin earthed plug 50 Hz,

Connected load 500W <=> 2,2 A (blind current compensated).

2.3.2 DMX

DMX 512 Standard input/output. See also printing on the case for the right

pin assignment.

[+] = Pin 3 / [-] = Pin 2 / [Ground] = Pin 1

The DMX- Addressing starts at the DMX- Address [001].

2.4 Fuse

The Y

Oelectronic system is protected by a 5x20 mm micro-fuse

T3,15A.

Please see also the printing on the Y

casing for more details.

Attention:

• Disconnect AC mains supply before changing a fuse!

• Use only the original declared fuse type!

GLP German Light Products GmbH (instruction version 1.05) 10

3 The Menu Field

You’ll find the control board on the side part of the base. It allows you to

make all necessary adjustments of the Y

.With the Mode-key

you get into the main menu. Afterwards you can navigate through the menu

with the Up/Down-keys. Push the Enter-key to get in the next menu level

or to confirm your settings. Make them and set functions ON/OFF with the

Up/Down-keys. Confirm and save it with the Enter-key (the display shows

OK). Push the Mode-key to cancel the entry and go back to the main menu.

MODE ENTER UPDOWN

RUPD

LED-Displa

Mode-Taste Enter-Taste Down-Taste Up-Taste

ÅMODE - ENTER Æ

Level 1 Level 2 Level 3 Remark

D001 Define the DMX start address

TEST Test program of all functions

AUDI ASLW Self-running audio program (slow)

AFST Self-running audio program (fast)

MSTR Master for the audio program

SVPT Basic position for the audio program

SIZE Size for the audio program (NORM-BIG-MIDL-SMAL)

LAMP Switch on/of the lamp direct at the Y

RESE Reset

ÅDOWN - UP Æ

TIME POWR Running time of the fixture (no destructible)

LA1 Running time of the lamp (erasable)

LA2 Running time of the lamp (no destructible)

RPAN Reverse Pan-direction

RTLT Reverse Tilt-direction

SPEC MANU Manual drive of all device functions

LAAU Automatic lamp start

DLOF Switch off lamp via DMX

DMXI Reed out actual DMX-values

DISP D ON Display On/Off

REV Twist the display

TEMP Reed out internal temperature

FANS HIGH Maximum cooling fan velocity

REG Automatic cooling fan control

LOOF Low cooling fan speed Ælamp off

LOHI Low cooling fan speed Æautomatic

ADJU CODE

xxxx

Use the code for entering the calibration menu (for authorized

persons only)

COLO Calibration of the color wheel

GOB1 Calibration of the gobo wheel 2

GOB2 Calibration of the gobo wheel 2

SHTR Calibration of the shutter

PRIS Calibration of the prism wheel

ÅDOWN - UP Æ

IRIS Calibration of the iris

POFS Calibration of the Pan-Offsets

TOFS Calibration of the Tilt-Offsets

CLRE Settings in the internal memory (super-user only)

ARES Adjust Reset (wheels stand still after the reset)

VTIL Software version Tilt-board

VTR1 Software version driver board 1

VTR2 Software version driver board 2

VTR3 Software version driver board 3

DFSE Call on the default function values

FEED Pan/Tilt feedback (error correction) On/Off

EFLG Correction of faults

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels GLP Mettre en lumière

GLP

GLP Fusion EXO Spot 30 Manuel utilisateur

Manuels Mettre en lumière populaires d'autres marques

Guangzhou Yinhe Lighting&Sound Equipment Factory

Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 Manuel utilisateur

LIVARNO home

LIVARNO home 375304 2101 Instructions originales

Cameo

Cameo CLQS40WW Manuel utilisateur

Leviton

Leviton Ellipsoid 5/50 Manuel utilisateur

Monacor

Monacor img Stage Line PARL-56PDX/CR Manuel utilisateur

Vector

Vector SL3AKV Manuel utilisateur

Quantum

Quantum Q262 Manuel d'exploitation

Philips

Philips Vari-lite VL3015LT Manuel utilisateur

EUROSPOT

EUROSPOT C51 Manuel utilisateur

DTS

DTS MINI BRICK ARC Manuel utilisateur

Federal Signal Corporation

Federal Signal Corporation VISIBEAM II Manuel

ACME

ACME LED-MS350B Manuel utilisateur

EuroLite

EuroLite Akku flat light 1 Manuel utilisateur

Commercial Electric

Commercial Electric SPTM-1401 Manuel utilisateur

Vision & Control

Vision & Control SLB-500-W5K7-P-SL Manuel utilisateur

Teknik

Teknik FLEXI Manuel utilisateur

Craftsman

Craftsman CMXLSB10 Manuel utilisateur

EuroLite

EuroLite LED SLS-144 UV Floor Spot Manuel utilisateur