Glensound Dante BEATRICE P1 Manuel utilisateur
BEATRICE P1
& P2
Phone handset Dante network intercom
PRODUCT DETAILS
THE DESIGN BUILDINGS, 6 BROOKS PLACE, MAIDSTONE, KENT, ME14 1HE. UK.
TEL: +44 (0) 1622 753662
Visit our Website at www.glensound.com
Page 2of 27
Glensound Electronics Ltd
Thank you for choosing a new Glensound product.
All rights reserved.
Information contained in this manual is subject to change without notice, if
in doubt please contact us for the latest product information.
If you need any help with the product then we can be contacted at:
Glensound Electronics Ltd
The Design Buildings
1 –6 Brooks Place
Maidstone
Kent
ME14 1HE
United Kingdom
Telephone: +44 (0) 1622 753662
EMAIL ADDRESSES
General enquires: sales@glensound.com
Technical enquires: techinfo@glensound.com
Sales enquires: sales@glensound.com
Page 3of 27
PRODUCT WARRANTY
All equipment is fully tested before dispatch and carefully designed to
provide you with trouble free use for many years.
We have a policy of supporting products for as long as possible and
guarantee to be able to support your product for a minimum of 10 years.
For a period of one year after the goods have been despatched the
Company will guarantee the goods against any defect developing after
proper use providing such defects arise solely from faulty materials or
workmanship and that the Customer shall return the goods to the
Company’s works or their local dealer.
All non-wear parts are guaranteed for 2 years after despatch and any
defect developing after proper use from faulty materials or workmanship
will be repaired under this warranty providing the Customer returns the
goods to the Company's works or their local dealer.
Page 4of 27
EU DECLARATION OF CONFORMITY
GS-BEATRICE P1 & P2
Phone handset Dante intercom
This declaration of conformity is issued under the sole responsibility of
the manufacturer.
This equipment is manufactured by Glensound Electronics Ltd of Brooks
Place Maidstone Kent ME14 1HE is marked and conforms to the
following Union harmonisation legislation:
Emissions: BS EN55032:2015
Immunity: BS EN55035:2017
Signed for and on behalf of Glensound Electronics Ltd.
Gavin Davis, Managing Director
Maidstone, Kent, England
Date: 03/09/2019
Page 5of 27
RoHS DIRECTIVE
RoHS 2 Directive 2011/65/EU restricts the use of the hazardous
substances listed below in electrical and electronic equipment.
This product conforms to the above directive and for these purposes, the
maximum concentration values of the restricted substances by weight in
homogenous materials are:
Lead
0.1%
Mercury
0.1%
Hexavalent Chromium
0.1%
Polybrominated Biphenyls
0.1%
Polybrominated Diphenyl
Ethers
0.1%
Cadmium
0.01%
Page 6of 27
WASTE ELECTRICAL AND ELECTRONIC
EQUIPMENT REGULATIONS 2006 (WEEE)
Glensound Electronics Ltd is registered for business to business sales of
WEEE in the UK our registration number is:
WEE/JJ0074UR
Page 7of 27
GLENSOUND BEATRICE P1 & P2
HANDBOOK CONTENTS
Description Issue 1 Page No.
Contents
PRODUCT WARRANTY ........................................................................................................................3
EU DECLARATION OF CONFORMITY.................................................................................................4
RoHS DIRECTIVE ..................................................................................................................................5
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT REGULATIONS 2006 (WEEE).................6
HANDBOOK CONTENTS......................................................................................................................7
OVERVIEW.............................................................................................................................................8
P1 & P2 REAR PANEL LAYOUT ..........................................................................................................9
P1 FRONT PANEL LAYOUT ...............................................................................................................10
CONFIG MODE ....................................................................................................................................11
RESET TO FACTORY DEFAULT SETTINGS.....................................................................................12
CALLING OTHER BEATRICE DEVICES ............................................................................................12
AUDIO BLOCK DIAGRAM (analogue representation of digital circuits).......................................13
Audio Circuits TO and FROM Dante/ AES67....................................................................................13
CONNECTING THE BEATRICE UNITS TO A DANTE NETWORK....................................................14
Getting Dante Controller....................................................................................................................14
Connecting Beatrice device to the network.......................................................................................14
Audio Over IP Network......................................................................................................................14
Running Dante Controller..................................................................................................................15
Dante Controller TIP..........................................................................................................................15
Device not showing up in Dante Controller .......................................................................................16
AES67 MODE.......................................................................................................................................17
Turning On AES67 Mode ..................................................................................................................17
Sending AES67 Audio.......................................................................................................................18
Receiving AES67 Audio ....................................................................................................................19
AES67 Restrictions............................................................................................................................19
UPDATING FIRMWARE.......................................................................................................................20
Equipment needed ............................................................................................................................20
Instructions ........................................................................................................................................20
UPDATING THE ULTIMO CHIPSET....................................................................................................26
Finding Out Current Installed Version ...............................................................................................26
Finding Out What The Latest Available Version Is............................................................................26
Updating the device...........................................................................................................................26
WIRING INFORMATION ......................................................................................................................27
Headset Wiring..................................................................................................................................27
Page 8of 27
OVERVIEW
The BEATRICE range of IP intercoms was designed for broadcast, theatre and
professional audio applications.
Our Beatrice intercom system utilises the reliable and proven DanteTM network audio
transmission protocol to allow real time distribution of uncompressed audio across
standard networks. As such the BEATRICE P1 & P2 units are also fully compatible
with other manufacturers’ equipment using the DanteTM protocol. The Beatrice P1 &
P2 are also both AES67 compliant.
All units in the system are designed to be very easy to use for the operator and
simple to setup for the technician. They includes all the basic functionality required
for small intercom systems and none of the overly complex installation requirements
normally associated with large systems.
The name Beatrice was chosen for our intercom range as she was the love of Dante
Alighieri:
‘Dante had fallen in love with another, Beatrice Portinari (known as Bice),
whom he first met when he was only nine.’ Source Wikipedia.
Page 9of 27
P1 & P2 REAR PANEL LAYOUT
1. Encoder
This encoder is used to control parameters for the config settings of the
device.
2. Status LEDs
These LEDs indicate which setting the encoder is adjusting whilst changing
config levels.
3. RJ45 Connector
This is a 100M/bit standard IP network connection. The amber status LED
flashes to show when data is being correctly communicated with the attached
switch. The green LED illuminate to show PoE power is received. The PoE
source can be a mid-span source or a network switch with PoE.
4. Update switch
Holding down this switch for 11 seconds will reset the device to factory default
settings.
5. USB connector
Allows the local device firmware to be updated.
1. Encoder
2. Status LEDS
3. RJ45 Connector
4. UPDATE Switch
5. USB Connector
Page 10 of 27
P1 FRONT PANEL LAYOUT
1. Handset
The handset connects to the device via the 4P4C RJ connector on the front of
the device. Please refer to the end of the manual for wiring information.
When the handset is picked up the microphone audio is sent to the Dante
network and muted when placed back. Picking the handset up will stop the
device ringing when receiving a call. On the P2 you can receive calls from
both channels when talking to a channel.
2. Incoming call LED
The Call LED indicates the presence of an incoming audio from the Dante
network by flashing when the audio goes above a threshold of -30dBFS. The
Call LED will flash for a few seconds upon receiving a call.
3. Call switch
This switch is used to send a call to the network output. Double press to send
the call. An audible beep will sound from the sounder when a call is sent.
On the P2, these switches can be toggled to choose which or both Dante
channels you wish to speak to. The switch will illuminate to show that you are
talking to that channel.
4. Present LED
This LED will illuminate to show audio presence from the Dante network.
3. Incoming call LED
4. Handset
2. Call switch
1. Present LED
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Glensound Système d'interphone
