GIULIANO PRESS ARM Manuel utilisateur

Instructions for

mounting/removing

tyres with HELP and

PRESS ARM

ed. 11/2005 cod. 3015761

Preliminary remarks: HELP and PRESS ARM are accessories fit to be installed on

S222 – S225 – S224 – S231 – (S232).

PRESS ARM only can be installed on S112F.

Their combined use is essential with “zero pressure” tyres.

The use of PRESS ARM is essential on low-profile tyres (from /45 to /30).

They are recommended on any kind of tyres.

Between the two devices, the PRESS ARM is the more versatile one.

Ty re

REMOVAL

Set the wheel on turntable, pressing tyre from over the jaws, and

lock the rim paying attention it doesn’t slip out of the jaws (this

operation might turn out difficult or even impossible).

Use the PRESS ARM to push the wheel downward so making its

clamping easier.

Correct clamping

Manual procedure

Assisted procedure

In case the rim to be removed has an “overturned” groove, use the

accessory shown above (WHEEL PRESSING CONE, part no.

9214251) to keep the tyre pushed on the jaws, so locking the rim.

In case the tyre bead slips back again into its seat, manually help

the tool positioning, acting a bit on the hexagonal arm (the

operation might turn out difficult or even impossible)

Manual procedure

Assisted procedure

HELP roller (if available) can be used for pushing the tyre in a way

to correctly set the tool on the rim without any effort.

PRESS ARM press pad can be used for pushing the tyre in a way

to correctly set the tool on the rim without any effort.

Assisted procedure

Use the PRESS ARM press pad to keep the tyre pushed while

inserting the lever between tyre and tool.

Push the tyre downwards, by hand, to let the bead lifting lever enter

the gap between tyre and tool (this operation might turn out difficult

or even impossible).

Manual procedure

Assisted procedure

Use the HELP roller (if available) to

push the tyre in a way to correctly

set the bead lifting lever between

tyre and tool.

To remove first bead from rim it is necessary

to push it downwards, at tool opposite side,

to position it at the rim groove level (this

operation might turn out difficult or even

impossible).

Manual procedure

Assisted procedure

Use the PRESS ARM disk to lift the tyre lower part from left side,

help yourselves by hand to also lift it from right side, in a way to

facilitate the insertion of the lever and complete detachment

operation.

Use the PRESS ARM press pad to push the tyre in a

way to bring the bead (tool opposite side) into the rim

groove and to make its detachment easier.

Manual procedure

Assisted procedure

If both devices are installed, use both disks to lift the tyre from both

right and left side.

If HELP is available, use its roller to lift the lower bead over tyre

edge to allow removal operation without lever.

The removed tyre

Assisted procedure

Use the HELP press pad (if available) to push the tyre in a way to

grease the rim inner side so facilitating the detachment.

Ce manuel convient aux modèles suivants

Autres manuels GIULIANO démonte-pneus

GIULIANO

GIULIANO S 561 Instructions de fonctionnement

GIULIANO

GIULIANO Crossage Guide de l'utilisateur

GIULIANO

GIULIANO G1 SPORT Manuel utilisateur

GIULIANO

GIULIANO S224 Document technique

GIULIANO

GIULIANO S 551 XL A Instructions de fonctionnement

GIULIANO

GIULIANO S 226 Manuel d'instructions

GIULIANO

GIULIANO S 560 Instructions de fonctionnement

GIULIANO

GIULIANO S 554 Instructions de fonctionnement

GIULIANO

GIULIANO S 551 XL A Instructions de fonctionnement

GIULIANO

GIULIANO S 557 Instructions de fonctionnement

Manuels démonte-pneus populaires d'autres marques

MW TOOLS

MW TOOLS BT200 Manuel utilisateur

Hunter

Hunter Maverick Series Manuel utilisateur

Corghi

Corghi BR2-C1E Manuel utilisateur

Snap-On

Snap-On EEWH311B Manuel utilisateur

TMG

TMG LC889NV Manuel utilisateur

JMP

JMP Fix Moto Schéma de câblage

Corghi

Corghi A 9222 HP TI Manuel utilisateur

foc.us

foc.us F640 Manuel utilisateur

Corghi

Corghi Artiglio Master 26 MI Manuel utilisateur

SICE

SICE S 52A Manuel utilisateur

Sealey

Sealey TC968.V2 Manuel utilisateur

Coats

Coats 80C Manuel utilisateur

HENNESSY INDUSTRIES

HENNESSY INDUSTRIES Coats Rim Clamp X-Model Series Manuel utilisateur

Draper

Draper 78612 Manuel utilisateur

Aston Global

Aston Global ATC-5800 Mode d’emploi

HENNESSY INDUSTRIES

HENNESSY INDUSTRIES Coats CHD-4730-4730W Manuel

Butler

Butler NAV11N Manuel utilisateur

Ranger

Ranger R76LT Manuel utilisateur