Gira Alarm Connect Manuel utilisateur

Quick Start Guide for the security system

Alarm Connect

QSG_security_system_Alarm_Connect_en.fm Seite 1 Donnerstag, 31. Januar 2019 7:45 07

Table of contents

Important terms related to the security system Alarm Connect ...................... 3

The operating and configuration mode .......................................................................................... 3

The operating mode ....................................................................................................................... 3

The configuration mode ................................................................................................................. 3

The security area ............................................................................................................................ 4

Internal alarm ( ) .......................................................................................................................... 4

External alarm ( ) ......................................................................................................................... 4

Set up a small security system Alarm Connect,

put into commissioning and test ..................................................................... 5

Prepare the alarm control unit Connect ......................................................................................... 5

Configuration in GPA ...................................................................................................................... 6

Put the wireless operation unit into commission ........................................................................... 8

Put the wireless magnetic contact into commission ..................................................................... 8

Test the system and devices 9

The security system Alarm Connect has been successfully

set up and tested. What's next? ...................................................................... 9

Deactivate devices ......................................................................................................................... 9

Create customer project.................................................................................................................. 9

The device list ................................................................................................. 10

Device list, Example .................................................................................................................... . 10

Device list, Template .................................................................................................................... 10

Quick start guide — Table of contents

QSG_security_system_Alarm_Connect_en.fm Seite 2 Donnerstag, 31. Januar 2019 7:45 07

Important terms related to the security system Alarm Connect

Below you will find information on how to quickly and easily set up and commission a project,

and how to perform a functionality test for the project, with at least three devices.

After a successful functionality test, the settings defined, as well as the devices set for the

customer project, can continue to be used.

In relation to the security system Alarm Connect, there are certain terms that are briefly

explained in advance.

The two main

modes in the alarm

control unit

Connect

Commissioning and configuration mode

The following two modes are important when using the alarm control unit Connect:

• Operating mode.

• Configuration mode.

Operating mode

In operating mode, messages (e.g. “Alarm device open”) are shown in the display and the safety

area can be switched to “internally or externally armed”, or can be disarmed.

Prerequisite for the operating mode: the housing cover is closed (position 0) or pushed up to

the first stop (position 1).

Configuration mode

In configuration mode, changes from the GPA can be saved to the alarm control unit memory

under “Project commissioning”. To do this, the alarm control unit must be connected to the

commissioning PC.

In addition, the test mode (in the GPA or on the wireless operating unit) can be activated.

Prerequisite for the configuration mode: The screws visible in position 1 and integrated into the

hinged cover have been loosened. The housing cover is removed (position 2)—only works with

previously-released locking screws—and the hinged cover of the battery compartment can be

opened.

Security system Alarm Connect

The security system Alarm Connect can only be commissioned with the GPA (Gira Project

Assistant) configuration software.

Detailed information on the security system Alarm Connect can be found in the system or in

the GPA online help section.

The GPA and the system description are available at www.gira.de/service/download.

LAN

Position 1

Position 0Position 0

Betriebsmodus = Position 0 & 1

LAN

Position 1

Position 0

Kongurationsmodus = Position 2

Position 2

Preliminary

information

Quick start guide — Preliminary information

QSG_security_system_Alarm_Connect_en.fm Seite 3 Donnerstag, 31. Januar 2019 7:45 07

What is a security

area?

The security area

The Gira security system Alarm Connect has a maximum of four security areas.

One feature of the security area is the monitoring of completed buildings or areas, each of

which can be separately armed or disarmed. Unauthorised intrusion into an armed security area

triggers an alarm.

Example: An object with two independent security areas (each security area has a separate

entrance). The alarm control unit Connect is located in Security area 1.

For the application described in this Quick Start Guide, only the main security area is required.

What does

“Activated

internally” mean?

"Activated internally"( )?

“Internally activated” means that a security area is armed and people are in the security area.

This corresponds to the so-called perimeter monitoring.

Internal activation takes place, for example, on the wireless operating unit within the security

area.

Devices with the setting “active when externally armed” (e.g. wireless motion detectors) do not

trigger an alarm when a detected event occurs.

Devices with the setting “active when internally and externally armed” (e.g. wireless magnetic

contact) trigger an alarm when a detected event occurs.

What does

“Externally

activated” mean?

“Externally activated” ( )?

“Externally activated” means that a security area is armed and that no one is in the security

area. This corresponds to the so-called indoor and perimeter monitoring.

All devices with the setting “active when internally and externally armed” or “active when

externally armed” trigger an alarm when a detected event occurs.

Security area 1, (main security area):

Main apartment with separate entrance

Security area 2

Office with separate entrance

Security area in the GPA project

Note the following:

• Alarm control unit Connect in the GPA is always situated in the main security area (Security

area 1).

• One wireless operating unit is required per security area used.

• Always assign the wireless outdoor siren (optional) to the main security area.

1 2

Quick start guide — The security area

QSG_security_system_Alarm_Connect_en.fm Seite 4 Donnerstag, 31. Januar 2019 7:45 07

I want to quickly

test the security

system Alarm

Connect. What do

I need to do?

Set up, put into commission and test a small security system

Alarm Connect

For quick set-up and functional testing, the security system Alarm Connect has the following

three devices:

• 1 x alarm control unit Connect (mandatory).

• 1 x wireless operating unit (mandatory).

• At least one alarm detector (here: 1 x wireless magnetic contact as a trigger).

Here goes! Prepare the alarm control unit Connect

1. Unpack the alarm control unit Connect.

2. Push the housing cover up until the screws that are integrated into the hinged cover of the

battery compartment are exposed and the housing cover is noticeably blocked. The housing

cover is now in Position 1.

3. Loosen both screws and remove the housing cover. The hinged cover on the battery

compartment can be opened. The housing cover can only be pushed up beyond Position 1

if the two screws were loosened before! The alarm control unit Connect is only in

configuration mode once the housing cover has been removed! Do not reinsert and slide

down the housing cover.

4. Connect the battery pack and the mains voltage.

5. Connect the commissioning PC to the alarm control unit Connect via Ethernet cable:

• One-to-one connection via the LAN port of the alarm control unit Connect or

• Via the local network.

Configuration mode of the alarm control unit Connect

For the configuration mode of the alarm control unit Connect, the following applies:

• All security areas are disarmed.

• The internal battery pack and the mains voltage are connected.

• The housing cover is removed.

LAN

Position 1

Position 0Position 0

Betriebsmodus = Position 0 & 1

LAN

Position 1

Position 0

Kongurationsmodus = Position 2

Position 2

LAN

AMT

TEL

A2B2

LAN

AC 230 V

LAN

GiraContr. panel

MAC-Adr.LAN

XX:XX:XX:XX:XX:XX

MAC-Adr.WLAN

XX:XX:XX:XX:XX:XX

KNXSecure 1

FDSK1

AAEBBI-IACHKM-G0SW2M-

SUESVI-3K1PFN-FHZVQF

RS485

12V GND A1 B1

RS485

12V GND A2 B2

RS485

12V GND A3 B3

RS485

12V GND A4 B4

INPUTS

12V GND IN1 IN1

OUTPUTS

12V GND OUT1 OUT2

Bereich

Linie

TLN-Nr.

IPAdr.

Ort/Notiz

Gira,Dahlienstraße

42477Radevormwald

Germany

IP S

GPA

Ahnjy9eWVgNt+bgz

GPA

Akku

Quick start guide — Setting up the security system

QSG_security_system_Alarm_Connect_en.fm Seite 5 Donnerstag, 31. Januar 2019 7:45 07

Setting up the

project

Configuration in GPA

1. Download and install the most current version of GPA from Gira's download area.

2. Open GPA and create a new project (in the example “Sample project”).

3. Select “Alarm system” under project scope.

4. Create a building structure (in the example: one storey, one room).

5. The alarm control unit Connect is displayed under “New devices found” in the device library.

6. The GPA might request a firmware update from the alarm control unit. The GPA

automatically detects if an updated firmware version is available.

7. Locate the alarm control unit Connect (by dragging and dropping into the room).

8. The alarm control unit Connect is disabled (visible by the symbol). Enter the initial password

and unlock the alarm control unit Connect.

What is the initial

device password?

Battery capacity and firmware update

A firmware update works only with sufficient battery capacity.

When delivered, the capacity of the battery pack is insufficient for a firmware update.

The GPA aborts the firmware update automatically and without warning when insufficient

battery capacity is detected! The alarm control unit Connect should be connected to the mains

voltage for at least two hours if the battery pack is connected. Firmware updates can then be

carried out successfully.

Library

Storey

Features

General

Name

Storey

Category

Security area

Security area 1

Components

Hardware ID

01-00001

Alerting

Device with gateway function

Door chime

Building

Devices

Wireless magnetic contact

New devices found

Assigned devices

Device catalog

Gira Alarm System 2.0.7

Available components

HWS

Gira Alarm System 2.0.7

Wireless glass-breakage sensor, surface-mounted

Wireless I/O module

I/O

Wireless motion detector with camera

Wireless motion detector

Wireless indoor siren

Wireless outdoor siren

Wireless technical contact

Wireless operating unit

Wireless hand-held transmitters

Wireless glass-breakage sensor, ﬂush-mounted

Library

Room

Wireless

magnetic cont...

Wireless

operating unit

Triggering contact

Only use internal magnetic contact...

Internal magnetic contact and external...

Use external contact only

Device is armed for

Internally and externally armed

Externally armed

Gira

security sstem

Commissioning

Inbetriebnahme

Inbetriebnahme starten

Gira Sicherheitssystem...

Online

IP: 192.168.111.111

Appliaktionsdaten löschen

Projektkopie auf Gerät sichern

Letzte Inbetriebnahme

Start commissioning

Quick start guide — Configuration in GPA

QSG_security_system_Alarm_Connect_en.fm Seite 7 Donnerstag, 31. Januar 2019 7:45 07

Put the device into

commission

Put the wireless operating unit into commission

1. Insert the batteries into the battery compartment of the wireless operating unit (observe

polarity!). The wireless operating unit is automatically recognised due to the hardware ID

entered in the GPA.

2. Wait for the initialisation phase. This can take up to five minutes. After successful

initialisation, the following appears in the display of the wireless operating unit:

If the initialisation is unsuccessful, please repeat step 1.

In addition, compare the hardware ID in the GPA with the hardware ID on the

device label. Note that any change in the GPA requires a re-commissioning of the

project.

Put the wireless magnetic contact into commission

1. Lower the sliding cover of the wireless magnetic contact to better recognise the LED status.

2. Pull out the protective strips of the batteries on the wireless magnetic contact.

3. Wait for the initialisation phase. The LED status flashes red/green alternately for approx.

ten seconds and then turns off.

After successful initialisation, the following appears in the display of the wireless operating

unit:

If the initialisation is unsuccessful, please remove the batteries and insert them

again. In addition, compare the hardware ID in the GPA with the hardware ID on the

device label.

Display lighting

When not in use, the display lighting automatically goes off after approx. 30 s.

By pressing the OK button, the display lighting is switched on again.

Symbol Meaning Cause

Symbol

blinks

Fault The housing cover of the alarm control unit is open and

the wireless operating unit is not attached to the mounting

frame.

For the functionality test, the cause does not have to be

eliminated.

Symbol Meaning Cause

Alarm device open The wireless magnetic contact indicates “Door or window

open” because the magnet is not applied to the wireless

magnetic contact.

22:30

Quick start guide — Putting a device into commission

QSG_security_system_Alarm_Connect_en.fm Seite 8 Donnerstag, 31. Januar 2019 7:45 07

Perform a test Test the system and devices

Done! That's all. The security system Alarm Connect has been successfully set up, commis-

sioned and tested. What's next?

Change the test

project into a

“real” customer

project

Creating a customer project

Reopen GPA and expand the existing test project.

So that the customer project can be put into commission as “ready for use”, all devices in the

GPA must be located and configured.

After the project has been commissioned, the devices must first be mounted in accordance

with the enclosed instructions and then put into commissioned.

Next, a check can be performed on the wireless control unit by pressing the key (information

key) on the info page to see whether there are any faults or “open detectors” displayed.

Example: “Tamper alarm, alarm control unit”: In this case, the housing cover on the alarm

control unit Connect has not yet been pushed down to Position 0.

After eliminating all faults, the corresponding messages can be acknowledged on the info page

with the factory-assigned PIN (0001). Observe the notes regarding the PIN in the operating

instructions of the wireless operating unit.

If the devices from the test project are not installed directly at the customer, all batteries and

the battery pack must be removed from the devices before discharge, and stored in a safe place.

1. Hold the magnet to the wireless magnetic

contact.

The symbol turns off.

The “fault” is the only thing displayed.

2. Remove the magnet again.

The symbol reappears in the display.

Quick start guide — Testing the system and devices

QSG_security_system_Alarm_Connect_en.fm Seite 9 Donnerstag, 31. Januar 2019 7:45 07

The device list

Each device comes with two stickers and the hardware ID.

As shown in the example, you can adhere one of the two stickers to the enclosed device list.

Device list, Example

During configuration in the GPA, you can easily scan the hardware ID with an appropriate

scanner.

Seria

l No. Hardware ID Device name SB

1- Alarm control unit 1

2Wireless operating unit, Hall 1

3Magnetic contact, Front door 1

4Motion detector, Hall 1

01-00001

61-00001

07-00001

QSG_security_system_Alarm_Connect_en.fm Seite 10 Donnerstag, 31. Januar 2019 7:45 07

Autres manuels pour Alarm Connect

Table des matières

Autres manuels Gira Système de sécurité

Gira

Gira Alarm Connect Manuel utilisateur

Gira

Gira 2617 Series Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur