Gilson Centry 117 Manuel utilisateur

User’s Guide

Centry™117 Microcentrifuge

2CENTRY™ 117 MICROCENTRIFUGE | USER’S GUIDE

|CENTRY™ 117 MICROCENTRIFUGE

Trademarks

All product and company names are trademarks™ or registered® trademarks of their

respective holders. Use of the trademark(s) in this document does not imply any aliation

with or endorsements by the trademark holder(s).

CENTRY™ 117 MICROCENTRIFUGE | USER’S GUIDE

|CENTRY™ 117 MICROCENTRIFUGE

TABLE OF CONTENTS

Introduction | 4

Speciﬁcations | 4

General Safety Precautions | 5

Installation | 6

Operation | 7

Maintenance | 10

Troubleshooting | 13

Ordering Information | 15

Warranty | 15

4CENTRY™ 117 MICROCENTRIFUGE | USER’S GUIDE

INTRODUCTION |CENTRY™ 117 MICROCENTRIFUGE

Introduction

The CENTRY™ 117 Microcentrifuge is a compact, touchscreen,

benchtop microcentrifuge designed for separation of various

research samples. The motor is brushless and requires no

routine maintenance. The microcentrifuge is supplied with

a COMBI-Rotor™ for 24 microtubes (1.5–2.0 mL) and two

PCR-strips for micro volume samples. Adapters are available

for tubes smaller than 1.5 mL. The microcentrifuge reaches

speeds of up to 13,500rpm / 16,800 x g.

Speciﬁcations

CENTRY™ 117 MICROCENTRIFUGE

Dimensions (W x D x H) 22.86 x 30.48 x 19.7 cm / 9 x 12 x 7.75 in.

Maximum Speed 13,500 rpm

Maximum RCF 16,800 x g

Maximum Volume 1.5–2.0 mL (24 microtubes)

Admissible

SampleDensity 1.2 kg/dm3

Electrical 120V / 50-60Hz / 1.3A / 2.5 AT

230V / 50-60Hz / 0.7A / 1.25 AT

Operating Temperature 4°C to 35°C / 80%RH

Warranty 2 years

Angle COMBI-Rotor for 1.5 mL Tubes (Qty 24)

Tube Measurement 1.5 mL / 2.0 mL (10 x 40 mm)

Maximum Speed 13,500 rpm

Centrifuging radius 8.23 cm

Maximum Speed and

Maximum RCF (g-value) 16,800 x g

CENTRY™ 117 MICROCENTRIFUGE | USER’S GUIDE

INTRODUCTION |CENTRY™ 117 MICROCENTRIFUGE

General Safety Precautions

All users of the CENTRY 117 Microcentrifuge must read the

General Safety Precautions of this manual before attempting

to operate the unit!

If this equipment is used in a manner not specified by the

manufacturer, the protection provided by the equipment may

be impaired.

WARNING

Do not operate the CENTRY 117 Microcentrifuge if any of the

following conditions exist:

The microcentrifuge has not been installed properly.

The microcentrifuge is partially dismantled.

Service has been attempted by unauthorized or unqualiﬁed

personnel.

The rotor has not been installed securely on the motor shaft.

Rotors and accessories not belonging to the standard range

are being used without permission being obtained from the

manufacturer to use such rotors and/or accessories in the

microcentrifuge.

Exception: microcentrifuge tubes made of plastic, normally

available in the laboratory.

The microcentrifuge is located in an explosive atmosphere.

Materials to be centrifuged are combustible and/or explosive.

Materials to be centrifuged are chemically reactive.

The rotor load is not properly balanced.

Installation

6CENTRY™ 117 MICROCENTRIFUGE | USER’S GUIDE

INSTALLATION |CENTRY™ 117 MICROCENTRIFUGE

Installation

Unpacking

Before unpacking the CENTRY 117 Microcentrifuge, inspect

the outside of the carton for any shipping damage. The

CENTRY 117 Microcentrifuge is delivered in a carton with

protective foam cushioning.

1. Remove the CENTRY 117 Microcentrifuge from the carton.

2. Retain the carton and cushioning until it has been

established that the CENTRY 117 Microcentrifuge is

working.

NOTE

Shipping damage is the responsibility of the transportation

carrier. Any claims for damage must be ﬁled within 48 hours

with the carrier.

The accessories and instruction manual supplied with the

CENTRY 117 Microcentrifuge should be kept with the near its

place of installation.

Installation Site Requirements

The CENTRY 117 Microcentrifuge should be installed on a rigid,

even surface such as a stable laboratory bench, countertop,

etc. To guarantee sufficient ventilation, ensure that the

microcentrifuge has at least 15 cm (6 inches) of free space on

all sides, including the rear.

NOTICE

The CENTRY 117 Microcentrifuge should not be located in

areas subject to excessive heat such as in direct sunlight or

near radiators or the exhaust of a compressor, as a buildup of

heat may occur within the chamber.

CENTRY™ 117 MICROCENTRIFUGE | USER’S GUIDE

INSTALLATION |CENTRY™ 117 MICROCENTRIFUGE

Operation

Before operating the CENTRY 117 Microcentrifuge:

1. Check that the power source (electrical outlet on the wall)

corresponds to that on the manufacturer’s rating label.

2. Connect the power cord to the CENTRY 117 Microcentrifuge

and the power source.

WARNING

Never attempt to operate the CENTRY 117 Microcentrifuge

with rotors or adapters that show signs of corrosion or

mechanical damage.

Never centrifuge strongly corrosive materials that may

damage the rotors, accessories, or bowl of the unit.

Attach Rotor Lid

After the rotor has been properly secured and loaded, attach

the rotor lid to the rotor. Always use the rotor lid for safety and

to allow the rotor to reach proper speed. Make sure that the

rotor lid snaps securely into place.

NOTE

The CENTRY 117 Microcentrifuge locks when closed and the

start button is pressed.

Lid Lock

The lid will remain locked during a centrifuge run. Once the

run has been completed and the rotor has come to a stop,

a beep will indicate the end of a run, and the lid will unlock

automatically.

WARNING

Do not attempt to open the lid of the CENTRY 117

Microcentrifuge until the rotor has come to a complete stop.

8CENTRY™ 117 MICROCENTRIFUGE | USER’S GUIDE

OPERATION |CENTRY™ 117 MICROCENTRIFUGE

Manual Lid Release

In the event of a power failure or malfunction, it may be

necessary to open the lid manually.

1. Disconnect the power cord from the wall socket.

2. Remove the plastic plug, located on the left side of the unit.

3. Pull the wire (attached to the plug) to open the lid lock

manually.

WARNING

Do not attempt to override the lid lock mechanism.

Doing so is dangerous and could damage the CENTRY 117

Microcentrifuge.

Speed Selection

The speed (rpm or g-force) can

be selected from 1,000 to 13,500

rpm or from 100 to 16,800 x g by

touching the speed display and

adjusting with the up and down

arrow buttons.Display of rpm/rcf

can be toggled with the rPM/RCF

button on the display.

Load the Rotor

Tubes to be loaded should be filled equally

by eye. The difference in the weight

between the tubes should not exceed 0.1

gram. Tubes should always be loaded so

that there is equal spacing between all

tubes. One or two additional loaded tubes

may need to be added to achieve this.

Figure 1

MyTouch™ Control Panel Layout

Figure 2

Balanced Rotor Load

Figure 3

Incorrect Rotor Load

CENTRY™ 117 MICROCENTRIFUGE | USER’S GUIDE

OPERATION |CENTRY™ 117 MICROCENTRIFUGE

Start a Timed Run

Operating time can be selected from 0 min to 99 min

by pressing the Set Time button and adjusting with the

up and down arrow buttons. Setting the time at 0 will

put the MyTouch™ in continuous run. In this mode, the

CENTRY 117 Microcentrifuge will run until manually stopped.

To start a run, press the Start/Stop button.

When the preselected time expires, the

CENTRY 117 Microcentrifuge will stop automatically.

Start/Stop a Manual Run

The CENTRY 117 Microcentrifuge may be operated for a

short run by pressing and holding the Start/Stop button. The

microcentrifuge will continue to run as long as the button is

held down.

Stop a Run

To stop the CENTRY 117 Microcentrifuge prior to the expiration

of set time, press the Start/Stop button.

10 CENTRY™ 117 MICROCENTRIFUGE | USER’S GUIDE

MAINTENANCE |CENTRY™ 117 MICROCENTRIFUGE

Maintenance

Rotor Maintenance

The rotor should be cleaned regularly. Thorough cleaning must

be performed when spinning samples containing phenol or

phenol chloroform. Periodically inspect the rotor for dents,

dings, scratches, discoloration, and cracks. If any damage to

the rotor is found, discontinue use of the rotor immediately

and replace.

ROTOR REMOVAL

The rotor can be removed for cleaning.

1. Remove the rotor securing screw from the motor shaft

by turning the screw counterclockwise, using the rotor

wrench.

2. Lift the rotor directly upward in a straight vertical motion.

ROTOR INSTALLATION

1. Make sure that the motor shaft and rotor mounting hole are

clean.

2. Place the rotor on the motor shaft.

3. Reinstall the rotor securing screw on the motor shaft by

turning it clockwise.

4. Hold the rotor with one hand and tighten the rotor securing

screw, using the rotor wrench.

PCR HOLDER REMOVAL

Locate the tabs on each of the two

holders and pull them inward towards

the center of the rotor using a pair of

pliers.

Figure 4

PCR Holders

Table des matières

Autres manuels Gilson Équipement de laboratoire

Gilson

Gilson Vortex Mixer Manuel utilisateur

Gilson

Gilson CENTRY 103 Minicentrifuge Manuel utilisateur

Gilson

Gilson PIPETMAN P Manuel utilisateur

Gilson

Gilson pipetman Manuel utilisateur

Gilson

Gilson PIPETMAX Manuel utilisateur

Gilson

Gilson P10M Manuel utilisateur

Gilson

Gilson PIPETMAN P2L Manuel utilisateur

Gilson

Gilson Safe Aspiration Manuel utilisateur

Gilson

Gilson macroman Manuel utilisateur

Gilson

Gilson Pipetman Fixed Manuel utilisateur

Gilson

Gilson pipetman P10 Series Manuel utilisateur

Gilson

Gilson PIPETMAN M CONNECTED Manuel utilisateur

Gilson

Gilson GX-27X Series Manuel utilisateur

Gilson

Gilson ASPEC Manuel utilisateur

Gilson

Gilson Pipetman Classic Series Manuel utilisateur

Gilson

Gilson microman e Manuel utilisateur

Gilson

Gilson Pipetman M Manuel utilisateur

Gilson

Gilson pipetman Manuel utilisateur

Gilson

Gilson SGA-5RT Manuel utilisateur

Gilson

Gilson CENTRY 103 Minicentrifuge Manuel utilisateur

Gilson

Gilson PIPETMAN P Series Mode d'emploi

Gilson

Gilson PIPETMAN M P10M Manuel utilisateur

Gilson

Gilson PIPETMAN P Manuel

Gilson

Gilson MICROMAN E M10E Manuel utilisateur

Manuels Équipement de laboratoire populaires d'autres marques

Qiagen

Qiagen DML 3000 Manuel utilisateur

Queensgate

Queensgate NANOSCAN OP400 Manuel de programmation

Conviron

Conviron GEN1000-GE Manuel utilisateur

Parr Instrument

Parr Instrument 4560 Mode d’emploi

IKA

IKA IC control Manuel utilisateur

Integra

Integra DOSE IT Manuel utilisateur

Agilent Technologies

Agilent Technologies 5800 ICP-OES Manuel utilisateur

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manuel utilisateur

NI PXI-5422 Manuel

Collomix

Collomix Aqix Manuel utilisateur

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manuel utilisateur

Ocean Insight

Ocean Insight FLAME-NIR+ Manuel utilisateur

Parker

Parker ALIGN-MG-NA Manuel utilisateur

BD 644787 Manuel utilisateur

DENTAURUM

DENTAURUM Compact Megaplus Manuel utilisateur

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manuel utilisateur

VWR

VWR SAS Super IAQ Manuel utilisateur

illumina

illumina MiSeqDx Manuel utilisateur