Gigabyte GS-SR104 Guide de l'utilisateur
System installation Guide
1-i
GS-SR104
Rack Mount Server
System Installation
Guide
System installation Guide
1-ii
INDEX
1. INTRODUCTION 1-1
1.1. PREFACE 1-1
1.2. FEATURES 1-1
2. HARDWARE INVENTORY 2-1
3. SYSTEM INSTALLATION PROCEDURES 3-1
3.1. CHASSIS COVER REMOVAL 3-1
3.2. CPU INSTALLATION 3-2
3.3. HEAT SINK INSTALLATION 3-2
3.4. MEMORY INSTALLATION 3-3
3.5. HARD DISK DRIVE INSTALLATION 3-3
3.6. PCI EXPANSION CARD INSTALLATION 3-5
3.7. REINSTALL TOP COVER 3-7
3.8. DOCK HANDLES INSTALLATION 3-7
3.9. FRONT PANEL 3-8
3.10. REAR PANEL 3-9
3.10.1. LCD MODULE INSTALLATION ( OPTIONAL ) 3-9
3.10.2. LCD MODULE SETTING INSTRUCTION 3-10
3.10.3. LCD DISPLAY INFORMATION 3-11
3.10.4. USING THE LCD MODULE 3-12
3.11. CONNECTOR ICONS 3-13
System installation Guide
1-1
1. INTRODUCTION
1.1. Preface
Using this manual will help you get the most from
your Rack Mount Server. Keeping the manual with
your Rack Mount Server to refer when you want
information and help.
In order to get the optimal usage out of your Rack
Mount Server and you should Remember the
following:
Read through all the instruction for your Rack
Mount Server .
Keep the area free of static electricity and
magnetic fields. These can damage the Serve .
When cleaning the server or its components, apply
the proper cleaning solutionor sprays only on the
cloth ,not to the server or its components .
1.2. Features
Our Rack Mount Server use 1U Chassis and support
the following features:
Processor Support
Single Socket 370 for Intel Coppermine ‘ Celeron
( 0.13 u ) and Tualatin processor
Up to 1 GHz and above
Optimal CPU Keep Out Zone for Type C
Heat-sink
100/133MHz FSB
System installation Guide
1-2
AUTO detect CPU voltage
BIOS
Award BIOS 2M bit flash ROM
Auto configure IDE HDD type
Multiple boot options
User setting for hardware monitoring
DMI 2.0 compliant
Chipset
VIA Apollo Pro Family AGP set
( VT82C694T ,VT82C686B ) Chipset
ATI Rage XL VGA Chip with 8MB Video
Memory
Intel 82559 Dual LAN chip
Memory Support
2 x 168-pin 25 degree DIMM sockets for SDRAM
modules
Supports PC-100/PC-133 either un-buffered or
registered memory and VCM SDRAM
Supports up to 2GB SDRAM
Supports only 3.3V SDRAM DIMM
Storage Controller
Max 2 IDE ATA channels ( 2 x ATA-100 )
44MB Floppy Disk Drive
High Speed IDE CD-ROM Drive ( Slim type )
Networking
On board dual LAN , Ethernet 10/100 WOL ( Wake
On LAN )
Adaptive fail over feature
Load balance feature
System installation Guide
1-3
I/O Expansion Slot
PCI riser , 1 slot ,support 33MHz & PCI 2.2
compliant
Build-in I/O ports
1 x PS/2 Keyboard port
1 x PS/2 Mouse port
2 x COM port ( 1 x back side and 1 x front side )
1 x VGA port
1 x LPT port
2 x RJ-45 ports
2 x USB ports
Power
Total output power 150 W
Input : Rating switch full range 90V~250V
47~63 Hz
Operating Temperature
5 to 35 degree C
Thermal Solution
Special-designed Heat-sink and hi-efficiency
chassis fans for dual 1 GHz plus processor
thermal solution
Chassis Dimensions
Height 44 mm ( 1.73 In. )
Width 482.6 mm ( 19.0 In. )
Depth 495.3 mm ( 19.5 In. )
System installation Guide
2-1
2.Hardware Inventory
When you unpack your GS-SR104 Rack Mount
Server ,Check that all the items that you ordered are
present in good condition. Review the inventory
checklist below to be sure that the components and
optional components that you ordered are included. If
anything is miss or damage ,contact your retailer as
soon as possible.
Chassis
Power Supply (Installed)
Motherboard GA-6VTMR (Installed)
Power Cord x1
Manual (M/B User’s Manual & System
Installation)
Flat Screw # 6-32 * 5L x 12 (For HDD)
Heat sink x 1
Case Handle x 2
Flat Screw M4*10L x 4 (For Handle)
Support CD x1
Support Floppy Disk x 2
System installation Guide
3-1
3.System Installation
Procedures
Warning: Please remove the protective thin films
(Top and Bottom) from the system when installing.
3.1. Chassis Cover Removal
a. Unscrew the two thumbscrews from top cover of
the system (Fig-1).
b. Standing at the front of the system. Gently apply
force to the indentures with your thumbs and
push toward the rear of the chassis for about 3/4
of an inch. Top cover may be lifted straight up
(Fig-2).
Fig-1 Fig-2
c. With the top cover removed, you will see a
transparent plastic air duct over the CPU and
Memory. Remove the air duct to install the
CPU and Memory (Fig-3).
System installation Guide
3-2
Fig-3
3.2. CPU Installation
Lift the ZIF (Zero Insertion Force) socket lever
up 90 degree. Insert CPU into the socket. Make
sure CPU is seated properly, then push the level
back to the original locked position. (Fig-4 and
Fig-5 )
Fig-4 Fig-5
3.3. Heat Sink Installation
Place the heat sink on top of the CPU with the clip
handle on the same side as DIMM slot . Clip one side
(without handle) onto the CPU socket’s hook and
gently push the other side of the clip (with handle) on to
the opposite side of the CPU socket’s hook. (Fig-6 )
Autres manuels pour GS-SR104
1
Table des matières
Autres manuels Gigabyte Serveur
Gigabyte
Gigabyte G292-Z24 Manuel utilisateur
Gigabyte
Gigabyte R183-S96-AAD1 Manuel utilisateur
Gigabyte
Gigabyte R282-Z93 Manuel utilisateur
Gigabyte
Gigabyte R282-G30 Manuel utilisateur
Gigabyte
Gigabyte H263-S64-AAN1 Manuel utilisateur
Gigabyte
Gigabyte R183-Z90-AAV1 Manuel utilisateur
Gigabyte
Gigabyte G241-G40 Manuel utilisateur
Gigabyte
Gigabyte G152-Z12 Manuel utilisateur
Gigabyte
Gigabyte H262-P61 Manuel utilisateur
Gigabyte
Gigabyte GS-SR 125E Manuel utilisateur
Gigabyte
Gigabyte S453-S70-AAV1 Manuel utilisateur
Gigabyte
Gigabyte E252-P30 Manuel utilisateur
Gigabyte
Gigabyte GS-R12T4S Manuel utilisateur
Gigabyte
Gigabyte GS-R115L-RH Guide de l'utilisateur
Gigabyte
Gigabyte R183-Z91 Manuel utilisateur
Gigabyte
Gigabyte G242-Z10 Manuel utilisateur
Gigabyte
Gigabyte TO15-Z40-IA01 Manuel utilisateur
Gigabyte
Gigabyte GS-SR103 Guide de l'utilisateur
Gigabyte
Gigabyte R183-Z92-AAD1 Manuel utilisateur
Gigabyte
Gigabyte H242-Z10 Manuel utilisateur
