PARTYMODE®(HOLD OPEN) FUNCTION
Enabling PartyMode®through a remote transmitter sends a command/message to the gate controller to turn PartyMode®function On or O. The gate opener system
will remain in PartyMode®until the gate controller receives a signal to be disabled or the power button on the Control Box is cycled to the o position. Once PartyMode®
has been disabled, all functions such as AUTOCLOSE will return to their previous operation.
TO ENABLE PARTYMODE®
STEP LED/ALARM
BEFORE PRESSING
BUTTON(S) SEQUENCE
TO PRESS
LED/ALARM
AFTER PRESSING DESCRIPTION
1Press & hold on Remote
until the LED goes
LED on Remote goes Tells the Remote transmitter that you are about to enter into PartyMode®
2Remote LED is Press & release or
on Remote LED goes
This places the main system controller into PartyMode®until you disable it or if you cycle the ON/OFF
switch on the gate system control box. Gate will open and remain open at the full open position if not
already at the limit. All remotes and other controls such as keypads are ignored (but are acknowledged
with two beeps from gate system alarm) once the gate is at the open limit.
TO DISABLE PARTYMODE®
1Press & hold on Remote
until the LED goes
LED on Remote goes Tells the Remote transmitter that you are about to exit PartyMode®
2Remote LED is Press & release or
on Remote LED goes This disables PartyMode®on the main system controller and enables AUTOCLOSE if it was previously
enabled. Gate will close automatically if AUTOCLOSE is enabled.
GATE SYSTEM CONTROLLER DIAGNOSTIC MODE
Diagnostic Mode function sends a command/message to the gate controller to activate diagnostics indicators (LEDs and/or alarm codes) on the gate controller. Refer to
the gate opener manual for specific details about the indicators. To conserve the battery power, the main controller indicators (LEDs and alarm) are turned o when gate
is idled for more than 60 seconds (except for UL-325 requirement for entrapment protection). Enabling Diagnostic Mode will turn these indicators on for 5 minutes
without the need to operate the gate.
IMPORTANT
Pressing the Test button on the remote transmitter indicates the status of the gate system controller battery. It does not indicate the status of the CR2032 battery
inside of the remote itself.
TO TEST YOUR GATE SYSTEM CONTROLLER
STEP LED/ALARM
BEFORE PRESSING
BUTTON(S) SEQUENCE
TO PRESS
LED/ALARM
AFTER PRESSING DESCRIPTION
1Press & hold on Remote
until the LED goes
LED on Remote goes
Tells the Remote transmitter that you are about to enter into Test Mode
2Remote LED is Press & release or
on Remote LED goes The gate system controller will use the gate alarm to indicate the gate status.
1 Beep=Battery is good.
2 Beeps=Battery is low.
GENERATING A NEW TRANSMITTING KEY CODE
CAUTION
Please READ and PROCEED with CAUTION
Each GHOST CONTROLS®remote transmitter has a unique key code sequence. Once a new key sequence is generated, the previous key code is lost. The new key code
will need to be programmed or “learned” into the gate opener to control the gate.
STEP LED/ALARM
BEFORE PRESSING
BUTTON(S) SEQUENCE
TO PRESS
LED/ALARM
AFTER PRESSING DESCRIPTION
1
Press & hold AND
simultaneously for 10seconds
on Remote until the LED goes
LED on Remote goes
Tells the remote transmitter (Remote B) that you are going to generate a new code. Step 2 & 3 must be
completed within 5 seconds while the LED is lit.
2Release AND
3Remote LED is Press & release or
on Remote LED goes The remote button pressed in this step is now generating a new code.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
■This device may not cause harmful interference
■This device must accept any interference received, including interference that may cause undesired operation.
WARNING G
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable pro-
tection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
■Reorient or relocate the receiving antenna
■Increase the separation between the equipment and receiver.
■Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
■Consult the dealer or an experienced technician for help.
www.GhostControls.com
Made in China, Rev. 2017-07
WARNING: This product can expose you to chemicals including lead, which is known
to the State of California to cause cancer. For more information, go to
www.P65Warnings.ca.gov
