GFS E-Bar 700 70 Series Manuel utilisateur

GfSSafetey at doors

GfS – Gesellschaft für Sicherheitstechnik GmbH

Tempowerkring 15 ∙ 21079 Hamburg ∙ Fon 040-79 01 95-0 ∙ Fax 040-79 01 95 11 ∙ [email protected]

Assembly instruction

GfS e-Bar®

GfSSafety at doors

7007xx_MA_GfS e-Bar_0518_GB

GfSSafety at doors

Content

1. Introduction Seite

1.1.0 Safety instructions .....................................................................4

1.2.0 General functions ......................................................................5

1.2.1 Local alarm types ......................................................................6

1.2.2 Operation.............................................................................7

1.3.0 Mechanical versions of GfS e-Bar® ........................................................8

1.3.1 Mechatronic versions of GfS e-Bar® .......................................................9

2. Assembly

2.1.0 Mounting instructions of GfS e-Bar® ......................................................10

2.1.1 Cut to size with tool kit.................................................................11

2.2.0 Deﬁning the correct length..............................................................12

2.3.0 Adjusting main alarm ..................................................................13

2.4.0 Changing the cylinder ..................................................................14

2.5.0 Mounting on wooden doors .............................................................15

2.5.1 Mounting on metal doors ...............................................................16

2.5.2 Mounting in combination with security escutcheon (4mm) ....................................17

2.6.0 Battery operation/mains supply – wiring of GfS e-Bar®.......................................18

2.7.0 Assembly of GfS e-Bar® ................................................................19

2.8.0 Placing the stickers....................................................................20

3. Electrical connection

3.1.0 Terminal board GfS e-Bar® 700 71x .......................................................21

3.1.1 Terminal board GfS e-Bar® 700 73x .......................................................22

3.1.2 Terminal board GfS e-Bar® 700 74x .......................................................23

3.2.0 Wiring diagram GfS e-Bar® 700 71x ......................................................24

3.2.1 Wiring diagram GfS e-Bar® 700 73x ......................................................25

3.2.2 Wiring diagram GfS e-Bar® 700 74x ......................................................26

4. GfS e-Bar® settings...........................................................................27

4.1.0 Activate automatic alarm switch-o ......................................................27

4.1.1 Settings of DIP switch .................................................................27

4.1.2 RS485-Interface with MODBUS protocol ..................................................27

4.1.3 Switching color green/red ..............................................................27

4.1.4 Changing brightness ...................................................................27

5. Technical data...............................................................................28

6. Documentation

6.1.0 Service protocol (operator) ..............................................................29

6.2.0 Service protocol (installer) ..............................................................30

This document has been produced with the utmost care. GfS does not guarantee the accuracy or completeness of the content of this documentation with respect to texts, pictures , references or information

contained therein. The company GfS assumes no liability for damages arising directly, indirectly or accidentally from the use of this documentation. The content of this documentation may be adjusted without

notice. It shall not lead to any obligations for GfS in the future.

This documentation may not be reproduced without written permission of GfS – Gesellschaft für Sicherheitstechnik GmbH in any way, or otherwise used.

*GfS e-Bar® mechanical has no display

7007xx_MA_GfS e-Bar_0518_GB

GfSSafety at doors

1.0 Introduction

1.1.0 Safety instructions

The GfS e-Bar may only be installed acc. to the speciﬁcations of the assembly instruction.

• the door must have a smooth running without distortion

• the door leaf should be ﬂat and sti

• existing door seals must not aect the door function

• the GfS e-Bar® may only be mounted horizontally on doors that open outwards

• the GfS e-Bar® may only be used with approved panic locks and ﬁttings (EN 1125)

• the GfS e-Bar® should be cut to length as required according to the installation instructions

• if used on glass doors, there should be safety glazing

• the GfS e-Bar® is not suitable for use on swing doors

When changing cylinders only use half cylinder with lockable driver! (Type information see technical data)

The assembly must be carried out by qualiﬁed sta.

After installation the assembly instruction has to be handed over to the operator.

Protect against water and vandalism!

7007xx_MA_GfS e-Bar_0518_GB

GfSSafety at doors

Function GfS e-Bar®

mechanic

700 70*

GfS e-Bar®

mechanic with

ﬂoating contacts

700 71*

GfS e-Bar®

mechatronic

700 73*

GfS e-Bar®

mechatronic

with emergency

exit switch

700 74*

Communicating display accoustic/visual X X

For door leaf left/right XXXX

Battery-powered (incl. battery control) X

External power supply X X

Main alarm with ﬂoating contact XXX

Pre-alarm with ﬂoating contact XXX

Single release (local or remote) XXX

Permanent release (local or remote) X X

Visual and acoustic “door-too-long-open” alarm X X

Intrusion alarm X X

Integrated emergency exit switch X

Changing display to green/red X X

RS 485 MODBUS Interface X X

DIP Switch X X

1.2.0 General functions

7007xx_MA_GfS e-Bar_0518_GB

GfSSafety at doors

1.2.1 Local alarm types

GfS e-Bar® activated

When activated the green LEDs of the wired GfS e-Bar is permanently

switched on. The green display means that the door is alarm-secured but

might be opened at any time. In case of battery supply, the GfS e-Bar®

works in an energy saving mode without background light. The display

brightens only for about 15 sec.

Pre-alarm

While slightly pressing the GfS e-Bar® a red ﬂashing light and an accous-

tic alarm (95 dB A/1m) is emitted, which expires as soon as the GfS e-

Bar® is released. The moment the pre-alarm turns into a permanent alarm

can be adjusted with a little screw (see p. 13). The pre-alarm can be

transmitted to a central display.

Main alarm

When pressing the GfS e-Bar® completely the door is released. At the

same time the display ﬂashes an intermittent green light and a permanent

alarm sound with 95 dBA. The accoustic and visual alarm can just be

switched o by turning the integrated key switch. The main alarm might

be transmitted to a central display.

Battery Control

When battery operated the GfS e-Bar® a gentle warning signal is emitted

every 60 sec. as soon as the voltage drops below 7 V. The display is o.

The alarm is active till a new battery is connected or the old battery is

empty.

Door-too-long-open-Alarm

Pre-condition for this feature is a Reed contact which is installed

on the door and connected to the GfS e-Bar®. When the single re-

lease has been activated by the integrated key switch and the

door stays open for more than 15 sec. a gentle ”Door-too-long-

open-Alarm” is emitted in an interval of 3 sec. The alarm sound in-

dicates that an authorized person has left the door open. As soon

as the door is closed the sound is o

Display: green

Display: red

Display: ﬂashes green

7007xx_MA_GfS e-Bar_0518_GB

GfSSafety at doors

1.2.2 Operation

Reset

By brieﬂy turning the key clockwise the main alarm is deactivated. The

key needs to be turned by 90° and back. The impulse should be no longer

than 1 sec. 15 sec. after this operation the GfS e-Bar® is alarm secured

again which is indicated by a green display (mains supply). When battery

operated the green display fades away after another 15 sec.. If a reed

contact is installed the GfS e-Bar® will be alarm secured the moment the

door closes.

Single release

By using the integrated key switch or by employing an external access

control system (p. 22, p.23), an authorized person may pass the emergen-

cy exit once without causing an alarm.

By brieﬂy turning the key clockwise the single release mode is triggered.

The key needs to be turned by 90° and back. The impulse should be no

longer than 1 sec. If a reed contact is installed the GfS e-Bar® will be

alarm secured the moment the door closes.

If the door is kept open for more than 15 sec. a gentle “Door-too-long-

open-Alarm” resounds till the door is closed again.

Permanent release

By using the integrated key switch an authorized person may deactivate

the GfS e-Bar® in order to pass the emergency exit for a longer period of

time. The permanent release is triggered by turning the key clockwise for

at leat 5 sec. The key needs to be turned by 90° and back.

The status is communicated by a raising and lowering brightness of the

green display.

The key should be removed. The permanent release is activated till the

key is turned again by min. 90° for max. 1 sec. and removed afterwards.

Alternatively the permanent release can be set by access control systems,

timer etc. (p. 22, p. 23).

(

)

∙

right

(

)

∙

left

(

)

∙

right

(

)

∙

left

7007xx_MA_GfS e-Bar_0518_GB

GfSSafety at doors

1.3.0 Mechanical versions of GfS e-Bar®

1. GfS e-Bar® mechanic

This model is a push bar incl. a picto describing the operation of the GfS e-Bar®. Neither contacts nor electric functions are

included. The GfS e-Bar® mechanic will be supplied in three dierent lengths, which might be shortened individually, in order

to adjust the length to the width of the door.

Length in mm To be shortened by mm Art. No.

970 180 700 700

1130 160 700 703

1290 160 700 705

2. GfS e-Bar® mechanic with ﬂoating contacts

This model is a push bar with ﬂoating contacts to generate information on the usage of the push bar.

The items will be delivered with a picto describing the operation of the GfS e-Bar®. The GfS e-Bar® mechanic will be supplied

in three dierent lengths, which might be shortened individually, in order to adjust the length to the width of the door.

Length in mm To be shortened by mm Art. No.

970 180 700 710

1130 160 700 713

1290 160 700 715

970/1130/1290

6.5

71.3 84.7

To be shortened by 180/160/160 mm

Distance between fastening points

970/1130/1290

43/50

71.3 84.7

Display for GfS e-Bar® mechatronic

To be shortened by 180/160/160 mm

Distance between fastening points

7007xx_MA_GfS e-Bar_0518_GB

GfSSafety at doors

1.3.1 Mechatronic versions of GfS e-Bar®

1. GfS e-Bar® with integrated alarm (battery operated and/or mains supplied)

This model works either with a 9 V battery which is controlled by the PCB or with mains supply of 10−30 V/DC.

The battery control function checks every 10 hours the voltage. If the voltage drops below 7V, all 60 seconds an accoustic alarm is emitted.

The battery has to be changed. When battery operated the GfS e-Bar® works in an energy saving mode which basically means that the

green LEDs of the display are permanently switched o.

The intelligent PCB recognizes when an external power supply is connected to the GfS e-Bar®. The communicating display shines permanently

green. It indicates that the emergency exit is alarm secured. Delivery includes 1 9V battery, 2 keys, 1 picto for display and key switch as well as

one sticker explaining the operation on the door.

Length in mm To be shortened by mm Art. No.

970 180 700 730

1130 160 700 733

1290 160 700 735

Power supply surface mounted 901 366

Power supply ﬂush mounted 700 006

2. GfS e-Bar® with integrated alarm and emergency exit switch for opening electrically locked doors

The GfS e-Bar with integrated emergency exit switch is operated at 10−30 V/DC which is either supplied by an external power supply or the

FWS-02 (Emergency exit control unit). The integrated emergency exit switch with 2 opening contacts might be connected to the emergency exit

control unit with a max. load of 3A. Adiitionally it is recommended to install a reed contact which oers additional features such as immediate

activation after the door has been closed and door-too-long-open-alarm.

Delivery includes 1 integrated emergency exit switch, 2 keys, 1 picto for the display and the key switch as well as one sticker explaining the

operation on the door.

Length in mm To be shortened by mm Art. No.

970 180 700 740

1130 160 700 743

1290 160 700 745

Power supply surface mounted 901 366

Power supply ﬂush mounted 700 006

7007xx_MA_GfS e-Bar_0518_GB

GfSSafety at doors

2.0 Assembly

2.1.0 Mounting instructions of GfS e-Bar®

Countersunk screw M3 x 8 Clamping bolt

Lever arm

Cylinder head screw M5 x 20

push bar

base proﬁl

While pressing the push bar proﬁle 4remove the cylinder head screw M5 x 20 1.

Tear the cover hood 1a out of the bayonet joint towards the lock side.

GfS e-Bar® mechatronic

Remove the screw M3 x 8 9, unlock the cover hood by turning the key clockwise 2a .

GfS e-Bar® mechanic

While the push bar is pressed 4remove the cylinder head screw M5 x 8. Tear the cover hood 2towards the hinge side.

Remove the protective shield 10 .

Lift the push bar proﬁle 4up to its maximum. Hold the lever arm 7with one hand and remove the

push bar proﬁle 4from the clamping bolt in opposite direction 7a .

Autres manuels pour e-Bar 700 70 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels GFS Système de sécurité

GFS

GFS Day Alarm Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur

GFS e-Bar 700 70 Series Manuel utilisateur

Manuels Système de sécurité populaires d'autres marques