GeoVision GV-Video Server Guide d'installation et d'utilisation

GeoVision Inc. 1 Revision Date: 2009/8/25

How to Load Default Settings for GV-Video Server,

GV-Compact DVR or GV-IP Camera

Article ID: GV-15-09-08-24

Release Date: 08/24/2009

Applied to

GV-Video Server (GV-VS02, GV-VS02A, GV-VS04A, GV-VS12)

GV-Compact DVR V1 and V2

GV-IP Camera V1

Summary

Among different models of GV-Video Servers, GV-Compact DVRs and GV-IP Cameras, the

time of loading default settings for each model can vary and the way the LEDs flash can also

be different.

Loading Default Settings for GV-Video Server

(GV-VS02, GV-VS02A and GV-VS04A)

The figure below is the front panel of GV-VS02. Since the front panels of GV-VS02,

GV-VS02A and GV-VS04A are very similar, refer to the figure and the instructions below to

load default values for the three models of GV-Video Servers.

GeoVision Inc. 2 Revision Date: 2009/8/25

1. Press and then release the Reset button immediately.

2. Press and hold the Load Default button until all 3 LEDs (Power, Ready and Disk

Full/Fault) are on. This may take up to 30 seconds.

3. Release the Load Default button. The process of loading default values is complete, and

the GV-Video Server starts rebooting itself with all 3 LEDs turning off.

4. Wait until the Power and Ready LEDs turn on again. After this all the settings are returned

to default values.

Note: Before the Ready LED is on again, do not unplug the power cable; otherwise the

loading of default values will fail.

Loading Default Settings for GV-Video Server (GV-VS12)

Refer to the figure and instructions below to load default settings for GV-VS12.

1. Unplug and plug the power cable to start.

2. Press and hold the Default button until the Ready LED blinks. This may take up to 30

seconds, and the Ready LED will blink twice.

3. Release the Default button. The process of loading default values is complete, and the

GV-Video Server starts rebooting itself with the 2 LEDs turning off.

4. Wait until the Power and Ready LEDs turn on again. After this all the settings are returned

to default values.

Note: Before the Ready LED is on again, do not unplug the power cable; otherwise the

loading of default values will fail.

GeoVision Inc. 3 Revision Date: 2009/8/25

Loading Default Settings for GV-Compact DVR V1 and V2

Refer to the figures and instructions below to load default settings for GV-Compact DVR V1

and V2. Please note the locations of Default buttons and Reset buttons on GV-Compact DVR

V1 and V2 are reversed.

Default Button

Reset Button

3 LEDs

3 LEDs Reset Button

Default Button

GV-Compact DVR V1 GV-Compact DVR V2

1. Press and then release the Reset button immediately.

2. Press and hold the Default button until the 3 LEDs (Power, Ready and Disk Full/Fault) are

on. This may take up to 30 seconds.

3. Release the Default button. The process of loading default values is complete, and the

GV-Compact DVR starts rebooting itself with the 3 LEDs turning off.

4. Wait until the Power and Ready LEDs turn on again. After this all the settings are returned

to default values.

Note: Before the Ready LED is on again, do not unplug the power cable; otherwise the

loading of default values will fail.

GeoVision Inc. 4 Revision Date: 2009/8/25

Loading Default Settings for GV-IP Camera V1

Refer to the figure and instructions below to load default settings for GV-IP Camera V1.

Default Button

1. Press and hold the Default button for about 10 seconds.

2. Release the Default button. After this all the settings are returned to default values.

Autres manuels pour GV-Video Server

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels GeoVision Serveur

GeoVision

GeoVision GV-DSP LPR V1 Manuel utilisateur

GeoVision

GeoVision GV-DSP LPR Manuel utilisateur

GeoVision

GeoVision GV-VS04H Manuel utilisateur

GeoVision

GeoVision GV-VS01 Manuel utilisateur

GeoVision

GeoVision GV-GIS Manuel utilisateur

GeoVision

GeoVision GV-VS02 Manuel utilisateur

GeoVision

GeoVision GV-VS04H Manuel utilisateur

GeoVision

GeoVision GV-Video Server Manuel utilisateur

GeoVision

GeoVision GV-VS04H Manuel utilisateur

GeoVision

GeoVision GV-Video Server Manuel utilisateur

GeoVision

GeoVision VSV13-A-EN Manuel utilisateur

GeoVision

GeoVision GV-AI System Manuel utilisateur

GeoVision

GeoVision GV-Recording Server Manuel utilisateur

GeoVision

GeoVision GV-Tower System V2 Manuel utilisateur

GeoVision

GeoVision GV-Mobile Manuel utilisateur

GeoVision

GeoVision GV-VS04H Manuel utilisateur

GeoVision

GeoVision GV-VS04H Manuel utilisateur

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur